2022 NISSAN GT-R flat tire

being uninstalled from the
wheels, use equipment such as a
leverless automatic tire changer.
It is only possible to reuse the
tires when they have no cracks
and/or deformations on the bead
portion. However, if you use a
lever-type tire changer, cracks
and deformation may occur on
the bead portion of the tires
meaning that the tires cannot be
reused.
. Make sure the tire valve stem cap
is installed and that the valve
stem is tight. When installing the
cap, make sure to tighten the cap
by hand. If a tool is used to
tighten the cap, the cap may be
damaged.
WARNING
.The use of tires other than those
specified or the mixed use of tires
of different brands, construction
(bias, bias-belted, radial or run-
flat), or tread patterns can ad-
versely affect the ride, braking,
VDC system, handling, ground
clearance, body-to-tire clearance, tire chain clearance, speed-
ometer calibration, headlight
aim and bumper height. Some of
these effects may lead to acci-
dents and could result in serious
personal injury.
. If the wheels are changed for any
reason, always replace with
wheels which have the same off-
set dimension. Wheels of a differ-
ent off-set could cause prema-
ture tire wear, degrade vehicle
handling characteristics, affect
the VDC system and/or cause
interference with the brake discs.
Such interference can lead to
decreased braking efficiency
and/or early brake pad wear.
(
“Wheels and tires” page 10-
10)
. When a wheel is replaced, tire
pressure will not be indicated,
the TPMS will not function and
the low tire pressure warning
light will flash for approximately
1 minute and remain on after the
1 minute. It is recommended you
contact a GT-R certified NISSAN
dealer as soon as possible for tire
replacement and/or system re-
setting. .
Replacing tires with those not
originally specified by NISSAN
could affect the proper operation
of the TPMS.
. The TPMS sensor may be da-
maged if it is not handled cor-
rectly. Be careful when handling
the TPMS sensor.
. When replacing the TPMS sensor,
the ID registration may be re-
quired. Contact a GT-R certified
NISSAN dealer for ID registration.
. Do not use a valve stem cap that
is not specified by NISSAN. The
valve stem cap may become
stuck.
. Be sure that the valve stem caps
are correctly fitted. Otherwise the
valve may be clogged up with dirt
and cause a malfunction or loss
of pressure.
. Do not install a damaged or
deformed wheel or tire even if it
has been repaired. Such wheels
or tires could have structural
damage and could fail without
warning.
. Never use retread tires.
. For additional information re-

garding tires, refer to “Important
Tire Safety Information” (US) or
“Tire Safety Information” (Cana-
da) in the Warranty Information
Booklet.
. Always use tires of the specified
type, size, brand, construction
(bias, bias-belted, radial or run-
flat), and tread pattern on all four
wheels. Failure to do so may
result in a circumference differ-
ence between tires on the front
and rear axles which will cause
excessive tire wear and may da-
mage the transmission, transfer
case and differential gears.
Wheel balanceUnbalanced wheels may affect vehicle
handling and tire life. Even with regular
use, wheels can get out of balance.
Therefore, they should be balanced as
required.
Wheel balance service should be per-
formed with the wheels off the vehicle.
Spin balancing the rear wheels on the
vehicle could lead to mechanical damage.
For additional information regarding tires,
refer to “Important Tire Safety Informa-
tion” (US) or “Tire Safety Information” (Canada) in the Warranty Information
Booklet.
Care of wheels(
“Cleaning exterior” page 7-2)
JACKING VEHICLE AND REMOVING
WHEELS
WARNING
.
Make sure the parking brake is
securely applied and the trans-
mission is shifted into the
position.
. Never change tires when the ve-
hicle is on a slope, ice or slippery
areas. This is hazardous.
. Never change tires if oncoming
traffic is close to your vehicle.
Wait for professional road assis-
tance.
Blocking wheelsPlace suitable blocks
at both the front
and back of the wheel diagonally oppo-
site the flat tire to prevent the vehicle
from moving when it is jacked up.

VEHICLE LOAD CAPACITY
Do not exceed the load limit of your
vehicle shown as “The combined
weight of occupants and cargo” on
the Tire and Loading Information
label. Do not exceed the number of
occupants shown as “Seating Ca-
pacity” on the Tire and Loading
Information label.
To get “the combined weight of
occupants and cargo”, add the
weight of all occupants, then add
the total luggage weight. Examples
are shown in the illustration.
Steps for determining correct
load limit1.
Locate the statement “The com-
bined weight of occupants and
cargo should never exceed XXX
kg or XXX lbs” on your vehicle’s
placard.
2.
Determine the combined weight
of the driver and passengers
that will be riding in your vehicle.
3.
Subtract the combined weightof the driver and passengers
from XXX kg or XXX lbs.
4.
The resulting figure equals the
available amount of cargo and
luggage load capacity. For ex-
ample, if the XXX amount equals
1400 lbs. and there will be five
150 lb. passengers in your vehi-
cle, the amount of available
cargo and luggage load capacity
is 650 lbs. (1400 − 750 (5 x 150) =
650 lbs) or 640 − 340 (5 x 70) =
300 kg.)
5.
Determine the combined weight
of luggage and cargo being
loaded on the vehicle. That
weight may not safely exceed
the available cargo and luggage
load capacity calculated in Step
4.
6.
If your vehicle will be towing a
trailer, load from your trailer will
be transferred to your vehicle.
Consult this manual to deter-
mine how this reduces the avail-
able cargo and luggage loadcapacity of your vehicle.
Before driving a loaded vehicle,
confirm that you do not exceed
the Gross Vehicle Weight Rating
(GVWR) or the Gross Axle Weight
Rating (GAWR) for your vehicle.
(
“Measurement of weights”
page 10-19)
Also check tires for proper inflation
pressures. See the Tire and Loading
Information label.
LOADING TIPS
.
The GVW must not exceed GVWR
or GAWR as specified on the F.M.
V.S.S./C.M.V.S.S. certification la-
bel.
.
Do not load the front and rear
axle to the GAWR. Doing so will
exceed the GVWR.

Types of tires .......................................................... 8-36
Uniform tire quality grading ................... 10-20
Wheels and tires ................................ 8-29, 10-10
Tires and road wheels ......................................... GTR-5
Titanium muffler ....................................................... GTR-7
Change of surface color of
titanium muffler ............................................. GTR-30
Sound heard around
titanium muffler ............................................. GTR-30
To protect your vehicle from corrosion ....... 7-9
Towing
Flat towing ............................................................ 10-20
Towing a trailer ................................................. 10-19
Towing recommended by NISSAN ......... 6-10
Towing your vehicle ............................................. 6-9
Traction AA, A, B and C ....................................... 10-20
Transceiver HomeLink® Universal Transceiver .......... 2-71
Transmission
Dual clutch transmission ............................... 5-15
Transmission clutch high
temperature warning ....................................... 2-39
Transmission oil .................................. GTR-4, 8-10
Transmission oil high
temperature warning ....................................... 2-38
Transmission position indicator .............. 2-10
Transmission system check display ..... 2-15
Transmission system warning .................. 2-38
VDC, transmission and suspension
setup switches ....................................................... 5-25 Transmission assembly/parts
replacement record .................................................. 9-26
Transmission
operation characteristics ............................... GTR-32
Transmission settings .......................................... GTR-9
Treadwear ..................................................................... 10-20
Troubleshooting guide ........................................... 3-17
Trunk .................................................................................... 3-20
Trunk lid release switch ........................................ 3-20
Trunk open request switch ................................ 3-20
Trunk release power cancel switch ............. 3-21
Turbocharger system .............................................. 5-32
Turning off the heaters ......................................... 2-58
Turning on the heaters ......................................... 2-58
Types of tires ................................................................. 8-36
UV
W

being uninstalled from the
wheels, use equipment such as a
leverless automatic tire changer.
It is only possible to reuse the
tires when they have no cracks
and/or deformations on the bead
portion. However, if you use a
lever-type tire changer, cracks
and deformation may occur on
the bead portion of the tires
meaning that the tires cannot be
reused.
. Make sure the tire valve stem cap
is installed and that the valve
stem is tight. When installing the
cap, make sure to tighten the cap
by hand. If a tool is used to
tighten the cap, the cap may be
damaged.
WARNING
.The use of tires other than those
specified or the mixed use of tires
of different brands, construction
(bias, bias-belted, radial or run-
flat), or tread patterns can ad-
versely affect the ride, braking,
VDC system, handling, ground
clearance, body-to-tire clearance, tire chain clearance, speed-
ometer calibration, headlight
aim and bumper height. Some of
these effects may lead to acci-
dents and could result in serious
personal injury.
. If the wheels are changed for any
reason, always replace with
wheels which have the same off-
set dimension. Wheels of a differ-
ent off-set could cause prema-
ture tire wear, degrade vehicle
handling characteristics, affect
the VDC system and/or cause
interference with the brake discs.
Such interference can lead to
decreased braking efficiency
and/or early brake pad wear.
(
“Wheels and tires” page 10-
10)
. When a wheel is replaced, tire
pressure will not be indicated,
the TPMS will not function and
the low tire pressure warning
light will flash for approximately
1 minute and remain on after the
1 minute. It is recommended you
contact a GT-R certified NISSAN
dealer as soon as possible for tire
replacement and/or system re-
setting. .
Replacing tires with those not
originally specified by NISSAN
could affect the proper operation
of the TPMS.
. The TPMS sensor may be da-
maged if it is not handled cor-
rectly. Be careful when handling
the TPMS sensor.
. When replacing the TPMS sensor,
the ID registration may be re-
quired. Contact a GT-R certified
NISSAN dealer for ID registration.
. Do not use a valve stem cap that
is not specified by NISSAN. The
valve stem cap may become
stuck.
. Be sure that the valve stem caps
are correctly fitted. Otherwise the
valve may be clogged up with dirt
and cause a malfunction or loss
of pressure.
. Do not install a damaged or
deformed wheel or tire even if it
has been repaired. Such wheels
or tires could have structural
damage and could fail without
warning.
. Never use retread tires.
. For additional information re-

garding tires, refer to “Important
Tire Safety Information” (US) or
“Tire Safety Information” (Cana-
da) in the Warranty Information
Booklet.
. Always use tires of the specified
type, size, brand, construction
(bias, bias-belted, radial or run-
flat), and tread pattern on all four
wheels. Failure to do so may
result in a circumference differ-
ence between tires on the front
and rear axles which will cause
excessive tire wear and may da-
mage the transmission, transfer
case and differential gears.
Wheel balanceUnbalanced wheels may affect vehicle
handling and tire life. Even with regular
use, wheels can get out of balance.
Therefore, they should be balanced as
required.
Wheel balance service should be per-
formed with the wheels off the vehicle.
Spin balancing the rear wheels on the
vehicle could lead to mechanical damage.
For additional information regarding tires,
refer to “Important Tire Safety Informa-
tion” (US) or “Tire Safety Information” (Canada) in the Warranty Information
Booklet.
Care of wheels(
“Cleaning exterior” page 7-2)
JACKING VEHICLE AND REMOVING
WHEELS
WARNING
.
Make sure the parking brake is
securely applied and the trans-
mission is shifted into the
position.
. Never change tires when the ve-
hicle is on a slope, ice or slippery
areas. This is hazardous.
. Never change tires if oncoming
traffic is close to your vehicle.
Wait for professional road assis-
tance.
Blocking wheelsPlace suitable blocks
at both the front
and back of the wheel diagonally oppo-
site the flat tire to prevent the vehicle
from moving when it is jacked up.

or
position: The maximum
engine speed is 4,300 RPM
. Revving the engine when the engine
oil is at a low (below 32°F (0°C)) or
extremely high (over 275°F (135°C))
temperature: The maximum engine
speed is 4,000 RPM (The
position
will automatically change to the
position.)
ENGINE OUTPUT
High altitudeTo protect the engine, engine output is
controlled so that it does not increase at
altitude of approximately 3,281 ft (1,000
m) or higher.Engine output according to the
coolant temperatureThe engine output is controlled at a low
level when the engine coolant tempera-
ture is lower than approximately 158°F
(70°C) or higher than 230°F (110°C). This is
not a malfunction. If the temperature is lower than approxi-
mately 158°F (70°C), drive the vehicle until
it reaches normal operating temperature.
If the temperature is higher than 230°F
(110°C), perform cool-down driving proce-
dure. (
“Cool down” page GTR-14)
When the temperature of the engine
coolant is between 158°F (70°C) and
230°F (110°C), the engine output returns
to normal.
UNEVEN WEAR OF TIRESThe GT-R is equipped with high perfor-
mance, low profile, run-flat tires that are
optimized for performance and handling.
The life of these tires will be less than
those of tires installed on a typical vehicle,
and you are likely to experience uneven
tire wear and tire noise regardless of the
type of tire used.NOISES ARE HEARD WHILE DRIV-
ING

Intelligent Key warning light
After the ignition switch is pushed to the
ON position, this light comes on for about
2 seconds and then turns off.
This light warns of a malfunction with the
electrical steering lock system or the
Intelligent Key system.
If the light comes on while the engine is
stopped, it may be impossible to free the
steering lock or to start the engine. If the
light comes on while the engine is run-
ning, you can drive the vehicle. However
in these cases, it is recommended you
contact a GT-R certified NISSAN dealer for
repair as soon as possible.
“Tire
Pressure Monitoring System (TPMS)”
page 5-4) (
“Tire Pressure Monitor-
ing System (TPMS)” page 6-3)
Run-flat tire warning:
“Run-flat tires” page 8-36)
TPMS malfunction:
If the TPMS is not functioning properly,
the low tire pressure warning light will
flash for approximately 1 minute when the
ignition switch is pushed to the ON
position. The light will remain on after
the 1 minute. It is recommended you have
the system checked by a GT-R certified
NISSAN dealer. (
“Tire Pressure Mon-
itoring System (TPMS)” page 5-4)
(
“Tire pressure” page 8-30)