2022 NISSAN GT-R wheel

ways use run-flat tires of the specified
size on all four wheels. Mixing tire sizes or
construction may reduce vehicle handling
stability. If necessary, contact a GT-R
certified NISSAN dealer for assistance.
Frequently check the tire pressure infor-
mation on the touch screen display and
adjust pressure of each tire properly. See
the separate Multi Function Display Own-
er’s Manual.
It can be difficult to tell if a run-flat tire is
under-inflated or flat. Check the tire
pressures as described earlier in this
section. If the tire becomes under-inflated
while driving, the low tire pressure warn-
ing light will come on. If the tire becomes
flat while driving, the low tire pressure
warning light and the run-flat tire warn-
ing display will come on.
Low tire pressure:
NOTICE
.Never install tire chains on a
punctured run-flat tire, as this
could damage your vehicle.
. Avoid driving over any projection
or pothole, as the clearance be-
tween the vehicle and the ground
is smaller than normal.
. Do not enter an automated car
wash with a punctured run-flat
tire.
. It is recommended you have the
punctured tire replaced by a GT-R
certified NISSAN dealer as soon
Do-it-yourself
8-37

being uninstalled from the
wheels, use equipment such as a
leverless automatic tire changer.
It is only possible to reuse the
tires when they have no cracks
and/or deformations on the bead
portion. However, if you use a
lever-type tire changer, cracks
and deformation may occur on
the bead portion of the tires
meaning that the tires cannot be
reused.
. Make sure the tire valve stem cap
is installed and that the valve
stem is tight. When installing the
cap, make sure to tighten the cap
by hand. If a tool is used to
tighten the cap, the cap may be
damaged.
WARNING
.The use of tires other than those
specified or the mixed use of tires
of different brands, construction
(bias, bias-belted, radial or run-
flat), or tread patterns can ad-
versely affect the ride, braking,
VDC system, handling, ground
clearance, body-to-tire clearance, tire chain clearance, speed-
ometer calibration, headlight
aim and bumper height. Some of
these effects may lead to acci-
dents and could result in serious
personal injury.
. If the wheels are changed for any
reason, always replace with
wheels which have the same off-
set dimension. Wheels of a differ-
ent off-set could cause prema-
ture tire wear, degrade vehicle
handling characteristics, affect
the VDC system and/or cause
interference with the brake discs.
Such interference can lead to
decreased braking efficiency
and/or early brake pad wear.
(
“Wheels and tires” page 10-
10)
. When a wheel is replaced, tire
pressure will not be indicated,
the TPMS will not function and
the low tire pressure warning
light will flash for approximately
1 minute and remain on after the
1 minute. It is recommended you
contact a GT-R certified NISSAN
dealer as soon as possible for tire
replacement and/or system re-
setting. .
Replacing tires with those not
originally specified by NISSAN
could affect the proper operation
of the TPMS.
. The TPMS sensor may be da-
maged if it is not handled cor-
rectly. Be careful when handling
the TPMS sensor.
. When replacing the TPMS sensor,
the ID registration may be re-
quired. Contact a GT-R certified
NISSAN dealer for ID registration.
. Do not use a valve stem cap that
is not specified by NISSAN. The
valve stem cap may become
stuck.
. Be sure that the valve stem caps
are correctly fitted. Otherwise the
valve may be clogged up with dirt
and cause a malfunction or loss
of pressure.
. Do not install a damaged or
deformed wheel or tire even if it
has been repaired. Such wheels
or tires could have structural
damage and could fail without
warning.
. Never use retread tires.
. For additional information re-

garding tires, refer to “Important
Tire Safety Information” (US) or
“Tire Safety Information” (Cana-
da) in the Warranty Information
Booklet.
. Always use tires of the specified
type, size, brand, construction
(bias, bias-belted, radial or run-
flat), and tread pattern on all four
wheels. Failure to do so may
result in a circumference differ-
ence between tires on the front
and rear axles which will cause
excessive tire wear and may da-
mage the transmission, transfer
case and differential gears.
Wheel balanceUnbalanced wheels may affect vehicle
handling and tire life. Even with regular
use, wheels can get out of balance.
Therefore, they should be balanced as
required.
Wheel balance service should be per-
formed with the wheels off the vehicle.
Spin balancing the rear wheels on the
vehicle could lead to mechanical damage.
For additional information regarding tires,
refer to “Important Tire Safety Informa-
tion” (US) or “Tire Safety Information” (Canada) in the Warranty Information
Booklet.
Care of wheels(
“Cleaning exterior” page 7-2)
JACKING VEHICLE AND REMOVING
WHEELS
WARNING
.
Make sure the parking brake is
securely applied and the trans-
mission is shifted into the
position.
. Never change tires when the ve-
hicle is on a slope, ice or slippery
areas. This is hazardous.
. Never change tires if oncoming
traffic is close to your vehicle.
Wait for professional road assis-
tance.
Blocking wheelsPlace suitable blocks
at both the front
and back of the wheel diagonally oppo-
site the flat tire to prevent the vehicle
from moving when it is jacked up.

of
the jack-up point by turning the jack-
screw clockwise with your fingers.
3. Loosen each wheel nut one or two turns by turning counterclockwise
with the wheel nut wrench. Do not
remove the wheel nuts until the tire
is off the ground.
Do-it-yourself
8-43

5. Remove the wheel nuts and thenremove the wheel.
NOTE:
When putting a wheel on the
ground, put it down with the outer
side of the wheel facing up to pre-
vent scratching of the wheel surface.
and wheel
.

of each nut lightly
contacts the seat part
of the wheel
hole.
When replacing a front wheel, make
sure the hole in the wheel is aligned
with the pin on the brake disc rotor.
8. With the wheel nut wrench, tighten wheel nuts alternately and evenly in
the sequence illustrated (
,
,
,
,
)
until they are tight.
9. Lower the vehicle slowly until the tire touches the ground. Then, with the
wheel nut wrench, tighten the wheel
nuts securely in the sequence as
illustrated. Lower the vehicle comple-
tely.
WARNING
If the road wheels are hot, allow
them to cool sufficiently before tigh-
tening the wheel nuts. Otherwise, the
wheel nuts cannot be tightened to
specification.
NOTE:.
As soon as possible, tighten the
wheel nuts to the specified torque
with a torque wrench.
Wheel nut tightening torque:
Do-it-yourself
8-45

in a safe
place. To purchase a lock key, con-
tact a GT-R certified NISSAN dealer
with your original codeon the key
code card.
. When you ask for a service at a GT-R
certified NISSAN dealer, make sure
to keep the lock key in the vehicle.
Otherwise, tires cannot be removed
and any service requiring the re-
moval of the wheels cannot be
performed.
Do-it-yourself
8-47

In-cabin microfilter .................................................... 4-13
Increasing fuel economy ...................................... 5-42
Indicators and display ............................................. 5-36
Infants .................................................................................. 1-13
Injured persons ................................................................. 1-9
Inside mirror ................................................................... 3-27
Inspection and adjustments
after driving ............................................................... GTR-19
Inspection and adjustments
before driving .......................................................... GTR-14
Installing front license plate ............................ 10-16
Installing top tether strap .................... 1-26, 1-30
Instrument brightness control ......................... 2-12
Instrument panel ............................................................ 2-5
Intelligent Key .................................................................... 3-2
Intelligent Key battery discharge ................... 5-12
Intelligent Key battery
discharge indicator ................................................... 2-48
Intelligent Key battery replacement ............ 8-25
Intelligent Key functions ........................................... 3-9
Intelligent Key insertion indicator ................. 2-47
Intelligent Key removal indicator ................... 2-47
Intelligent Key system ................................................. 3-8
Interior light control switch ................................ 2-70
Interior lights .................................................................. 2-69
J
Jacking vehicle and removing wheels....... 8-41
Jump starting ..................................................... 6-5, 8-15
K
Key
Intelligent Key ............................................................ 3-2
Intelligent Key battery discharge ............ 5-12
Intelligent Key battery
discharge indicator ............................................ 2-48
Intelligent Key battery replacement ..... 8-25
Intelligent Key functions ................................... 3-9
Intelligent Key insertion indicator .......... 2-47
Intelligent Key removal indicator ............ 2-47
Intelligent Key system ......................................... 3-8
Keys ................................................................................... 3-2
Locking with mechanical key ....................... 3-6
No key warning ..................................................... 2-45
Remote keyless entry system ................... 3-12
L
M
Maintenance
Brake system (NCCB (NISSAN Carbon
Ceramic Brake)) ..................................................... 8-20
Explanation of maintenance items .......... 9-3