2022 MERCEDES-BENZ EQE SALOON auxiliary battery

%
When using a CCS (Combined Charging Sys-
te m) charging cable tocharge with direct cur-
re nt at a combo vehicle soc ket, bo thvehicle
soc ket connections 1and 2are used for
ch arging.
Charging options forth e high-voltage battery
(mode 2, 3 or 4):
R Charging through recuperation while theve hi-
cle is in motion
R Charging with alternating cur rent when sta-
tiona ry:
- at a mains soc ket (mode 2)
- at a wallbox or charging station (mode 3)
R Charging with direct cur rent when stationar y:
- at a rapid charging station (mode 4)
Depending on the count ry-speci/c vehicle equip-
ment and your vehicle's charging cable, single
phase ACcharging is also possible.
Obser vethe di.erent grid requ irements of your
cur rent location when charging. Only use charging
cables which conform tothegr id requ irements.
Consult a quali/ed elect rician or your local grid
operator if you ha veany questions. It is
recommended that youch arge the high-volt-
age battery at a wallbox or charging station due to
th e impr ovedch arging per form ance and better
ch arging e1ciency o.ered.
S
S t
to
o wing t
wing t he c
he char
harging cable
ging cable
Alw ays st owtheve hicle charging cable in the
ch arging cable bag pr ovided and attach its spring
hook tothe tie-down eye in the boot or the load
compartment.
Otherwise, thech arging cable is not su1ciently
secured.
Syst
Syst em limits em limits
The po wer output of the high-voltage battery may
be impaired bythefo llowing:
R High or low outside temp eratures
R Electrical auxiliary consumers in theve hicle
being switched on, e.g. operating the air con-
ditioning system
R Extended periods without charging
The charging time of the high-voltage battery may
be increased bythefo llowing:
R High or low outside temp eratures R
Extended periods without charging
R The maximum available charge cur rent of the
ch arging facility
R The settings of thech arging process in the
multimedia system (/ page 211) N
No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at t
y at t he
he
mains soc ke
mains soc ket (mode 2)
t (mode 2) &
D
DAN
AN GER
GER Risk of fatal injury from incor-
re ctly ins talled component parts
Connecting thech arging cable toa mains
soc ket using incor rectly ins talled component
parts could cause a /re or an electric shoc k,
fo rex ample. #
Only connect thech arging cable to a
mains soc ketth at:
R Has been proper lyinstalled and
R Has been inspected byaqu ali/ed elect ri-
cian Driving and parking
195
195

#
Never use damaged charging cables. #
Do not extend thech arging cable. #
Do not use adap ters. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth ewa llbox. If
ch arging at a wallbox without pre-ins talled
cable, use the optionally available charging cable
fo rwa llbox and charging station (mode 3). The
ch arging cable is st owed in a bag in the boot/
luggage compartment.
Only use charging cables that ha vebeen tested
and appro vedby the manufacturer forch arging
th e high-voltage battery in an electric vehicle. &
D DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable: R
Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card or
via Plug & Char ge. Obser vethe on-site operator's
inst ructions forth ech arging station and the no tes
on Mercedes me Char ge(see theve hicle's Digital
Owner's Manual). The amount of ene
rgy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when
ch arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. N No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at a
y at a
r
r apid c
apid c har
harging st
ging st ation (mode 4)
ation (mode 4) &
D
DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable: Driving and parking
197
197

R
Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. &
D
DAN
AN GER
GER Risk of fatal injuries when car ry-
ing out maintenance workduring the
ch arging process
During thech arging process, the high-voltage
on-board electrical system is under high volt-
age. #
Do not per form any main tenance work
during thech arging process. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card or
via Plug & Char ge. Obser vethe on-site operator's
inst ructions forth ech arging station and the no tes
on Mercedes me Char ge(see theve hicle's Digital
Owner's Manual).
The charging cable forth eve hicle must not be
lon gerth an 30 m due tothe legal requ irements in
some countries. This is toprev ent the inter fer-
ence of signals being received byradio communi-
cation devices in theve hicle or in close pr oximity
to thech arging station. Be awarethat parts of the
ch arging cable may be routed under ground. If in
doubt, ask thech arging station operator if this is
th e case before charging the high-voltage batter y.
The amount of energy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when ch
arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. Se Se
tting t
tting t he maximum per
he maximum per missible c
missible char
harging cur-
ging cur-
r
r ent f
ent f or c
or char
harging at a mains soc ket
ging at a mains soc ket *
N
NO
OTE
TE Overloading the mains soc ket due
to excessive charging cur rent If
th ech arging cur rent is too high, the fuse
could be tripped or theex tern al mains supply
could overheat. #
Ensure that theex tern al mains supply
has been designed tohandle thech arg-
ing cur rent pr ovided. #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable.
Mercedes-Benz thoroughly tests these
original charging cables forth eir suitabil-
ity for high-voltage charging of your vehi-
cle. Pur chase these parts at a Mercedes- 198
198
Driving and parking

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences andM
MSolutions
Solutions
N is selected Please select
desired transmission posi-
tion *T
he accelerator pedal was depressed while theve hicle wasro lling or moving in neutral i. #
Toaccelerate theve hicle, select transmission position hork.
Reversing not poss. Con-
sult workshop *T
he transmission is malfunctioning. It is not possible toselect transmission position k. #
Consult a quali/ed specialist workshop.
Transmission Malfunction
Stop *T
he transmission is malfunctioning. The transmission shiTs toneutral iautomaticall y. #
Stop theve hicle immediately in accordance with the tra1c conditions. #
Depress the brake pedal. #
Engage park position j. #
Consult a quali/ed specialist workshop.
Consult workshop without
changing the transmission
position *T
he transmission is malfunctioning. It is no lon ger possible tochange the transmission position. #
If transmission position his selected, consult a quali/ed specialist workshop and do not change the transmission
position. #
For all other transmission positions, park theve hicle safel y. #
Consult a quali/ed specialist workshop.
Auxiliary battery malfunc-
tion (white display message) *T
here is a malfunction in the auxiliary batter y. #
Consult a quali/ed specialist workshop. #
Until then, alw ays select park position jmanually before you switch o. theve hicle. 456 456
Displ
aymessages and warning/indicator lamps