
2335-5. Using the other interior features
RC F Owner's Manual
5
Interior features
■Before programming
●Install a new battery in the transmitter.
●The battery side of the transmitter must
be pointed away from the HomeLink®.
Press the appropriate HomeLink®
button. The HomeLink
® indicator light
should turn on.
The status of the opening and closing
of a garage door is shown by the indi-
cators.
Opening
Closing
This function is only available if the garage
door opener motor used is a compatible
device. (To check device compatibility,
refer to www.homelink.com.)
The indicators can operate within
approximately 820 ft. (250 m) of the garage door. However, if there are
obstructions between the garage door
and the vehicle, such as houses and
trees, feedback signals from the
garage door may not be received.
To recall the previous door operation
status, press and release either
HomeLink
® buttons and
or and simulta-
neously. The last recorded status will
be displayed for 3 seconds.
Press and hold the 2 outside buttons
for 10 seconds until the HomeLink
®
indicator light changes from continu-
ously lit (orange) to rapidly flashing
(green).
If you sell your vehicle, be sure to erase the
programs stored in the HomeLink
® mem-
ory.
Operating HomeLink®
ColorStatus
Orange (flashing)Currently open-
ing/closing
GreenOpening/closing has
completed
Red (flashing)Feedback signals
cannot be received
A
B
Erasing the entire HomeLink®
memory (all three codes)

237
RC F Owner's Manual
6
6
Maintenance and care
Maintenance and care
.6-1. Maintenance and careCleaning and protecting the vehi-cle exterior ................................ 238
Cleaning and protecting the vehi- cle interior ................................. 243
6-2. Matte paint care guide (if equipped)
Basic knowledge about matte clear coat ................................... 247
Washing your vehicle .............. 251
Frequently Asked Questions ........................................................ 252
6-3. Maintenance Maintenance requirements .. 255
General maintenance ............. 256
Emission inspection and mainte- nance (I/M) programs ......... 259
6-4. Do-it-yourself maintenance Do-it-yourself service precautions........................................................ 260
Hood............................................... 262
Positioning a floor jack............ 263
Engine compartment............... 265
Tires ................................................. 271
Tire inflation pressure.............. 277
Wheels........................................... 279
Air conditioning filter...............280
Electronic key battery .............. 281
Checking and replacing fuses ........................................................ 283
Headlight aim.............................. 285Light bulbs....................................
286

2386-1. Maintenance and care
RC F Owner's Manual
6-1.Maintenance and care
Unlike a vehicle with a normal clear
coat, special care is necessary to pro-
tect the appearance of a vehicle with a
matte clear coat. (P.247, 251, 252)
Working from top to bottom, liber-
ally apply water to the vehicle body,
wheel wells and underside of the
vehicle to remove any dirt and dust.
Wash the vehicle body using a
sponge or soft cloth, such as a
chamois.
For hard-to-remove marks, use car
wash soap and rinse thoroughly with
water.
Wipe away any water.
Wax the vehicle when the water-
proof coating deteriorates.
If water does not bead on a clean surface,
apply wax when the vehicle body is cool.
■CFRP (Carbon Fiber Reinforced Plas-
tic) part (if equipped)
●As the CFRP parts may change color if
they are exposed to ultraviolet rays for
extended periods of time, Lexus recom-
mends that your vehicle be stored in a
place where it will not be exposed to
direct sunlight.
●Do not use wax that contains abrasives.
■Black stainless steel window moldings
The stainless steel window moldings are
made of black oxide co ated stainless steel.
When cleaning the vehicle, do not scrub the
moldings with an abrasive cleaner as their
finish may be damaged or the color may
change.
■Self-restoring coat*
The vehicle body has a self-restoring coat-
ing that is resistant to small surface
scratches caused in a car wash etc.
●The coating lasts for 5 to 8 years from
when the vehicle is delivered from the
plant.
●The restoration time differs depending on
the depth of the scratch and outside tem-
perature.
The restoration time may become shorter
when the coating is warmed by applying
warm water.
●Deep scratches caused by keys, coins,
etc. cannot be restored.
●Do not use wax that contains abrasives.
*: CFRP parts (if equipped) do not have a self-restoring coat.
■Automatic car washes(vehicles without
CFRP parts)
●Fold the mirrors before washing the vehi-
cle. Start washing from the front of the
vehicle. Make sure to extend the mirrors
before driving.
●Wash the vehicle with the active rear
wing retracted. If the vehicle is washed
with the active rear wing raised, depend-
ing on the type of automatic car wash, the
brushes of the automatic car wash may
become stuck on the ac tive rear wing. In
Cleaning and protecting the
vehicle exterior
Perform cleaning in a manner
appropriate to each component
and its material.
Matte paint care guide (body)
Cleaning instructions

2416-1. Maintenance and care
RC F Owner's Manual
6
Maintenance and care
WARNING
■Precautions regarding the exhaust
pipes
As exhaust gases cause the exhaust
pipes to become quite hot, do not touch
the exhaust pipes while the engine is run-
ning or immediately after the engine is
turned off.
When washing the vehicle, be careful not
to touch the exhaust pipes until they have
cooled sufficiently, as touching hot
exhaust pipes can cause burns.
■Precaution regarding the rear
bumper with Blind Spot Monitor (if
equipped)
If the paint of the rear bumper is chipped
or scratched, the system may malfunc-
tion. If this occurs, consult your Lexus
dealer.
NOTICE
■Application of coatings to the vehicle
body (vehicles wi th CFRP parts)
Do not apply any kind of coating to the
vehicle body as doing so may damage
the paint or reduce its durability.
■To prevent paint deterioration and
corrosion on the body and compo-
nents (aluminum wheels etc.)
●Wash the vehicle immediately in the
following cases:
• After driving near the sea coast
• After driving on salted roads
• If coal tar or tree sap is present on the paint surface
• If dead insects, in sect droppings or
bird droppings are present on the
paint surface
• After driving in an area contaminated with soot, oily smoke, mine dust, iron
powder or chemical substances
• If the vehicle becomes heavily soiled with dust or mud
• If liquids such as benzene and gasoline are spilled on the paint surface
●If the paint is chipped or scratched,
have it repaired immediately.
●To prevent the wheels from corroding,
remove any dirt and store in a place
with low humidity when storing the
wheels.
■Cleaning the exterior lights
●Wash carefully. Do not use organic
substances or scrub with a hard brush.
This may damage the surfaces of the
lights.
●Do not apply wax to the surfaces of the
lights. Wax may cause damage to the
lenses.
■To prevent damage to the windshield
wiper arms
When lifting the wiper arms away from
the windshield, pull the driver side wiper
arm upward first, an d repeat for the pas-
senger side. When re turning the wipers
to their original position, do so from the
passenger side first.
■When using an automatic car wash
(vehicles with rain-sensing windshield
wipers)
Set the wipers to the intermittent wind-
shield wipers. ( P.143)
If AUTO mode is selected, the wipers
may operate and the wiper blades may
be damaged.
■When using a high pressure car wash
●When washing the vehicle, do not
spray the camera or its surrounding
area directly with a high pressure
washer. Shock applied from high pres-
sure water may cause the device to not
operate normally.

2446-1. Maintenance and care
RC F Owner's Manual
Remove dirt and dust using a vac-
uum cleaner.
Wipe off any excess dirt and dust
with a soft cloth dampened with
diluted detergent.
Use a diluted water so lution of approxi-
mately 5% neutral wool detergent.
Wring out any excess water from
the cloth and thoroughly wipe off all
remaining traces of detergent.
Wipe the surface with a dry, soft
cloth to remove any remaining
moisture.
Allow the leather to dry in a shaded
and ventilated area.
■Caring for leather areas
Lexus recommends cleani ng the interior of
the vehicle at least twice a year to maintain
the quality of the vehicle’s interior.
Remove dirt and dust using a vac-
uum cleaner.
Wipe it off with a soft cloth damp-
ened with neutral detergent diluted
to approximately 1%.
Wring out any excess water from
the cloth and thoroughly wipe off
remaining traces of detergent and
water.
NOTICE
■Preventing damage to leather sur-
faces
Observe the following precautions to
avoid damage to and deterioration of
leather surfaces:
●Remove any dust or dirt from leather
surfaces immediately.
●Do not expose the vehicle to direct
sunlight for extended periods of time.
Park the vehicle in the shade, espe-
cially during summer.
●Do not place items made of vinyl, plas-
tic, or containing wax on the uphol-
stery, as they may stick to the leather
surface if the vehicle interior heats up
significantly.
■Water on the floor
Do not wash the vehicle floor with water.
Vehicle systems such as the audio system
may be damaged if water comes into
contact with electrical components such
as the audio system above or under the
floor of the vehicl e. Water may also
cause the body to rust.
■When cleaning the inside of the wind-
shield
Do not allow glass cleaner to contact the
lens. Also, do not touch the lens.
(
P.153)
■Cleaning the inside of the rear win-
dow
●Do not use glass cleaner to clean the
rear window, as this may cause dam-
age to the rear window defogger
heater wires or antenna. Use a cloth
dampened with lukewarm water to
gently wipe the window clean. Wipe
the window in strokes running parallel
to the heater wires or antenna.
●Be careful not to scratch or damage
the heater wires or antenna.
Cleaning the leather areas
Cleaning the synthetic leather
areas

2456-1. Maintenance and care
RC F Owner's Manual
6
Maintenance and care
It is recommended that regular mainte-
nance should be performed for areas
that are frequently touched to maintain
quality.
■Routine maintenance
This maintenance is most effective if
performed regularly (around once per
month).
1 Soak a cloth in lukewarm water
(approximately 104°F [40°C]),
wring it out thoroughly and then
wipe the entire body.
Wipe carefully so that the pile is not dishev-
eled. Be sure to prepare a clean cloth.
Once you have wiped the part with the
cloth, rinse it until it is completely clean
before using the cloth again.
2 Once it has dried, use a lint brush
or the like to comb the pile.
■When cleaning the artificial
leather (Alcantara®)
If liquid is spilled onto the surface,
apply tissue paper or the like to
absorb the liquid.
If any substance such as mud or cof-
fee dries and becomes stuck to the
surface, use a lint brush or the like to
lightly brush the dirty area and
remove the substance. Then, it is
recommended to clean the dried
substance from the surface using a
vacuum cleaner.
For oil-based substances, use a dry
cloth or tissue paper to wipe off the substance as much as possible,
while being careful not to spread it.
If the substance still cannot be
removed, use the following procedure
to remove it.
1 Liquid substances: Soak a cloth in
lukewarm water (approximately
104°F [40°C]), wring it out thor-
oughly and then wipe the dirty area
from the outside inward.
Wipe carefully so that the pile is not dishev-
eled. Be sure to prepare a clean cloth and
use the clean portion of it to clean the sur-
face.
Oil-based substances: Dab a cloth soaked
in benzene, lukewarm water or pure ethyl
alcohol (for drinking) within the dirty area
from the outside inward, and then dab a
dry cloth on the dirty area to absorb the
substance.
2 If the pile on the surface is dishev-
eled, use a lint brush or the like to
lightly brush the surface, and then
allow the surface to dry completely.
■To remove substances adhered to
the pile
To clean dust or other adhered sub-
stances, use a lint brush or the like to
lightly brush the area and remove the
substance. If the substance still cannot
be removed, use adhesive tape to
remove it.
*:Alcantara® is a registered trademark of
Alcantara S.p.A.
Cleaning the artificial leather
(Alcantara
®*) areas (if
equipped)
NOTICE
■When driving
Areas that are frequently touched are
more likely to attract dirt. Ensure that
your hands are clean before touching
anything.

2486-2. Matte paint care guide (if equipped)
RC F Owner's Manual
Normal clear coat
Cross section
Light
Clear
Base
Enlarged surface
Matte clear coat
Cross section
Light Matting agent
Clear
Base
Enlarged surface
Illustrations in this manual are simpli-
fied for explanation and may not repre-
sent the actual vehicle.
Glossiness of a surface is seen by the
human eyes by a difference in the
amount of light that reflects off the sur-
face.
A surface painted with normal clear
coat is flat and smooth. As the amount
of light that reflects off the surface is
large, the vehicle body will appear
glossy.
A surface painted with a matte clear
coat is slightly uneven due to the added
matting agent. As the light shining on
an uneven surface is diffused signifi-
cantly, the amount of light reflected is
small, making the vehicle body look not
glossy, with a unique texture.
Difference between general
clear coat and matte clear coat
A
B
C
A
B
C
D

2496-2. Matte paint care guide (if equipped)
RC F Owner's Manual
6
Maintenance and care
If the painted surfaces of the vehicle
are dirty, wash the vehicle immediately.
(Washing your vehicle P.251)
Dirt
Due to the slight unevenness, matte
clear coat surfaces are more likely to
trap dirt and other foreign matter com-
pared to normal clear coat surfaces. If dirt or foreign matter is left on the
vehicle, it may settle into the textured
surface of the matte clear coat, making
it more difficult to remove. Additionally,
as the surface of the matte clear coat
will become more flat when dirty, the
vehicle body will start to look glossy,
ruining the textured finish.
Therefore, make sure to clean the vehi-
cle regularly and not allow dirt to
remain on the vehicle for extended
periods of time.
If dirt or foreign matter is allowed to
settle and cannot be cleaned off with
normal washing, it will be necessary to
remove the dirt with the upper layer of
the textured finish and then to repaint
the entire part.
Ask your Lexus dealer for details.
■Materials that may become difficult to
remove
The following are likely to settle into the
vehicle body and should be cleaned off
immediately.
Cleaning and protecting the vehicle exterior
A