2022 MAZDA MODEL MX-30 EV coolant temperature

Coolant
▼Inspecting Coolant Level
WARNING
Do not use a match or live
flame in
the motor compartment. DO NOT
ADD COOLANT WHEN THE EV
SYSTEM IS HOT :
A hot EV system is dangerous. If the EV
system has been running , parts of the
motor compartment can become very
hot. You could be burned. Carefully
inspect the EV system coolant in the
coolant reservoir, but do not open it.
Pull over to a safe location, then
switch the power switch o ff and make
sure the fan is not running before
attempting to work near the cooling
fan:
Working near the cooling fan when it is
running is dangerous. The fan could
continue running inde finitely even if
the EV system has stopped and the
motor compartment temperature is
high. You could be hit by the fan and
seriously injured.
Do not remove either
cooling system cap when the EV
system and radiator are hot:
When the EV system and radiator are
hot, scalding coolant and steam may
shoot out under pressure and cause
serious injury.
NOTE
Changing the coolant should be done
by an Authorized Mazda Dealer.
Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year ―at the beginning of
the winter season ―and before
traveling where temperatures may drop
below freezing.

Inspect the condition and connections
of the cooling system.
Replace any that are swollen or
deteriorated.

The coolant should be between the
FULL and LOW marks on the coolant
reservoir when the EV system is cool.

If it is at or near LOW, add enough
coolant to the coolant reservoir to
provide freezing and corrosion
protection and to bring the level to
FULL.
Securely tighten the coolant reservoir
tank cap after adding coolant.
CAUTION
 Radiator coolant will damage paint.
Rinse it
off quickly if spilled.
Maintenance and Care
Owner Maintenance
6-11
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Do not rub the camera cover or lens
forcefully, or clean them with an
abrasive or hard brush.
NOTE
If there are water droplets, snow, or
mud on the camera lens, wipe it o ff
using a soft cloth. If the camera lens is
especially dirty, wash it o ff with mild
detergent.
▼ Aluminum Wheel Maintenance
A protective coating is provided over
the aluminum wheels. Special care is
needed to protect this coating.
CAUTION
Do not use any detergent other than
mild detergent. Before using any
detergent, verify the ingredients.
Otherwise, the product could discolor
or stain the aluminum wheels.
NOTE
Do not use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
Always use a sponge or soft cloth to
clean the wheels.
Rinse the wheels thoroughly with
lukewarm or cold water. Also, be
sure to clean the wheels after driving
on dusty or salted roads to help
prevent corrosion.
Avoid washing your vehicle in an
automatic car wash that uses
high-speed or hard brushes.
▼Plastic Part Maintenance
When cleaning the plastic lenses of
the lights, do not use gasoline,
kerosene,
rectified spirit, paint,
thinner, highly acidic detergents, or
strongly alkaline detergents.
Otherwise, these chemical agents
can discolor or damage the surfaces
resulting in a signi ficant loss in
functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, flush with water
immediately.
If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fluids such as
coolant, or lead-acid battery fluid, it
could cause discoloration, staining ,
or paint peeling. Wipe o ff any such
chemical agents or fluids using a soft
cloth immediately.
High water temperature and high
water pressure car washers are
available depending on the type of
high pressure car washer device. If
the car washer nozzle is put too
close to the vehicle or aimed at one
area for an extended period of time,
it could deform plastic parts or
damage the paint.
Do not use wax containing
compounds (polish). Otherwise, it
could result in paint damage.
In addition, do not use an electrical
or air tool to apply wax. Otherwise,
the frictional heat generated could
result in deformation of plastic parts
or paint damage.
Maintenance and Care
Appearance Care
6-39
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Specifications
▼ Charge System
Item
Servicing data
Input power 110 - 240 V AC (single phase)
Rated frequency 60 Hz
Maximum rated electrical current 32 A (normal charge)
Maximum power consumption 7.68 kVA (normal charge)
Maximum charging current 100 A (quick charge)
Electrical leakage detection current
for control box including genuine
charge cable 5 mA
EV charge mode/Connection type Normal charge: AC Level 1, AC level 2
Quick charge: CCS1 (Combo1)
Installation requirements
(information on protection against
short-circuit current and equipment
protection) Applicable laws and regulations, and standards must be followed
for protection measures against over-current and over-voltage.
Always make sure to install a ppropriate over-current protection
devices to the wiring of houses and buildings.
IP level IP44: When charge connector is connected to charge inlet
IP67: Charge cable
Operating temperature Onboard charger: -30 °C (-22 °F)
― 65 °C (149 °F) (coolant
temperature). Performance degrades at 60 °C (140 °F) or higher Charge cable: -30 °C (-22 °F) ― 50 °C (122 °F) (ambient tem-
perature)
Storage temperature Onboard charger: -40 °C (-40 °F)
― 65 °C (149 °F) (coolant
temperature), -40 °C (-40 °F) ― 85 °C (185 °F) (ambient tem-
perature)
Charge cable: Vehicle guaranteed temperature
Applicable standards Onboard charger:
　EN/IEC 61851-1, EN/IEC 61851-21,
EN/IEC 61851-23, UL 2202
Charge cable: NFPA 70, NFPA 79, SAE -J 1772, UL 62, UL 817, UL
2231-1, UL 2231-2, UL 2251, UL 2594, CSA C22.2 No.280-16
Adapters Do not use an adapter on the charge plug and the charge con-
nector.
Do not use an extension cable.
▼ High Voltage Battery
Item
Specification
Type Lithium-ion battery
Specifications
Speci fications
9-3
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

ItemSpecification
Te m p e ra t u r e ra n g e Operation guaranteed temperature: -30 °C (-22 °F)
― 60 °C
(140 °F)
Storage guaranteed temperature: -40 °C (-40 °F) ― 70 °C
(158 °F)
▼ Lead-acid Battery
Item
Specification
Lead-acid battery
*112V -42Ah/20HR
*1 Check the battery installed on the vehicle and use a battery with an equal or
higher performance. However, the performance of the battery may vary even
among the same battery types, consul t an Authorized Mazda Dealer for
replacement.
▼ Lubricant Quality
Lubricant
Classification
Coolant FL-22 type
EV Transaxle fluid Mazda Original Oil ATF-FZ
Brake fluid SAE J1703 or FMVSS116 DOT-3
▼ Capacities
(Approximate Quantities)
Item
Capacity
Coolant 4.3 L (4.5 US qt, 3.8 Imp qt)
EV Transaxle fluid 1.55 L (1.64 US qt, 1.36 Imp qt)
Check oil and fluid levels with dipsticks or reservoir gauges.
▼ Dimensions
Item
Vehicle specification
Overall length 4,393 mm (173.0 in)
Overall width 1,797 mm (70.7 in)
Overall height 1,574 mm (62.0 in)
Front tread 1,563 mm (61.5 in)
Rear tread 1,563 mm (61.5 in)
Wheelbase 2,653 mm (104.4 in)
Specifications
Speci fications
9-4
MX-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07