2022 NISSAN GT-R suspension

Check the coolant level in the pressurized
coolant reservoir. Adjust the level so that
the fluid is between the MAX and MIN
markings. For the coolant, use genuine
NISSAN Long Life coolant or equivalent.
(On delivery of new vehicle, the reservoir
is filled to the MIN level. Be sure to
replenish approximately 3/8 US quart
(0.3 to 0.4 liter) of coolant.)
NOTICE
Do not overfill the coolant. This may
increase the pressure in the cooling
system and cause coolant leaks.
To maximize vehicle performance, the
coolant mixture ratio should be a combi-
nation of 30% coolant antifreeze and 70%
demineralized or distilled water for max-
imum cooling system performance re-
gardless of ambient temperatures.
If ambient temperatures are anticipated
below 5°F (−15°C), make sure a proper
mixture ratio of 50% antifreeze and 50%
demineralized or distilled water mix is
used.Engine and powertrainThe information and specifications in
this section apply only when engaging in performance driving.
.
Check the engine, transmission, differ-
ential and under the vehicle for oil and
coolant leaks.
. Inspect the areas surrounding of the
catalytic converter for heat deteriora-
tion.
. Always perform the transmission
setting. After that, adjust the clutch
clearance so that the clearance is less
than the clearance used for daily
driving. Your GT-R certified NISSAN
dealer has the necessary information
and equipment to set the clutch
clearance to the correct specification.
The clearance used for daily driving
increases clutch heat generated dur-
ing Performance Driving. This leads to
an increase in temperature of the
transmission oil. In addition, a more
direct shifting feel can be obtained by
reducing the clutch clearance for
Performance Driving. The clutch clear-
ance should be reset to the daily
driving specification after Perfor-
mance Driving. It is recommended
you see a GT-R certified NISSAN dealer
for information.
NOTICE
Failure to have the clutch properly
adjusted before performance driving
may cause the transmission oil tem-
perature to increase which may
cause transmission damage.
. Inspect and confirm the clearance
between the exhaust finisher and rear
bumper is more than 0.24 in (6 mm)
(up/down) and more than 0.20 in (5
mm) (left/right).
. Inspect the dust boot of the drive
shaft universal joint for cracks or
damage.Suspension and wheel alignmentThe information and specifications in
this section apply only when engaging
in performance driving.
.Check the steering and suspension
system and other links for loose and/
or damaged parts.
. Measure and adjust the wheel align-
ment. (
“Wheel alignment” page
GTR-10) It is recommended you con-
tact a GT-R certified NISSAN dealer to
adjust the wheel alignment to the
recommended setting for high perfor-

Check the coolant level in the pressurized
coolant reservoir. Adjust the level so that
the fluid is between the MAX and MIN
markings. For the coolant, use genuine
NISSAN Long Life coolant or equivalent.
(On delivery of new vehicle, the reservoir
is filled to the MIN level. Be sure to
replenish approximately 3/8 US quart
(0.3 to 0.4 liter) of coolant.)
NOTICE
Do not overfill the coolant. This may
increase the pressure in the cooling
system and cause coolant leaks.
To maximize vehicle performance, the
coolant mixture ratio should be a combi-
nation of 30% coolant antifreeze and 70%
demineralized or distilled water for max-
imum cooling system performance re-
gardless of ambient temperatures.
If ambient temperatures are anticipated
below 5°F (−15°C), make sure a proper
mixture ratio of 50% antifreeze and 50%
demineralized or distilled water mix is
used.Engine and powertrainThe information and specifications in
this section apply only when engaging in performance driving.
.
Check the engine, transmission, differ-
ential and under the vehicle for oil and
coolant leaks.
. Inspect the areas surrounding of the
catalytic converter for heat deteriora-
tion.
. Always perform the transmission
setting. After that, adjust the clutch
clearance so that the clearance is less
than the clearance used for daily
driving. Your GT-R certified NISSAN
dealer has the necessary information
and equipment to set the clutch
clearance to the correct specification.
The clearance used for daily driving
increases clutch heat generated dur-
ing Performance Driving. This leads to
an increase in temperature of the
transmission oil. In addition, a more
direct shifting feel can be obtained by
reducing the clutch clearance for
Performance Driving. The clutch clear-
ance should be reset to the daily
driving specification after Perfor-
mance Driving. It is recommended
you see a GT-R certified NISSAN dealer
for information.
NOTICE
Failure to have the clutch properly
adjusted before performance driving
may cause the transmission oil tem-
perature to increase which may
cause transmission damage.
. Inspect and confirm the clearance
between the exhaust finisher and rear
bumper is more than 0.24 in (6 mm)
(up/down) and more than 0.20 in (5
mm) (left/right).
. Inspect the dust boot of the drive
shaft universal joint for cracks or
damage.Suspension and wheel alignmentThe information and specifications in
this section apply only when engaging
in performance driving.
.Check the steering and suspension
system and other links for loose and/
or damaged parts.
. Measure and adjust the wheel align-
ment. (
“Wheel alignment” page
GTR-10) It is recommended you con-
tact a GT-R certified NISSAN dealer to
adjust the wheel alignment to the
recommended setting for high perfor-

The Vehicle Dynamic Control (VDC) sys-
tem uses various sensors to monitor
driver inputs and vehicle motion. Under
certain driving conditions, the VDC sys-
tem helps to perform the following func-
tions.
.Controls brake pressure to reduce
wheel slip on one slipping drive wheel
so power is transferred to a non
slipping drive wheel on the same axle.
. Controls brake pressure and engine
output to reduce drive wheel slip
based on vehicle speed (traction con-
trol function).
. Controls brake pressure at individual
wheels and engine output to help the
driver maintain control of the vehicle
in the following conditions:
— understeer (vehicle tends to not
follow the steered path despite
increased steering input)
— oversteer (vehicle tends to spin due to certain road or driving condi-
tions).
The VDC system can help the driver to
maintain control of the vehicle, but it
cannot prevent loss of vehicle control in
all driving situations.
When the VDC system operates, the VDC
warning light
in the meter flashes so note the following:
.
The road may be slippery or the
system may determine some action
is required to help keep the vehicle on
the steered path.
. You may feel a pulsation in the brake
pedal and hear a noise or vibration
from under the hood. This is normal
and indicates that the VDC system is
working properly.
. Adjust your speed and driving to the
road conditions.
. The VDC mode can be changed using
the VDC setup switch. (
“VDC,
transmission and suspension setup
switches” page 5-25)
(
“Vehicle Dynamic Control (VDC)
warning light” page 2-34,
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
If a malfunction occurs in the system, the
VDC warning light
illuminates in the
meter. The VDC system automatically
turns off.
The VDC setup switch is used to turn off
the VDC system. The VDC off indicator
illuminates to indicate the VDC sys-
tem is off.
When the VDC setup switch is used to
turn off the system, the VDC system still
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM

to detect
engine booming noise. The system then
automatically generates a noise cancel-
ling sound through the speakers
and
woofer
to reduce engine booming
noise.
The front and rear microphones
are
located inside of the roof.
The front speakers are located on the
doors and the woofer is located in
between the rear seats.
ACTIVE SOUND ENHANCEMENTThe active sound enhancement gener-
ates sounds according to engine speed
and driving modes selected by the Vehicle
Dynamic Control (VDC) system, transmis-
sion and suspension setup switches
through the speakers
and woofer
to enhance the quality of the engine
sound.
In addition, if the gear is shifted or the
accelerator pedal is quickly operated
when the transmission setup switch is in
R mode and the engine warmed up, a
sound effect is output to enhance the
sense of sportiness. (
“R mode” page
5-25)

Self-adjusting brakes ............................................... 8-19
Servicing air conditioner ....................................... 4-14
Setting (drive computer) ....................................... 2-20
Setting guide of wheel alignment
depending on the customer’s driving ........ 9-21
Setting hazard indicator and
horn mode ....................................................................... 3-14
Shift lever position warning ............................... 2-37
Shift “P” warning .......................................................... 2-46
Small children ................................................................ 1-14
Sonar system ................................................................. 5-48
Sonar system off switch ....................................... 2-59
Sonar system setting .............................................. 5-50
Spark plugs ...................................................................... 8-16
Special winter equipment .................................... 5-57
Specifications ................................................................. 10-9
Speedometer ...................................................................... 2-7
StartingBefore starting the engine ........................... 5-13
Jump starting ............................................. 6-5, 8-15
Precautions when starting
and driving ................................................................... 5-3
Push starting .............................................................. 6-8
Starting the engine ............................................ 5-14
Steering
Power steering ....................................................... 5-51
Power steering fluid .......................................... 8-11
Steering lock release
malfunction indicator ....................................... 2-47
Steering wheel ....................................................... 3-26
Steering-wheel-mounted controls ........ 5-36 Tilt/telescopic steering column ............... 3-26
Storage ............................................................................... 2-63
Summer tires ............................................................ GTR-11
Sun visors .......................................................................... 3-27
Sunglasses holder ...................................................... 2-64
Supplemental air bag warning labels ........ 1-48
Supplemental air bag warning light ............ 1-48
Supplemental restraint system ....................... 1-34
Suspension and
wheel alignment .............................. GTR-16, GTR-23
Switch Hazard warning flasher switch .................... 6-2
Headlight and turn signal switch ........... 2-53
Headlight switch ................................................... 2-53
How to switch the modes ............................ 5-26
Ignition switch operation .............................. 5-11
Ignition switch positions ................................ 5-11
Interior light control switch ......................... 2-70
Locking with power door lock switch ..... 3-5
Push-button ignition switch ....................... 5-10
Rear window defroster switch .................. 2-52
Trunk lid release switch ................................. 3-20
Trunk open request switch ......................... 3-20
Trunk release power cancel switch ...... 3-21
VDC, transmission and suspension
setup switches ....................................................... 5-25
Wiper and washer switch .............................. 2-51
T

Types of tires .......................................................... 8-36
Uniform tire quality grading ................... 10-20
Wheels and tires ................................ 8-29, 10-10
Tires and road wheels ......................................... GTR-5
Titanium muffler ....................................................... GTR-7
Change of surface color of
titanium muffler ............................................. GTR-30
Sound heard around
titanium muffler ............................................. GTR-30
To protect your vehicle from corrosion ....... 7-9
Towing
Flat towing ............................................................ 10-20
Towing a trailer ................................................. 10-19
Towing recommended by NISSAN ......... 6-10
Towing your vehicle ............................................. 6-9
Traction AA, A, B and C ....................................... 10-20
Transceiver HomeLink® Universal Transceiver .......... 2-71
Transmission
Dual clutch transmission ............................... 5-15
Transmission clutch high
temperature warning ....................................... 2-39
Transmission oil .................................. GTR-4, 8-10
Transmission oil high
temperature warning ....................................... 2-38
Transmission position indicator .............. 2-10
Transmission system check display ..... 2-15
Transmission system warning .................. 2-38
VDC, transmission and suspension
setup switches ....................................................... 5-25 Transmission assembly/parts
replacement record .................................................. 9-26
Transmission
operation characteristics ............................... GTR-32
Transmission settings .......................................... GTR-9
Treadwear ..................................................................... 10-20
Troubleshooting guide ........................................... 3-17
Trunk .................................................................................... 3-20
Trunk lid release switch ........................................ 3-20
Trunk open request switch ................................ 3-20
Trunk release power cancel switch ............. 3-21
Turbocharger system .............................................. 5-32
Turning off the heaters ......................................... 2-58
Turning on the heaters ......................................... 2-58
Types of tires ................................................................. 8-36
UV
W

Check the coolant level in the pressurized
coolant reservoir. Adjust the level so that
the fluid is between the MAX and MIN
markings. For the coolant, use genuine
NISSAN Long Life coolant or equivalent.
(On delivery of new vehicle, the reservoir
is filled to the MIN level. Be sure to
replenish approximately 3/8 US quart
(0.3 to 0.4 liter) of coolant.)
NOTICE
Do not overfill the coolant. This may
increase the pressure in the cooling
system and cause coolant leaks.
To maximize vehicle performance, the
coolant mixture ratio should be a combi-
nation of 30% coolant antifreeze and 70%
demineralized or distilled water for max-
imum cooling system performance re-
gardless of ambient temperatures.
If ambient temperatures are anticipated
below 5°F (−15°C), make sure a proper
mixture ratio of 50% antifreeze and 50%
demineralized or distilled water mix is
used.Engine and powertrainThe information and specifications in
this section apply only when engaging in performance driving.
.
Check the engine, transmission, differ-
ential and under the vehicle for oil and
coolant leaks.
. Inspect the areas surrounding of the
catalytic converter for heat deteriora-
tion.
. Always perform the transmission
setting. After that, adjust the clutch
clearance so that the clearance is less
than the clearance used for daily
driving. Your GT-R certified NISSAN
dealer has the necessary information
and equipment to set the clutch
clearance to the correct specification.
The clearance used for daily driving
increases clutch heat generated dur-
ing Performance Driving. This leads to
an increase in temperature of the
transmission oil. In addition, a more
direct shifting feel can be obtained by
reducing the clutch clearance for
Performance Driving. The clutch clear-
ance should be reset to the daily
driving specification after Perfor-
mance Driving. It is recommended
you see a GT-R certified NISSAN dealer
for information.
NOTICE
Failure to have the clutch properly
adjusted before performance driving
may cause the transmission oil tem-
perature to increase which may
cause transmission damage.
. Inspect and confirm the clearance
between the exhaust finisher and rear
bumper is more than 0.24 in (6 mm)
(up/down) and more than 0.20 in (5
mm) (left/right).
. Inspect the dust boot of the drive
shaft universal joint for cracks or
damage.Suspension and wheel alignmentThe information and specifications in
this section apply only when engaging
in performance driving.
.Check the steering and suspension
system and other links for loose and/
or damaged parts.
. Measure and adjust the wheel align-
ment. (
“Wheel alignment” page
GTR-10) It is recommended you con-
tact a GT-R certified NISSAN dealer to
adjust the wheel alignment to the
recommended setting for high perfor-

The Vehicle Dynamic Control (VDC) sys-
tem uses various sensors to monitor
driver inputs and vehicle motion. Under
certain driving conditions, the VDC sys-
tem helps to perform the following func-
tions.
.Controls brake pressure to reduce
wheel slip on one slipping drive wheel
so power is transferred to a non
slipping drive wheel on the same axle.
. Controls brake pressure and engine
output to reduce drive wheel slip
based on vehicle speed (traction con-
trol function).
. Controls brake pressure at individual
wheels and engine output to help the
driver maintain control of the vehicle
in the following conditions:
— understeer (vehicle tends to not
follow the steered path despite
increased steering input)
— oversteer (vehicle tends to spin due to certain road or driving condi-
tions).
The VDC system can help the driver to
maintain control of the vehicle, but it
cannot prevent loss of vehicle control in
all driving situations.
When the VDC system operates, the VDC
warning light
in the meter flashes so note the following:
.
The road may be slippery or the
system may determine some action
is required to help keep the vehicle on
the steered path.
. You may feel a pulsation in the brake
pedal and hear a noise or vibration
from under the hood. This is normal
and indicates that the VDC system is
working properly.
. Adjust your speed and driving to the
road conditions.
. The VDC mode can be changed using
the VDC setup switch. (
“VDC,
transmission and suspension setup
switches” page 5-25)
(
“Vehicle Dynamic Control (VDC)
warning light” page 2-34,
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
If a malfunction occurs in the system, the
VDC warning light
illuminates in the
meter. The VDC system automatically
turns off.
The VDC setup switch is used to turn off
the VDC system. The VDC off indicator
illuminates to indicate the VDC sys-
tem is off.
When the VDC setup switch is used to
turn off the system, the VDC system still
VEHICLE DYNAMIC CONTROL (VDC) SYSTEM