2022 NISSAN GT-R maintenance

SETTING (drive computer)This is used to set the alert, maintenance
and optional settings.
Use the NEXT switch
to select an
item, then confirm with the ENTER switch
to change to the corresponding
setting screen.
To return to the initial setting screen,
push and hold the ENTER switch
for
more than 1 second. NOTE:
.
When the battery terminal is discon-
nected, the set memory will be
erased and the settings return to
the default.
. Setting is not possible in the follow-
ing cases.
—The vehicle is being driven.
— A warning display is active.
— The instrument brightness con-
trol level display is active.
— The cruise control status is dis-
played.
AlertThis function can be used to make
settings for the upshift indicator, “time
to rest” indicator and low outside tem-
perature warning.
Upshift indicator:
For details concerning the upshift indica-
tor, refer to the following section.
(
“Upshift indicator” page 2-10)

to change the time. Push and
hold the switch to increase the number
every 1 hour. A maximum of 6 hours can
be set.
NOTE:
The default setting is OFF.
Low outside temperature warning:
This alert informs the driver when the
outside air temperature is lower than 37°F
(3°C).
On the ICY screen, push the NEXT switch
to turn this warning ON/OFF.
NOTE:
The default setting is ON.
MaintenanceThis function can be used to set the
various maintenance intervals and to
check the engine oil level. The reminders
shown below are used to notify the driver
of the maintenance intervals.
NOTE:
Because these are displayed based on
the mileage driven, they do not indicate
the actual conditions of the vehicle. Use
these functions only as a reference.
Input the maintenance distance using the
following items:
. On each setting screen, push the
Instruments and controls
2-21

to change the mile-
age. Push and hold the switch to
increase the number every 600 miles
(1,000 km).
. Set to “—” to set no reminders.
. To reset the accumulated mileage to
zero, go to the RESET screen, then
push the NEXT switch
and confirm
with the ENTER switch.
NOTE:
. To restore the mileage to the origi-
nal figure after resetting, push the
NEXT switch
again.
. When the battery terminal is discon-
nected, the set mileage will be
erased and the settings will return
to their default settings.
Engine oil level:
This can be used to check the pre-start oil
level while the engine is running. Select
SETTING > MAINTENANCE > OIL > ENGINE
OIL > LEVEL.
If the low level reminder appears, check
the level using the engine oil dipstick.
(
“Checking engine oil level” page 8-9)

Transmission oil:
The reminder is displayed when the
customer set mileage is exceeded. Select
SETTING > MAINTENANCE > OIL > T/M OIL
to set or reset the mileage for the
transmission oil change.
NOTE:
The default setting is 37,000 miles
(60,000 km). The maximum mileage
that can be set is 55,500 miles (90,000
km).
Tires:
This reminder appears when the custo-
mer set distance comes for maintaining
tires. You can set or reset the distance for
maintaining tires. (
“Setting (drive
computer)” page 2-20)

affect tire wear and when tires
should be replaced. Setting the tire
maintenance reminder for a certain
driving distance does not mean your
tires will last that long. Use the tire
maintenance reminder as a guide
only and always perform regular tire
checks. Failure to perform regular
tire checks, including tire pressure
checks could result in tire failure.
Serious vehicle damage could occur
and may lead to a collision, which
could result in serious personal in-
jury or death.
NOTE:
The default setting is OFF.
OptionsThis function can be used to make
settings for language and unit.
Language:
Select ENGLISH or FRANCAIS for use in the
vehicle information display.
Unit:
Select METRIC or US for use in the vehicle
information display.
while a
warning display is active to return to the
original display.
It is also possible to check any warnings
that have not been corrected.
(
“Warning display” page 2-36)
Checking the warningsUse the NEXT switch
to select “DE-
TAIL”, then confirm with the ENTER switch
.
When there are multiple warnings, push

NOTE:
.If the vehicle is being driven at
speeds of less than 16 MPH (25
km/h), the TPMS may not operate
correctly.
. The tires of this vehicle are filled
with nitrogen gas. When the tire
pressure is low, fill the tires with
nitrogen gas. It is recommended you
contact a GT-R certified NISSAN
dealer for information on filling the
tires with nitrogen gas.
light
should turn off if no other potential
emission control system malfunction ex-
ists. If this indicator light remains on for 20
seconds and then blinks for 10 seconds
when the engine is not running, it indi-
cates that the vehicle is not ready for an
emission control system inspection/
maintenance test. (
“Readiness for
Inspection/Maintenance (I/M) test (US
only)” page 10-22)
Operation:
The malfunction indicator light will come
on in one of two ways:
. Malfunction indicator light on steady
— An emission control system mal-
function has been detected. Check
the fuel-filler cap. If the fuel-filler cap
is loose or missing, tighten or install
the cap and continue to drive the
vehicle. The
light should turn off
after a few driving trips. If the
light
does not turn off after a few driving
trips, it is recommended you have the
vehicle inspected by a GT-R certified
NISSAN dealer. You do not need to
have your vehicle towed to the dealer.
. Malfunction indicator light blinking —
An engine misfire has been detected
which may damage the emission
control system.
To reduce or avoid emission control
system damage: 1) Do not drive at speeds above 45
MPH (72 km/h).
2) Avoid hard acceleration or decel- eration.
3) Avoid steep uphill grades.
4) If possible, reduce the amount of cargo being hauled or towed.
The malfunction indicator light may
stop blinking and remain on.
It is recommended you have the
vehicle inspected by a GT-R certified
NISSAN dealer. You do not need to
have your vehicle towed to the dealer.
NOTICE
Continued vehicle operation without
having the emission control system
checked and repaired as necessary
could lead to poor driveability, re-
duced fuel economy, and possible
damage to the emission control sys-
tem.
Master warning light
When the ignition switch is in the ON
position, the master warning light illumi-
nates if any of the warning displays
appear on the vehicle information display.
(
“Warning display” page 2-36)

is used.
. Objects in the RearView Monitor
will appear visually opposite
compared to when viewed in the
rearview and outside mirrors.
. Use the displayed lines as a re-
ference. The lines are highly af-
fected by the number of
occupants, fuel level, vehicle po-
sition, road conditions and road
grade.
. Make sure that the trunk lid is
securely closed when backing up.
. Do not put anything on the rear-
view camera. The rearview cam-
era is installed above the license
plate.
. When washing the vehicle with
high-pressure water, be sure not
to spray it around the camera.
Otherwise, water may enter the
camera unit causing water con-
densation on the lens, a malfunc-
tion, fire or an electric shock.
. Do not strike the camera. It is a
precision instrument. Otherwise,
it may malfunction or cause da-
mage resulting in a fire or an
electric shock. The following are operating limitations
and do not represent a system malfunc-
tion:
.
When the temperature is extremely
high or low, the screen may not clearly
display objects.
. When strong light is directly coming
on the camera, objects may not be
displayed clearly.
. Vertical lines may be seen in objects
on the screen. This is due to strong
reflected light from the bumper.
. The screen may flicker under fluores-
cent light.
. The colors of objects on the RearView
Monitor may differ somewhat from
the actual color of objects.
. Objects on the monitor may not be
clear in a dark environment.
. There may be a delay when switching
to the RearView Monitor screen.
. If dirt, rain or snow accumulates on
the camera, the RearView Monitor
may not display objects clearly. Clean
the camera.
. Do not use wax on the camera win-
dow. Wipe off any wax with a clean
cloth dampened with mild detergent
diluted with water.
SYSTEM MAINTENANCE
CAUTION
.Do not use alcohol, benzine or
thinner to clean the camera. This
will cause discoloration. To clean
the camera, wipe with a cloth
dampened with diluted mild
cleaning agent and then wipe
with a dry cloth.
. Do not damage the camera as the
monitor screen may be adversely
affected.

and
located on the
instrument panel help maintain a con-
stant temperature. Do not put anything
on or around the sensors.
IN-CABIN MICROFILTERThe air conditioning system is equipped
with an in-cabin microfilter which collects
dirt, dust, etc. To make sure the air
conditioner heats, defogs, and ventilates
efficiently, replace the filter in accordance
with the maintenance schedule in the “9.
Maintenance and schedules” section of
this manual. It is recommended to see a
NISSAN dealer or GT-R certified NISSAN
dealer to replace the filter.
The filter should be replaced if air flow
is extremely decreased or when win-
dows fog up easily when operating
heater or air conditioning system.
Display screen, heater, air conditioner and audio systems
4-13