2022 NISSAN GT-R change time

another GT-R are installed on
your vehicle.
. The TPMS will not function prop-
erly if non-GT-R wheels are in-
stalled on the vehicle.
. Do not place metalized film or
any metal parts (antenna, etc.) on
the windows. This may cause
poor reception of the signals
from the tire pressure sensors,
and the TPMS will not function
properly.
Some devices and transmitters may tem-
porarily interfere with the operation of
the TPMS and cause the low tire pressure
warning light to illuminate. Some exam-
ples are:
. Facilities or electric devices using
similar radio frequencies are near the
vehicle.
. If a transmitter set to similar frequen-
cies is being used in or near the
vehicle.
. If a computer (or similar equipment) or
a DC/AC converter is being used in or
near the vehicle.
Low tire pressure warning light may
illuminate in the following cases. .
If the vehicle is equipped with a wheel
and tire without TPMS.
. If the TPMS has been replaced and the
ID has not been registered.
. If the wheel is not originally specified
by NISSAN.
FCC Notice:
For USA:
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept any
interference received, including inter-
ference that may cause undesired op-
eration.
Note: Changes or modifications not
expressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Ca-
nada licence-exempt RSS standard(s).
Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation of the device.
WARNING
Failure to operate this vehicle in a
safe and prudent manner may result
in loss of control or an accident.
Be alert and drive defensively at all times.
Obey all traffic regulations. Avoid exces-
sive speed, high speed cornering, or
sudden steering maneuvers, because
these driving practices could cause you
to lose control of your vehicle. As with
any vehicle, a loss of control could
result in a collision with other vehicles
or objects, or cause the vehicle to roll-
over, particularly if the loss of control
causes the vehicle to slide sideways. Be
attentive at all times, and avoid driving
when tired. Never drive when under the
influence of alcohol or drugs (including
prescription or over-the-counter drugs
which may cause drowsiness). Always
wear your seat belt as outlined in this
manual, and also instruct your passen-
gers to do so. (

dually stop the vehicle.
6. Turn on the hazard warning flashers and contact a roadside emergency
service to change the tire.
DRINKING ALCOHOL/DRUGS AND
DRIVING
WARNING
Never drive under the influence of
alcohol or drugs. Alcohol in the
bloodstream reduces coordination,
delays reaction time and impairs
judgement. Driving after drinking
alcohol increases the likelihood of
being involved in an accident injuring
yourself and others. Additionally, if
you are injured in an accident, alco-
hol can increase the severity of the
injury.
NISSAN is committed to safe driving.
However, you must choose not to drive
under the influence of alcohol. Every year
thousands of people are injured or killed
in alcohol-related accidents. Although the
local laws vary on what is considered to
be legally intoxicated, the fact is that
alcohol affects all people differently and
most people underestimate the effects of alcohol.
Remember, drinking and driving don’t
mix! And that is true for drugs, too (over-
the-counter, prescription, and illegal
drugs). Don’t drive if your ability to oper-
ate your vehicle is impaired by alcohol,
drugs, or some other physical condition.
ALL-WHEEL DRIVE (AWD) DRIVING
SAFETY PRECAUTIONS
WARNING
.
Do not drive beyond the perfor-
mance capability of the tires,
even with AWD engaged. Acceler-
ating quickly, sharp steering
maneuvers or sudden braking
may cause loss of control.
. Always use the specified tires on
all four wheels. Install tire chains
on the rear wheels when driving
on slippery roads and drive care-
fully.
. This vehicle is not designed for
offroad (rough road) use. Do not
drive on sandy or muddy roads
that tires may get stuck in.
. Do not attempt to raise two
wheels off the ground and shift the transmission to any
position with the engine run-
ning. Doing so may result in
drivetrain damage or unexpected
vehicle movement which could
result in serious vehicle damage
or personal injury.
. Do not attempt to test an AWD
equipped vehicle on a 2-wheel
dynamometer, (such as the dy-
namometers used by some
states for emissions testing), or
similar equipment even if the
other two wheels are raised off
the ground. Make sure you inform
test facility personnel that your
vehicle is equipped with AWD
before it is placed on a dynam-
ometer. Using the wrong test
equipment may result in drive-
train damage or unexpected ve-
hicle movement which could
result in serious vehicle damage
or personal injury.
. When a wheel is off the ground
due to an unlevel surface, do not
spin the wheel excessively.
Starting and driving
5-9

position, and to
4,000 rpm when the engine oil or
coolant temperature is low or higher
than normal.
. If the ignition switch is pushed
before the shift lever is moved to
the
position, the ignition switch
will not change to the OFF position.
If this occurs, the SHIFT
warning
display appears on the vehicle in-
formation display. When stopping
the engine, be sure to move the shift
lever to the
position and then
push the ignition switch. Failure to
do so may result in discharge of the
battery. (“Shift “P” warning”
page 2-46)
. If the shift lever was in the
position when the engine was
stopped, then be sure to move the
shift lever to the
position before
starting the engine the next time. If the engine is started with the shift
lever in the
position, then it may
not be possible to drive the vehicle
even when the shift lever is moved
to the
position. If this
occurs, the SHIFTwarning appears
on the vehicle information display.
(
“Shift “P” warning” page 2-46)
CAUTION
If the engine was stopped soon
when the engine is hot, the cooling
fan may operate for approximately 2
minutes after the engine was
stopped to cool the components in
the engine compartment. When the
cooling fan is operating, be sure that
hands or other items do not get
caught in it.
DUAL CLUTCH TRANSMISSIONThe GT-R dual clutch transmission is a
newly-developed system that uses an
electronically controlled multiple-disc
wet clutch attached to the highly efficient
manual transmission. This transmission
has two driving modes.
.
position
and operate the paddle shifter to shift
down to 1st gear similar to a manual
transmission vehicle.
The GT-R dual clutch transmission was
developed specifically to maximize vehi-
cle performance and driving enjoyment.
The GT-R transmission components were
designed using different engineering
standards than typical passenger car
transmissions. Because of this, the GT-R
has different operating characteristics,
and various rattle noises may be heard
during some driving conditions because
Starting and driving
5-15
DRIVING THE VEHICLE

.ALWAYS use your seat belts and
appropriate child restraint sys-
tems. Pre-teen children should
be seated in the rear seat.
. ALWAYS provide information
about the proper use of vehicle
safety features to all occupants
of the vehicle.
. ALWAYS review this Owner’s Man-
ual for important safety informa-
tion.MODIFICATION OF YOUR VEHICLEThis vehicle should not be modified.
Modification could affect its perfor-
mance, safety or durability, and may
even violate governmental regulations.
See the 2021 NISSAN GT-R Warranty
Information Booklet for details includ-
ing applicable exclusions.
WARNING
Installing an aftermarket On-Board
Diagnostic (OBD) plug-in device that
uses the port during normal driving,
for example remote insurance com-
pany monitoring, remote vehicle di-
agnostics, telematics or engine
reprogramming, may cause interfer- ence or damage to vehicle systems.
We do not recommend or endorse
the use of any aftermarket OBD
plug-in devices, unless specifically
approved by NISSAN. The vehicle
warranty may not cover damage
caused by any aftermarket plug-in
device.
WHEN READING THE MANUALThis manual includes information for all
features and equipment available on
this model. Features and equipment in
your vehicle may vary depending on
model, trim level, options selected, or-
der, date of production, region or avail-
ability. Therefore, you may find
information about features or equip-
ment that are not included or installed
on your vehicle.
All information, specifications and illustra-
tions in this manual are those in effect at
the time of printing. NISSAN reserves the
right to change specifications, perfor-
mance, design or component suppliers
without notice and without obligation.
From time to time, NISSAN may update
or revise this manual to provide owners
with the most accurate information cur-
rently available. Please carefully read and
retain with this manual all revision up-
dates sent to you by NISSAN to ensure
you have access to accurate and up-to-
date information regarding your vehicle.
Current versions of vehicle Owner’s Man-
uals and any updates can also be found in
the Owner section of the NISSAN website
at https://owners.nissanusa.com/now-
ners/navigation/manualsGuide. If you
have questions concerning any informa-
tion in your Owner’s Manual, contact
NISSAN Consumer Affairs. See the NISSAN
CUSTOMER CARE PROGRAM page in this
Owner’s Manual for contact information.
IMPORTANT INFORMATION ABOUT
THIS MANUALYou will see various symbols in this
manual. They are used in the following
ways:

to go to ALERT > UPSHIFT. The
current status of the upshift indicator will
be shown on the UPSHIFT screen. Note
that the function is set to AUTO as the
factory default setting.
To change the upshift indicator mode,
choose SETTING on the UPSHIFT screen.
Set one of the following modes by push-
ing the NEXT switch
, and then push
ENTER
to complete.
. AUTO
. 3,000 to 6,300 RPM (MANUAL)
. OFF
The number will increase by 100 RPM. To
increase the number by 500 RPM, push
and hold the NEXT switch
.
ExampleWhen the maximum engine speed is
desired:
Set the upshift indicator to AUTO. The
yellow indicator illuminates approxi-
mately 700 RPM before the red zone,
and the red indicator illuminates just
before the red zone.
When the maximum engine torque is
desired:
Set the figure at 6,000 RPM. The green
indicator starts flashing from approxi- mately 5,500 RPM and illuminates at
6,000 RPM.
When breaking-in the vehicle:
To help avoid high engine speeds during
break-in, set the upshift indicator to less
than 3,500 RPM. The green indicator
starts flashing approximately 500 RPM
before the set figure and illuminates from
the set figure. (
“Break-in schedule”
page 5-40)
NOTE:
. There may be a slight difference
between the timing of the upshift
indicator illumination and the tach-
ometer indication.
. When the battery terminal is discon-
nected, the set memory will be
erased and the mode returns to the
default.
INSTRUMENT BRIGHTNESS CON-
TROLThe instrument brightness can be ad-
justed when the ignition switch is in the
ON position. Push the switch to adjust the
brightness up
or down
. The bright-
ness level is shown on the vehicle infor-
mation display.
When the headlights are on, the bright-
ness of the interior switches is also
adjusted at the same time.

position. Operate the shift lever after
the system check indicator turns off.
. The shift lever cannot be moved if
the shift lever button is pushed
while the system check is being performed, even after the system
check is finished. Release the button
and push it again to operate the
shift lever.
. During winter or at other times when
the temperature is extremely low,
changes in the hydraulic response
characteristics may increase the
amount of time that is required for
the system check. During the system
check, a thudding operating noise
may occur or the engine speed may
decrease, however this does not
indicate that there is a malfunction.
Instruments and controls
2-15

2. NEXT switch3. Vehicle information displayThe drive computer displays the following
information:
.Current fuel consumption
. Vehicle speed
. Cruise control
. Average fuel consumption and speed
. Elapsed time and trip computer
. Distance to empty
. Outside air temperature
. Setting .
Warning
The vehicle information display
can be
changed when the ignition switch is in
the ON position. Push the ENTER switch
to change the display.
NOTE:
. The cruise control display is shown if
cruise control is set. (
“Cruise
control” page 5-35)
. The warning display is not shown if
there are no conditions to warn the
driver.
. Depending on the driving conditions
and other factors, the displayed
values may differ from the actual
values.
. The position of the speedometer
needle and the speed shown in the
vehicle information display may
slightly differ.
CURRENT FUEL CONSUMPTIONThe current fuel economy is displayed
when driving.
DRIVE COMPUTER

SETTING (drive computer)This is used to set the alert, maintenance
and optional settings.
Use the NEXT switch
to select an
item, then confirm with the ENTER switch
to change to the corresponding
setting screen.
To return to the initial setting screen,
push and hold the ENTER switch
for
more than 1 second. NOTE:
.
When the battery terminal is discon-
nected, the set memory will be
erased and the settings return to
the default.
. Setting is not possible in the follow-
ing cases.
—The vehicle is being driven.
— A warning display is active.
— The instrument brightness con-
trol level display is active.
— The cruise control status is dis-
played.
AlertThis function can be used to make
settings for the upshift indicator, “time
to rest” indicator and low outside tem-
perature warning.
Upshift indicator:
For details concerning the upshift indica-
tor, refer to the following section.
(
“Upshift indicator” page 2-10)