2022 MERCEDES-BENZ S-CLASS SALOON engine

#
Turn cap 1anti-clockwise and remo veit. #
Top up the engine oil. #
Replace cap 1and turn it clockwise until it
engages. #
Check the oil le vel again (/ page 365). Chec
Chec
king t
king t he coolant lev
he coolant lev el
el &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING Risk of scalding from hot cool-
ant
If yo u open the cap, you could be scalded. #
Let the mo tor cool down before opening
th e cap. #
When opening the cap, wear pr otective
glo ves and saf ety glasses. #
Open the cap slo wlytorelease pressure. #
Only ha vethe coolant checked or re/lled at a
qu ali/ed specialist workshop. T
T
opping up t
opping up t he windscr
he windscreen w
een washer syst
asher syst em
em &
W
WARNING
ARNING Risk of injury due tomoving
parts
Components in the engine compartment may
continue torun or start unexpectedly even
when the drive system is switched o..
Obser vethefo llowing if you must open the
bonnet: #
Switch o. theve hicle. #
Neverto uch the danger zones sur round-
ing moving components, e.g. thero tation
area of thefa n. #
Remo vejewe llery and watches. #
Keep items of clo thing and hair away
from moving pa rts. &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. Main
tenance and ca re
367
367

#
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING ‑ Risk of /re and injury due to
windscreen washer concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. It could ignite if it comes into contact
with hot engine component parts or the
ex haust system. #
Make sure that no windscreen washer
concent rate spills out next tothe /ller
opening. #
Remo vecap 1bytheta b. #
Top up thewa sher 0uid.
% Further information about the windscreen
wa sher 0uid (/ page 423) K K
eeping t
eeping t he air
he air-w
-wat
ater duct fr
er duct fr ee
ee #
Keep the area between the bonnet and the
windscreen free of deposits, e.g. ice, snow
and lea ves. Cleaning and care Cleaning and care
Inf
Inf
or
ormation on w
mation on w ashing t
ashing the v
he vehicle in a car w
ehicle in a car w ash
ash &
W
WARNING
ARNING Risk of an accident due to
re duced braking po wer aTer washing the
ve hicle
Braking e1ciency is reduced aTer washing the
ve hicle. #
ATer theve hicle has been washed, brake
carefully while paying attention tothe
tra1c conditions until braking po wer has
been fully restored. 368
368
Maintenance and ca
re

To
avo id damage toyour vehicle, obser vethefo l-
lowing when using a high-pressure cleaner:
R The key is at a minimum dis tance of 3 m away
from theve hicle. Otherwise the boot lid or a
door could open unintentionall y.
R Maintain a distance of at least 30 cm tothe
ve hicle.
R V
Vehicles wit
ehicles wit h decor
h decorativ
ative f
e foil:
oil: Parts of your
ve hicle are co vered with a decorative foil.
Maintain a distance of at least 70 cm between
th efo il-co vered parts of theve hicle and the
nozzle of the high-pressure cleaner. Mo vethe
high-pressure cleaner nozzle around whilst
cleaning. The waterte mp erature of the high-
pressure cleaner must not exceed 60°C.
R Obser vethe information on the cor rect dis-
ta nce in the equipment manufacturer's oper-
ating inst ructions.
R Do not direct the nozzle of the high-pressure
cleaner directly at sensitive parts, such as
tyres, gaps, electrical components, batteries,
light sources and ventilation slits. W W
ashing t
ashing t he v
he vehicle b
ehicle b y hand
y hand *
N
NOOTE
TE Engine damage due towa ter ing ress #
Take care not topoint thewa ter jet
directly towa rdsth e air inlet grille below
th e bonnet. obser
vethe legal requ irements, e.g. in a number
of countries, washing byhand is only permitted in
special lydesignated wash ba ys. #
Use a mild cleaning agent, e.g. car shampoo. #
Washtheve hicle with luk ewarm water using a
soT car sponge. When doing so, do not
ex pose theve hicle todirect sunlight. #
Carefully hose theve hicle o. with water and
dry using a chamois.
% Obser vethe no tes on the care of car parts
(/ page 372). N No
ot
tes on paintw
es on paintw or
ork/matt
k/matt /nish
/nishpaintw
paintw or
ork care
k care To
avo id damaging the paintwork and inter fering
with the driving assistance systems, please
obser vethefo llowing no tes: P
P
aint
aint
R Insect remains: soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: soak with water and rinse o.
aTer wards.
R Tree resin, oils, fuels and greases: remo veby
ru bbing gently with a clo thsoaked in petro-
leum ether or lighter 0uid.
R Coolant and brake 0uid: remo vewith a damp
clo thand clean water.
R Tar stains: use tarre mo ver.
R Wax: use silicone remo ver.
R Do not attach sti ckers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a quali/ed specialist workshop.
R Remo vedirt immediatel y,where possible.
Matt
Matt /nish
/nish
R Only use care products appr ovedfor
Mercedes-Benz.
R Do not attach stic kers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a qu ali/ed specialist workshop. 370
370
Main
tenance and ca re

R
Do not polish theve hicle and light-alloy
wheels.
R Only use car washes that cor respond tothe
latest engineering standards.
R Do not use car wash prog rammes with a /nal
hot wax treatment.
R Do not use paint cleaners, bu1ng or polishing
products, gloss preser vers, e.g. wax.
In theev ent of paintwork damage:
R Always ha vepaintwork repairs car ried out at a
qu ali/ed specialist workshop.
R Make sure thera dar sensors function
(/ page 228). N No
ot
tes on cleaning decor
es on cleaning decor ativ
ative f
e foils
oils Obser
vethe no tes on matt /nish care in thech ap-
te r "No tes on paintwork/matt /nish paintwork
care" (/ page 370). They also apply tomatt dec-
orative foils.
Obser vethe no tes on cleaning decorative foils to
av oid vehicle damage. Cleaning
Cleaning
R For cleaning, use plenty of water and a mild
cleaning agent without additives or abrasive
substances, e.g. a car shampoo appr ovedfor
Mercedes-Benz.
R Remo vedirt immediatel y,where possible,
whilst avoiding rubbing too hard. There is oth-
erwise a risk of damaging the decorative foil
ir re parabl y.
R Ifth ere is dirt on the /nish or if the decorative
fo il is dull: Use thePa int Cleaner recommen-
ded and appr ovedfo r Mercedes-Benz.
R Insect remains: Soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: Soak with water and rinse o.
aTer wards.
R Topreve ntwa ter stains, dry a foil-wrapped
ve hicle with a soT, absorbent clo thaTer every
car wash.
Av Av oiding damag
oiding damag e t
e to t
o t he decor
he decor ativ
ative f
e foil
oil
R The service life and colouring of decorative
foils are impaired by:
- Sunlight -
Tempe rature, e.g. hot air blo wer
- Weather conditions
- Stone chippings and dirt
- Chemical cleaning agents
- Oily products
R Do not use polish on matt decorative foil. Po l-
ishing will ha vethe e.ect of shining thefo il-
wrapped sur face.
R Do not treat matt or st ructured decorative
fo ils with wax.Pe rm anent stains may occur.
Scratches, cor rosive deposits, areas a.ected by
cor rosion and damage caused byincor rect care
cannot alw ays be comple tely re paired. In such
cases, visit a quali/ed specialist workshop.
Yo u can obtain more information on care and
cleaning products from the manufacturer.
In the case of foil-wrapped sur faces, optical di.er-
ences may occur between the sur faces that we re
not pro tected bya decorative foil aTer removing a
decorative foil. Maintenance and care
371 371

Ke
ep children away. Obser
vethis Owner's Manual.
Obser vethefo llowing if you do not intend touse
th eve hicle over an extended period of time:
R Activate standby mode.
R Alternativel y:connect the battery toa battery
ch arge r appr ovedby Mercedes-Benz or con-
sult a quali/ed specialist workshop todiscon-
nect the batter y. N
N
o
ot
tes on st
es on st ar
arting assist
ting assist ance and c
ance and c har
harging t
ging t he 12
he 12
V batt
V batt ery
ery V
V
ehicles wit
ehicles wit h a lit
h a lithium-ion batt
hium-ion batt ery
ery
When charging the battery and during starting
assistance, alw ays use the jump-start connection
point in the engine compartment. *
N
NOOTE
TE Damage tothe battery from over-
vo ltage When
charging using a battery charge r without
a re striction of the maximum charging voltage,
th e battery or the on-board electronics can be
damaged. #
Only use battery charge rs with a maxi-
mum charging voltage of 14.8 V. All
ot
All other v
her v ehicles
ehicles
When charging the battery and during starting
assistance, alw ays use the jump-start connection
point in the engine compartment.
* NO
NOTE
TEDamage tothe battery from over-
vo ltage When
charging using a battery charge r without
a re striction of the maximum charging voltage,
th e battery or the on-board electronics can be
damaged. #
Only use battery charge rs with a maxi-
mum charging voltage of 14.8 V. &
W
WARNI NG
ARNI NGRisk of explosion due tohydro-
ge nga s igniting
If, when charging a batter y,there is a short
circuit or spar ksstart toform ,th ere is a dan-
ge r of hydrogen gas igniting. #
Take care that the positive clamp con-
nected toa battery does not come into
contact with vehicle parts. #
Never place me tal objects or tools on a
batter y. #
When connecting and disconnecting the
batter y,alw ays obser vethe sequence of
battery clamps described. #
Take care toonly connect battery term i-
nals of identical polarity when receiving
starting assistance. #
Obser vethe sequence described for
connecting and disconnecting the jump
leads when receiving starting assistance. #
Do not connect or disconnect the bat-
te ry term inals while the engine is run-
ning. 384
384
Breakdown assistance

&
W
WARNI NG
ARNI NGRisk of explosion due toexplo-
sive mixture of gases
An explosive mixture of gases can escape
from the battery during charging and starting
assis tance. #
Fire , naked 0ames, smoking and creating
spar ksmust be avoided. #
Make sure there is adequate ventilation. #
Do not stand overth e batter y. &
W
WARNI NG
ARNI NGRisk of explosion from a frozen
battery
A dischar ged battery may freeze at temp era-
tures slightly abo veor below freezing point.
During starting assistance or battery charging,
battery gas can be released. #
Always allow a battery tothaw before
ch arging it or per form ing starting assis-
ta nce. If
th e indicator/warning lamps in the inst rument
cluster do not light up at low temp eratures, it is
ve ry likely that the dischar ged battery has frozen. In
this case you may neither jump-start theve hi-
cle nor charge the batter y.
The service life of a bat tery that has been thawed
may be dramatically shor tened. The starting char-
acteristics may be impaired, especially at low
te mp eratures.
It is recommended that you ha veath awe d battery
ch ecked at a quali/ed specialist workshop.
All v All v ehicles
ehicles
* NO
NOTE
TEDamage caused bynume rous or
ex tended attem ptsto start the engine Numerous or
extended attem ptsto start the
engine may damage the catalytic con verter
due tonon-combusted fuel. #
Avoid numerous and extended attem pts
to start the engine. Obser
vethefo llowing points during starting assis-
ta nce and when charging the batter y:
R Only use undamaged jump lead/charging
cables with a su1cient cross-section and
insulated term inal clamps. R
Non-insulated parts of thete rm inal clamps
must not come into contact with other me tal
parts while the jump lead/charging cable is
connected tothe battery/jump-start connec-
tion point.
R The jump lead/charging cable must not come
into contact with any parts which may mo ve
when the engine is running.
R Always make sure that nei ther you nor the bat-
te ry is electros tatically charge d.
R Keep awa y from /re and naked 0ames.
R Do not lean overth e batter y.
Obser vethe additional following points when
ch arging the batter y:
R Only use battery charge rs tested and
appro vedfo r Mercedes-Benz.
R Read the battery charge r's operating inst ruc-
tions before charging the batter y. Breakdow
n assistance
385 385

Obser
vethe additional following points during
starting assistance:
R Starting assis tance may only be provided
using vehicles, batteries or other jump start
devices with a nominal voltage of 12 V.
R The vehicles must not touch.
R V
Vehicles wit
ehicles wit h a pe
h a petr
trol engine:
ol engine: jump-start the
ve hicle only when the engine and exhaust sys-
te m are cold. S
S
t
tar
ar ting assist
ting assist ance and c
ance and c har
harging t
ging t he 12 V batt
he 12 V batt ery
ery Pr
Pr
epar
epar ing f
ing for st
or st ar
arting assist
ting assist ance/t
ance/the che char
harging
ging
pr
pr ocess
ocess #
Secure theve hicle byapplying the electric
parking brake. #
ShiT the transmission toposition j. #
Switch o. theve hicle and all elect rical con-
sumers. #
Open the bonnet. #
Open co ver1. #
Slide pr otective co ver2 of POSITIVE contact
3 onthe jump-start connection point in the
direction of the ar row. S
S
t
tar
ar ting assist
ting assist ance
ance #
Connect the POSITIVE contacts of theve hi-
cles with the jump lead. Start with your own
ve hicle /rst. #
Start the engine of the donor vehicle and run
it at idling speed. #
Connect the negative term inal of the donor
battery toear thpoint of your vehicle 4using 386
386
Breakdown assis
tance

th
e jump lead. Start with the donor vehicle
/rst. #
Start the engine of your ow nve hicle. #
Let the engines runfo r se veral minutes. #
Before disconnecting the jump leads, switch
on an electrical consumer in your ow nve hicle,
e.g. there ar wind owheater or the lighting.
When starting assistance has /nished: #
Firs t, re mo vethe jump lead from the ear th
point of your ow nve hicle and the negative ter-
minal of the donor batter y,then remo vethe
jump lead from the POSITIVE contacts of bo th
ve hicles. Alw ays start with your ow nve hicle
/rst. #
Close pr otective co ver2 of POSITIVE con-
ta ct 3 and close co ver1.
Fu rther information can be obtained at a quali/ed
specialist workshop. Char
Char
ging t
ging t he 12 V batt
he 12 V batt ery
ery #
Connect the POSITIVE contacts of theve hicle
and thech arge r with thech arging cable. Start
with theve hicle /rst. #
Connect the NEG ATIVE contact of thech arger
and ear thpoint 4ontheve hicle with the
ch arging cable. Start with thech arge r /rst. #
Start thech arging process.
When thech arging process is comple te: #
Remo vethech arging cable from ear thpoint
4 ontheve hicle and the NEG ATIVE contact
of thech arge r /rst and then from the POSI-
TIVE contacts on theve hicle and charge r.
Alw ays start with theve hicle /r st. #
Close pr otective co ver2 of POSITIVE con-
ta ct 3 and close co ver1. R
R
eplacing t
eplacing t he 12 V batt
he 12 V batt ery
ery #
Obser vethe no tes on the 12 V battery
(/ page 382). Mercedes-Benz
recommends that you ha vethe
12 V battery replaced at a quali/ed specialist
wo rkshop, e.g. at a Mercedes-Benz Se rvice
Centre.
Obser vethefo llowing no tes if youwa nttoreplace
th e battery yourself:
R Alwaysre place a faulty battery with a battery
which meets the speci/c vehicle requ ire-
ments.
The vehicle is equipped with an AGMtech nol-
ogy bat tery (Absorbent Glass Mat) or a lith-
ium-ion batter y.Fu llve hicle functionality is
only guaranteed with an AGM bat tery or lith-
ium-ion batter y.Fo r saf etyre asons, Mercedes-
Benz recommends that you only use batteries
which ha vebeen tested and appro vedfo ryo ur
ve hicle byMercedes-Benz.
R Carryove r de tach able parts, such as vent
hoses, elbow /ttings or term inal co vers from
th e battery being replaced.
R Make sure that theve nt hose is alw ays con-
nected tothe original opening on the side of
th e batter y.
Fi t any existing or supplied cell caps. Breakdown assistance
387 387