2022 MAZDA MODEL MX-30 EV power

NOTE
The tire sealant cannot be reused.
Purchase new tire sealant at an
Authorized Mazda Dealer.
The emergency flat tire repair kit
cannot be used in the following
cases.
Consult an Authorized Mazda
Dealer.
The period of eff ective use for the
tire sealant has expired. (The
period of eff ectiveness is indicated
on the bottle label.)
The tear or puncture exceeds
about 4 mm (0.16 in).
The damage has occurred to an
area of the tire other than the
tread.
The vehicle has been driven with
nearly no air remaining in the tire.
The tire has come o ff the wheel
rim.
Damage to the wheel rim has
occurred.
The tire has 2 or more punctures.
▼ Using the Emergency Flat Tire
Repair Kit
1. Park on a level surface o
ff the
right-of-way and set the parking
brake.
2. Shift the selector lever to the P position and switch the power
switch to OFF.
3. Turn on the hazard warning flasher.
4. Unload passengers and luggage,
and remove the emergency flat tire
repair kit.

5. Shake the sealant bottle to mix the contents. Then extend the injection
hose.

1. Injection hose
CAUTION
Do not shake the bottle excessively.
Otherwise, the sealant could spray
out of the injection hose, and if the
sealant contacts clothing or other
objects, you may not be able to
remove it.
NOTE
The sealant hardens easily and
injecting it will be di fficult under
cold weather conditions (0 °C
(32 °F) or below). Warm the
sealant inside the vehicle to
facilitate injection.
If Trouble Arises
Flat Tire
7-5
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

6. Pull out the air compressor hoseand the air compressor plug from
the air compressor.

1. Compressor hose
7. Install the air compressor hose which was pulled out of the air
compressor to the injection valve of
the bottle.

1. Compressor hose
2. Valve
3. Injection hose
CAUTION
Make sure that the air compressor
switch is off before inserting the air
compressor hose to the injection
valve of the bottle. If the air
compressor hose is not installed to
the injection valve of the bottle
securely, the sealant may leak.
8. Remove the valve cap from the valve of the flat tire, install the
injection hose to the tire valve, turn
the sleeve to the right, and tighten
it.

1. Valve
2. Valve cap
3. Injection hose
9. Install the bottle to the air
compressor and press it in until the
left and right tabs are engaged
securely.

1. Tabs
10.Insert the air compressor plug into the accessory socket inside the
vehicle and switch the power
switch to ACC.
If Trouble Arises
Flat Tire
7-6
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Changing a Flat Tire
▼Locking Lug Nuts
If your Mazda is equipped with the
optional antitheft wheel lug nuts, a
special key must be
used to unlock the
locking lug nut for each wheel. The key
is stored in the glove compartment,
center console storage, storage box, or
trunk. Register the key and lug nuts
with the lock manufacturer by filling
out the registration card and mailing it
in using the accompanying envelope. If
the key is lost, consult an Authorized
Mazda Dealer or use the lock
manufacturer’s order form to order a
new key.
Antitheft wheel lug nuts cannot be
installed on a steel wheel spare tire.
When installing a temporary spare tire,
use one of the original lug nuts in place
of the locking lug nut. The original lug
nuts are stored inside your Mazda.
1. Antitheft lug nut
2. Special key
To remove an antitheft lug nut
1. Obtain the special key for the antitheft lug nut.
2. Place the special key on top of the antitheft lug nut, and be sure to
hold the key square to it. If you
hold the key at an angle, you may
damage both key and nut. Do not
use a power impact wrench.
3. Place the lug wrench on top of the key and apply pressure. Turn the
wrench counterclockwise.
To install the antitheft lug nut
1. Place the special key on top of the
nut, and be sure to hold the key
square to it. If you hold the key at
an angle, you may damage both key
and nut. Do not use a power
impact wrench.
2. Place the lug wrench on top of the special key, apply pressure, and
turn it clockwise.
Nut tightening torque
N·m (kgf·m, ft·lbf) 108
―147 (12 ―14,
80 ―108)
If Trouble Arises
Flat Tire
7-10
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

What to do when
charging is not possible
▼ What to do when charging is not
possible
If trouble arises while charging such as
not being able to charge the high
voltage battery, refer to the following
table. If the problem cannot be solved
even after checking the following table,
there may be a problem with the
vehicle or charger. Contact an
Authorized Mazda Dealer.
Charging is not possible.

Cause
Action
The selector
lever is in a
position
other than P. Shift the selector lever to the P
position.
The high
voltage bat-
tery is al-
ready fully
charged. Charging is not performed when
the high voltage battery is al-
ready fully charged.
The high
voltage bat-
tery temper-
ature is ex-
tremely high
or low. Check the high voltage battery
temperature gauge in the instru-
ment cluster. If the high voltage
battery temperature gauge is in
the red or blue range, charging
may not be possible.
The
Lead-acid
battery is
depleted. If the instrument cluster does not
turn on even if the power switch
is switched ON, the Lead-acid
battery may be depleted. Charge
or replace the Lead-acid battery.
Normal charging is not possible.

Cause
Action
The outlet
has no pow-
er. Check if a ground-fault circuit in-
terrupter has operated or if a
power outage occurred. If the
power source has a timer func-
tion, electrical power may not be
supplied to the outlet until the
time set to supply power.
The charge
plug is not
properly
plugged into
the outlet. Check if the charge plug is prop-
erly plugged into the outlet.
The charge
connector is
not properly
connected. Check if the charge connector is
properly connected.
Charging
timer is set. Cancel the charging timer using
EV Settings in Mazda Connect,
or the charging timer cancella-
tion function.
Troubleshooting for functions using a
Smartphone or computer
If you are having trouble with the
remote function service, such as when
the remote function does not work,
refer to the Connected Service owner’s
manual.
If Trouble Arises
Troubleshooting for Charging
7-11
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Keep all flames and sparks away from open
lead-acid battery cells because
hydrogen gas is produced from open le ad-acid battery cells while charging the
lead-acid battery or adding lead-acid battery fluid:
Flames and sparks near open lead-acid ba ttery cells are dangerous. Hydrogen gas,
produced during normal lead-acid battery operation, could ignite and cause the
lead-acid battery to explode. An explodin g lead-acid battery can cause serious burns
and injuries. Keep all fl ames including cigarettes and sparks away from open
lead-acid battery cells.
Do not jump-start a frozen lead-acid battery or one with a low fluid level:
Jump-starting a frozen lead-acid battery or one with a low fluid level is dangerous. It
may rupture or explode, causing serious injury.
Connect the negative cable to a good ground point away from the lead-acid
battery:
Connecting the end of the second jumper ca ble to the negative (–) terminal of the
depleted lead-acid battery is dangerous.
A spark could cause the gas around the lead-acid battery to explode and injure
someone.
Route the jumper cables away from parts that will be moving:
Connecting a jumper cable near or to moving part (cooling fans) is dangerous. The
cable could get caught when the EV system starts and cause serious injury.
CAUTION
 Connect the booster cables with extreme care.
 Do not jump-start the vehicle with the charging cable connected to your vehicle.
Otherwise, the vehicle could be damaged.
 Do not use your vehicle as a booster vehicle.
NOTE
If your lead-acid battery is depleted, make sure that the booster vehicle's battery is
a lead-acid battery.
1. Move the booster vehicle so that its lead-acid battery is as close as possible to your vehicle's lead-acid battery.
2. Make sure that the power switch is switched OFF.
If Trouble Arises
Depleted Lead-acid Battery
7-13
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

Fully Discharged High Voltage Battery
▼Actions to take if the remaining high voltage battery power is completely
depleted
If the high voltage battery power is comp
letely depleted, the EV system stops and
the vehicle cannot be driven.
Stop the vehicle in a safe place and contact an Authorized Mazda Dealer.
If Trouble Arises
Fully Discharged High Voltage Battery
7-16
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

If a Warning Light TurnsOn or Flashes
▼If a Warning Light Turns On or
Flashes
If any warning light turns on/
flashes,
take appropriate action for each light.
There is no problem if the light turns
o ff, however if the light does not turn
o ff or turns
on/flashes again, consult
an Authorized Mazda Dealer.
WARNING
If the warning light/indicator light
turns on or flashes, park the vehicle in
a safe place immediately and take
appropriate measures.
Continuing to drive the vehicle while
ignoring the illumination/ flashing of
the warning light/indicator light is
dangerous because a problem may
occur to a vehicle system, or it could
lead to an accident.
The details for some warnings can be
viewed on the center display or
multi-information display in the
instrument cluster.
Center display
1. Select “Information” on the home
screen.
2. Select “Vehicle Status Monitor”.
3. Select the applicable warning to view the warning details.
Multi-information display
1. Press the INFO switch on the steering switch to display the
warning indication screen.
Refer to Multi-information Display
on page 4-11.
▼Brake System Warning Indication/
Warning Light
This warning has the following
functions:
Warning light inspection
For an operation check, make sure that
the light turns on when the power
switch is switched on and turns o
ff a
few seconds later, or when the EV
system is started.
When the light turns on
If the brake system warning light
remains illuminated the brake fluid
may be low or there could be a
problem with the brake system. Park
the vehicle in a safe place immediately
and contact an Authorized Mazda
Dealer.
Refer to Inspecting Brake Fluid Level on
page 6-12.
WARNING
Do not drive with the brake system
warning light illuminated. Contact an
Authorized Mazda Dealer to have the
brakes inspected as soon as possible:
Driving with the brake system warning
light illuminated is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this light
remains illuminated, after checking
that the parking brake is fully released,
have the brakes inspected
immediately.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-21
MX -30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07

“EV System Malfunction. Have the
Vehicle Inspected” is displayed
The indication/light displays/turns on
if the system has a problem.
Have your vehicle inspected by an
Authorized Mazda Dealer.
“EV System Malfunction. Stop the
Vehicle in a Safe Location” is
displayed
The indication/light displays/turns on
if the system has a problem.
Park the vehicle in a safe place
immediately and contact an
Authorized Mazda Dealer.
“Electrical Leakage in EV System
Detected Stop the Vehicle in a Safe
Location” is displayed
The indication/light displays/turns on
if the system has a problem.
Park the vehicle in a safe place
immediately and contact an
Authorized Mazda Dealer.
WARNING
Do not open the hood:
If you touch something in the motor
compartment, it could lead to an
electrical shock resulting in an
accident.
CAUTION
If the light turns on while driving, the
EV system cannot be started when the
power switch is switched OFF once.
▼ High Voltage Battery Temperature
War n in g I nd ic at ion
“Excessive High Voltage Battery
Temperature. Drive Slowly” is
displayed
The indication displays if the high
voltage battery temperature is
excessively high.
Drive slowly to reduce load on the high
voltage battery.
Stop the vehicle in a safe place if
necessary. If the indication remains
displayed, the system may have a
problem. Have the vehicle inspected
by an Authorized Mazda Dealer.
“High Voltage Battery Temperature Is
Low Acceleration Is Limited” is
displayed
The indication displays if the high
voltage battery temperature is
excessively low.
The vehicle speed may not increase
even if the accelerator pedal is
depressed because the motor output is
restricted.
If the indication remains displayed, the
system may have a problem. Have the
vehicle inspected by an Authorized
Mazda Dealer.
▼Remaining High Voltage Battery
Power Warning Indication/
Warning Light
“High Voltage Battery Is Low. Charge
Battery Soon” displays/turns on
The indication displays when the
remaining high voltage battery power
is low.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-23
MX
-30_8JD4-EA -21G_Edition2_new 2021-5-18 14:38:07