*
N
N O
OTE
TE Damage caused bythe wrong fuel Ve
hicles with a diesel engine:
Even small amounts of the wrong fuel could
re sult in damage tothe fuel system, the
engine and the emission control system. #
Only refuel using sulphur-free diesel fuel
th at conforms toEuropean standard
EN 590, or an equivalent speci/cation.
In count ries without sulphur-free diesel
fuel, refuel using only lo w-sulphur diesel
fuel with a sulphur content less than
50 ppm. #
V
Vehicles wit
ehicles wit hout diesel par
hout diesel par ticulat
ticulate
e/lt
/lt er:
er:
Only refuel using diesel fuel wi tha sul-
phur content less than 500 ppm.
Ne verre fuel wi thone of thefo llowing fuels:
R Petrol
R Marine diesel
R Heating oil
R Pure bio-diesel or vege table oil
R Para1n or kerosene If
yo u ha veacciden tally refuelled wi th the
wrong fuel: #
Do not switch on theve hicle. #
Consult a quali/ed specialist workshop. *
N
NOOTE
TE Do not use diesel torefuel vehicles
with a petrol engine If
yo u ha veacciden tally refuelled wi th the
wrong fuel:
R Do not switch on theve hicle. Otherwise
fuel can enter the engine.
Even small amounts of the wrong fuel
could result in damage tothe fuel system
and the engine. The repair costs are high. #
Consult a quali/ed specialist workshop. #
Have the fuel tank and fuel lines drained
comple tely. *
N NO
OTE
TE Do not use petrol torefuel vehicles
with a diesel engine If
yo u ha veacciden tally refuelled wi th the
wrong fuel:
R Do not switch on theve hicle. Otherwise,
fuel can enter the fuel system.
Even small amounts of the wrong fuel
could result in damage tothe fuel system
and the engine. The repair costs are high. #
Consult a quali/ed specialist workshop. #
Have the fuel tank and fuel lines drained
comple tely. *
N NO
OTE
TE Damage tothe fuel system caused
by ove r/lled fuel tanks #
Only /ll the fuel tank until the pump noz-
zle switches o.. Driving and parking
195
195
Inf
Inf
or
ormation on v
mation on v ehicle sensor
ehicle sensor s and camer
s and cameras
as Some driving and driving saf
ety sy stems use cam-
eras as well as radar or ultrasonic sensors to
monitor the area in front of, behind or next tothe
ve hicle. 1
Multifunction camera
2 Cameras in the outside mir rors
3 Front radar 4
Front camera
5 Corner radars
6 Ultrasonic sensors
7 Reversing camera &
W
WARNING
ARNING Risk of accident due torestric-
te d de tection per form ance of vehicle sen-
sors and cameras
If th e area around vehicle senso rsor cameras
is co vered, damaged or dirty, cer tain driving
and saf ety sy stems cannot function co rrectl y.
There is a risk of an accident. #
Keep the area around vehicle senso rsor
cameras clear of any obst ructions and
clean. #
Have damage tothe bumper, radiator
gr ille or stone chipping in the area of the
front and rear wind owsre paired at a
qu ali/ed specialist workshop. Pa
rticular ly,ke ep the areas around the sensors
and cameras free of dirt, ice or slush
(/ page 351). The sensors and cameras must not be co
vered and the de tection ranges around
th em must be kept free. Do not at tach additional
licence plate brac kets, advertisements, stic kers,
fo ils or foils toprotect against stone chippings in
th e de tection range of the sensors and cameras.
Make sure that there are no overhanging loads
pr otru ding into the de tection range.
If th ere is damage toa bumper or thera diator
gr ille, or aTer an impact, ha vethe function of the
senso rschecked at a quali/ed specialist work-
shop. Ha vedamage or stone chipping in the area
of the cameras on the front and rear wind ows
re paired at a quali/ed specialist workshop.
% The reve rsing camera can extend and retract
automatically forth e purpose of calibration,
ev en though there is no camera image in the
displa y. Ov Ov
er
ervie
vie w of dr
w of dr iving syst
iving syst ems and dr
ems and dr iving safe
iving safety
ty
syst
syst ems
ems R
ABS (AA nti-lo ck BBra king S System) (/ page 219)
R BAS (BBra ke AAssist S System) (/ page 220) 218
218
Driving and parking
R
Frequent operation in mountainous terrain or
on poor road sur faces
R When the engine is oTen leT idling for long
periods
R Operation in particular lydusty conditions
and/or if air-recirculation mode is frequently
used
In these or similar operating conditions, ha vethe
interior air /lter, air /lter, engine oil and oil /lter,
fo rex ample, changed more frequentl y.Check the
tyres more frequently if theve hicle is operated
under increased st ress. Further information can
be obtained at a quali/ed specialist workshop. Batt Batt
er
ery disconnection per
y disconnection per iods
iodsThe AS
SYST PLUS service inter val display can cal-
culate the service due date only when the battery
is connected. #
Display and no tedown the service due date
on the inst rument display before disconnect-
ing the battery (/ page 340). Engine com
Engine com
par
partment
tment A
A
ctiv
ctiv e bonne
e bonne t (pedes
t (pedestr trian pr ot
ian pr otection)
ection) Oper
Oper
ation of t
ation of t he activ
he active bonne
e bonne t (pedes
t (pedestr trian pr ot
ian pr otec-
ec-
tion)
tion)
In cer tain accident situations, the actuation of the
active bonnet reduces therisk of injury topedes-
trians. The rear area of the bonnet is raised by
appr oximately 80 mm.
ATer being triggered, the active bonnet remains in
th era ised position. Limited visibility due tothe
ra ised bonnet cannot be ruled out.
ATer the active bonnet has been actuated, pedes-
trian pr otection may be limited.
Ha ve the full functionality of the active bonnet
re stored immediatel y in aquali/ed specialist
wo rkshop.
If necessar y,adjust your seat position and drive
carefully toaqu ali/ed specialist workshop. If a
safe continued jou rney is not possible, contact a
qu ali/ed specialist workshop. Opening and closing t Opening and closing t
he bonnet
he bonn et &
D
DAN
AN GER
GER Risk of fatal injuries when car ry-
ing out maintenance workduring the
ch arging process
During thech arging process, the high-voltage
on-board electrical system is under high volt-
age. #
Do not per form any main tenance work
during thech arging process. &
W
WARNING
ARNING Risk of accident due todriving
with the bonnet unloc ked
The bonnet may open and blo ckyour vie w. #
Neverre lease the bonnet when driving. #
Before every trip, ensure that the engine
bonnet is loc ked. &
W
WARNING
ARNING Risk of accident and inju ry
when opening and closing the bonnet
The bonnet may suddenly drop into the end
position. Maintenance and care
341
341
There is a
risk of injury for an yone in the
engine bonnet's range of mo vement. #
Do not open or close the bonnet if there
is a person in the bonnet's range of
mo vement. &
W
WARNING
ARNING Risk of burns when opening the
bonnet
If yo u open the bonnet in theev ent of an over-
heated engine or /re in the engine compart-
ment, thefo llowing situations may occur:
R You may come into contact with hot gases.
R You may come into contact with other
escaping hot operating 0uids. #
Before opening the bonnet, allow the
engine tocool down. #
Intheev ent of a /re in the engine com-
partment, keep the bonnet closed and
call the /re service. &
W
WARNING
ARNING Risk of injury due tomoving
parts
Components in the engine compartment may
continue torun or start unexpectedly even
when the drive system is switched o..
Obser vethefo llowing if you must open the
bonnet: #
Switch o. theve hicle. #
Neverto uch the danger zones sur round-
ing moving components, e.g. thero tation
area of thefa n. #
Remo vejewe llery and watches. #
Keep items of clo thing and hair away
from moving pa rts. &
W
WARNING
ARNING Risk of injury from touching
components under voltage
The ignition system and the fuel injection sys-
te m operate at high voltage. You could receive
an elect ric shoc k. #
Neverto uch ignition system or fuel injec-
tion system components when theve hi-
cle is switched on. The live components include
thefo llowing, for
ex ample:
R Ignition coils
R Fuel injectors
R Electric lines tothe ignition coils and the fuel
injectors &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. 342
342
Maintenance and care
#
Ifth e bonnet can still be liTed slightl y,open
th e bonnet again and close it with a little more
fo rc e until it engages cor rectl y. Engine oil
Engine oil
Chec
Chec
king t
king t he engine oil lev
he engine oil lev el using t
el using the oil dips
he oil dips tick
tick &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. R
R
eq
eq uir
uir ements:
ements:
R The engine has an oil dipstic k.If not, the
engine oil le vel can be checked only with the
on-board computer (/ page 344) .
Depending on the engine, the oil dipstick may be
installed in the engine compartment in di.erent
locations. The
waiting time before checking the oil le vel
when the engine is at normal operating temp era-
ture is /ve minutes. #
Park theve hicle on a le vel sur face. #
Pull oil dipstick 1out and wipe o.. #
Slowly slide oil dipstick 1into the guide tube
to the stop, and pull it out again aTer appr ox-
imately thre e seconds.
R Oil le vel is cor rect: oil le vel is between 2
and 3.
R Oil le velto o lo w:oil le vel is at 3or belo w.
R Oil le velto o high: oil le vel is abo ve2 . #
Ifth e oil le vel is too lo w,top up with 1 litre of
engine oil. #
Ifth e oil le vel is too high, drain o. excess
engine oil. Consult a quali/ed specialist work-
shop.
Chec
Chec king t
king t he engine oil lev
he engine oil lev el using t
el using the on-board
he on-board
com
com put
puter
er
R
R eq
eq uir
uir ements:
ements:
R The engine has been warmed up.
R The vehicle is par ked on a le vel sur face.
R The engine is running at idle speed.
R The bonnet is closed.
The engine oil le vel is de term ined during driving.
De term ining the engine oil le vel can take up to 344
344
Maintenance and care
30 minutes with a normal driving style and
even
longer with an active driving style.
On-board computer:
4 Service 5
Engine oil level
One of thefo llowing message s will appear onthe
inst rument displa y:
R Engine oil level Measuring now: measu rement
of the oil le vel is not yet possible. #
Repeat there qu est aTer a maximum of
30 minutes' driving.
R Engine oil level OK andthe bar display for
indicating the oil le vel on the inst rument dis-
play is green and is between "min" and "max":
th e oil le vel is cor rect.
R Engine oil level Add 1,0 l andthe bar display
fo r indicating the oil le vel on the inst rument
display is orange and is below "min": #
Add 1 l of engine oil.
R Reduce engine oil level andthe bar display for
indicating the oil le vel on the inst rument dis-
play is orange and is abo ve"max": #
Drain o. any excess engine oil that has been
added. Todo so, consult a quali/ed specialist
wo rkshop.
R For engine oil level turn on ignition #
Switch on theve hicle tocheck the engine oil
le ve l.
R Engine oil level System inoperative: The oil
leve l sensor is defective or not connected. #
Consult a quali/ed specialist workshop.
R Engine oil level System currently unavail. #
Close the bonnet.
T T op up engine oil
op up engine oil &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING Risk of /re and injury from
engine oil
If engine oil comes into contact with hot com-
ponent parts in the engine compartment, it
may ignite. #
Make sure that no engine oil is spilled
next tothe /ller opening. #
Allow the engine tocool o. and thor-
oughly clean the engine oil from compo-
nent parts before starting theve hicle. *
N
NOOTE
TE Engine damage caused byan inco r-
re ct oil /lter, incor rect oil or additi ves #
Do not use engine oils or oil /lters which
do not cor respond tothe speci/cations
ex plicitly prescribed forth e service inter-
va ls. #
Follow the inst ructions on the service
inter val display forch anging the engine
oil and obser vethe prescribed change
inter vals. #
Do not use additives. Maintenance and care
345 345
*
N
NO
OTE
TE Damage caused bytopping up too
much engine oil To
o much engine oil can damage the engine or
th e catalytic con verter. #
Have excess engine oil remo ved at a
qu ali/ed specialist workshop. %
Depending on driving st yle, theve hicle con-
sumes up to0.8 litre of oil per 1000 km. The
oil consum ption may be higher than this when
th eve hicle is new or if you frequently drive at
high engine speeds. #
Turn cap 1anti-clockwise and remo veit. #
Top up the engine oil. #
Replace cap 1and turn it clockwise until it
engages. #
Check the oil le vel again (/ page 344). Chec
Chec
king t
king t he coolant lev
he coolant lev el
el &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING Risk of scalding from hot cool-
ant
If yo u open the cap, you could be scalded. #
Let the mo tor cool down before opening
th e cap. #
When opening the cap, wear pr otective
glo ves and saf ety glasses. #
Open the cap slo wlytorelease pressure. 346
346
Maintenance and care
#
Ensure there is su1cient ground clear-
ance between the underbody and the
guide rails of the car wash. #
Ensure that the clearance width of the
car wash, in particular the width of the
guide rails, is su1cient. To
avo id damage toyour vehicle when using a car
wa sh, ensu rethefo llowing beforehand:
R Active Distance Assist DISTRONIC is deactiva-
te d.
R The HOLD function is switched o..
R The 360° Camera or there ve rsing camera is
switched o..
R The side windo wsand sliding sunroof are com-
ple tely closed.
R The blo werfo rth eve ntilation and heating is
switched o..
R The windsc reen wiper switch is in position g.
R The key is at a minimum dis tance of 3 m away
from theve hicle. Otherwise the boot lid could
open unintentionall y.
R For car washes with a con veyor system: -
Neutral iis engaged.
- Ifyo uwo uld like tolea vetheve hicle while
it is being washed, make sure theke y is
located in theve hicle. The park position
j isotherwise automatically engaged.
% If, aTer the car wash, youre mo vethewax
from the windscreen and wiper rubbers, this
will pr event smearing and reduce wiper noise. Inf
Inf
or
ormation on using a high-pr
mation on using a high-pr essur
essure cleaner
e cleaner &
W
WARNING
ARNING Risk of an accident when using
high-pressure cleaners with round-spr ay
nozzles
The water jet can cause extern ally invisible
damage.
Components damaged in this wa y may un ex-
pectedly fail. #
Do not use a high-pressure cleaner with
round-spr aynozzles. #
Have damaged tyres or chassis parts
re placed immediatel y. To
avo id damage toyour vehicle, obser vethefo l-
lowing when using a high-pressure cleaner:
R The key is at a minimum dis tance of 3 m away
from theve hicle. Otherwise the boot lid could
open unintentionall y.
R Maintain a distance of at least 30 cm tothe
ve hicle.
R V Vehicles wit
ehicles with decor h decorativ
ative f
e foil:
oil: Parts of your
ve hicle are co vered with a decorative foil.
Maintain a distance of at least 70 cm between
th efo il-co vered parts of theve hicle and the
nozzle of the high-pressure cleaner. Mo vethe
high-pressure cleaner nozzle around whilst
cleaning. The waterte mp erature of the high-
pressure cleaner must not exceed 60°C.
R Obser vethe information on the cor rect dis-
ta nce in the equipment manufacturer's opera-
to r manual.
R Do not direct the nozzle of the high-pressure
cleaner directly at sensitive parts such as
tyres, gaps, electrical component parts, bat-
te ries, illuminants and louvres. Maintenance and care
349 349