2022 KIA STINGER ECO mode
[x] Cancel search: ECO modePage 15 of 70
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Lane Keeping Assist (LKA)†6
Lane Keeping Assist is designed to detect the lane markers on the road with a front view camera on the windshield, and may assist the driver ’s steering to help keep the vehicle in the lane . When turned on, the instrument cluster
indicator will initially illuminate white . It will remain white when the vehicle is traveling slower than 40 mph or when the system does not detect the lane markers . When the system detects the lane markers and can assist the steering, the LK A icon will illuminate green .
If LK A detects that you are moving outside of your lane, the system may give an audible warning and display Lane Departure Warning on the instrument cluster . If the vehicle continues to move outside of the lane, LK A may provide steering, trying to prevent the vehicle from moving outside its lane .
LK A is the operating mode by default when the Lane Safety button* A is depressed to ON . To activate/deactivate LK A , press A .
There are three available modes:
•Assist: LK A will automatically assist the driver ’s steering when lane departure is detected to help prevent the vehicle from moving out of its lane
•Warning Only: LK A will warn the driver with an audible warning when lane departure is detected . The driver must steer the vehicle
•Off: LK A will turn off . The B indicator light will turn off on the cluster
•All systems will operate under the following conditions:
–The vehicle speed exceeds approximately 40 mph
–
LK A recognizes both sides of the lane markers the vehicle is traveling in
–
The vehicle is between the lane markers
Lane Keeping AssistLane Keeping AssistLane Keeping Assist
Lane Keeping Assist is not a substitute for safe driving and may not always warn the driver if the vehicle is driven outside of its lane . Always drive safely and use caution .
For illustrative purposes only . Your actual display, buttons and/or features may vary . Actual User Settings steps may vary by model .
Refer to section 5 in the Owner’s Manual for more information .
When the front-view camera does not detect the lane traveling in, the lanes are not illuminated gray
When the front-view camera detects the lane traveling in, both lanes are illuminated gray
Lane Keeping Assist
When the front-view camera detects the vehicle moving outside of the lane it is traveling in, a vehicle crossing lane indicator will blink, either on the left or right lane (as shown in both images above)
(But ton located on driver ’s panel, left of the steering wheel)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Lane Keeping Assist (LKA) Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED13
REMINDERS:
•
LK A will not issue a warning if the turn signal or hazard signal is activated
•
LK A will return to its previous state when the ignition is cycled
•
LK A is not a substitute for safe and proper driving . Always drive safely and use caution
•
LK A may not always aler t the driver if the vehicle is about to be driven outside of its lane
A
B
Page 18 of 70
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Driver Attention Warning (DAW)†7
Driver Attention Warning is designed to alert the driver if it detects inattentive driving practices and, in certain situations, can give a warning signal to take a break from driving .
•Inattentive Driving Warning: DAW will inform the driver of the driver ’s attention level and will recommend taking a break when it falls below a certain level
•Leading Vehicle Departure Alert: DAW will inform the driver when the front vehicle departs from a stop
If DAW is activated, the DAW information A will appear on the Instrument Cluster LCD when you select the Driving Assist menu in User Settings . A message, “Consider taking a break,” B appears on the LCD and a warning sounds to suggest the driver take a break when the driver ’s attention level
becomes low C .
DAW User Settings:
To turn DAW on/off, with the ignition on, press the Mode button D on the Steering Wheel and go to User Settings in the Instrument Cluster . Then go to Driver Assistance and select Driver Attention Warning .
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then press Vehicle on the screen to enter Vehicle Settings
REMINDERS:
•
The set-up of DAW will be maintained, as selected, when the ignition is cycled
•
When activated, DAW does not display the “Consider taking a break ” message when the total trip driving time is less than 10 minutes
•DAW will enter a standby mode if the camera does not detect the lanes
Refer to section 5 in the Owner’s Manual for more information .
Consider taking a break
Attention Level
High
Driver Attention Warning is not a substitute for safe driving and may not detect all instances of inattentive driving practices . Failure to pay attention to travel conditions and vehicle operation could result in loss of vehicle control . Always drive safely and use caution .
RESOKSET
(But ton layout on right of steering wheel)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Driver Attention Warning (DAW) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED16STINGER FEATURES & FUNCTIONS GUIDE
AB
C
D
Page 20 of 70
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Smart Cruise Control is designed to maintain a predetermined distance from vehicles detected ahead by automatically adjusting the driving speed as needed . When traffic is detected, the vehicle will slow down to maintain a
set distance behind traffic without depressing the accelerator or brake pedal .
With SCC on and activated, the vehicle distance set, and the system detects a vehicle slowing or stopping, the system can bring the vehicle to a complete stop . When the vehicle ahead starts to move forward, SCC re-engages . If the vehicle ahead stops for more than 3 seconds, the accelerator pedal or the RES+ button must be pressed to start moving the vehicle .
Smart Cruise Control will adjust acceleration based on the drive mode selected in the Drive Mode Integrated Control system .
Press the Driving Assist button* on the Steering Wheel A to activate and the speed will be set to the current vehicle speed . SCC may decrease the speed to maintain the distance with the vehicle in front .
To set/adjust the SCC speed:
•Press the Driving Assist button A to turn the system ON . The CRUISE indicator will illuminate on the instrument cluster
•Accelerate/decelerate to the desired speed
•Press the R E S + / S E T– button B to set the speed . Press the R E S + / S E T– button B up/down to increase/decrease the set speed
To set the vehicle distance:
•Press the Vehicle Distance button C on the steering wheel
•
Each time you press C the vehicle distance will change D, indicated by the number of bars that appear on the display E
To pause/resume SCC operation: Depress the brake pedal or press the Pause/Resume button* B . The
cruise indicator on the instrument cluster will change .
To turn SCC OFF: Press the Driving Assist button A . The CRUISE indicator on the instrument cluster will turn OFF .
To adjust the sensitivity of SCC: Press the mode button F on the Steering Wheel . With the OK button H, select Drive Assistance, then SCC Response . Then select Fast, Normal or Slow .
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 5 in the Owner’s Manual for more information .
CRUISE
CANCEL
RESOKSET
RESOKSETCRUISE60MPH
(Distances are approximate and var y depending on vehicle speed)
(Display on LCD screen)
172ft130ft
82ft
106ft
Smart Cruise Control (SCC)†6
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Smart Cruise Control with Stop & Go Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED18STINGER FEATURES & FUNCTIONS GUIDE
AD
E
F
HB
CF
Page 21 of 70
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Smart Cruise Control (SCC)†6 (Continued)
REMINDERS:
•
CRUISE indicator must be ON in order to operate SCC
•
SCC remains ON when ignition is cycled . The speed set ting will need to be reset when ignition is cycled
•
The distance set tings are approximations and may var y depending on vehicle speed . See the owner ’s manual for more information
•
SCC is also canceled when the driver ’s door is opened, gear shift is changed out of D (Drive), Electronic Parking Brake (EPB) is activated and various other conditions . See owner ’s manual for other conditions
•
If SCC is left on, it can be activated inadver tently . Keep the system off when not in use to avoid set ting a speed which the driver is not aware of
•
SCC is a supplemental system and is not a substitute for safe driving . It is the responsibilit y of the driver to always check the speed and distance to the vehicle ahead
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED19
•If your vehicle speed is bet ween 0-20 mph when you press the Driving Assist but ton to turn SCC on, the set speed will be set to 20 mph
•When following a vehicle, the system can automatically adjust your cruise speed based on the vehicle detected in front . It will even bring the vehicle to a complete stop if necessar y . If the vehicle remains at a standstill for more than 3 seconds, you must depress the accelerator pedal or press the RES+/SET- but ton up/down to star t the vehicle
•To change the cruise control mode from SCC to standard cruise control, press and hold but ton F . Repeat to switch back to SCC mode . (SCC must not be activated to change modes)
QUICK TIPS
Page 22 of 70
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Lane Following Assist is designed to help ensure that the vehicle stays centered in its lane A by monitoring the detected lane markings ahead and adjust the steering . When driving, LFA can be switched on and off
by pressing the Driving Assist button B . When turned on, the instrument cluster indicator will initially illuminate white when turned ON . It will remain white when the system does not detect the lane markers . When LFA detects the lane markers and can assist the steering, the LFA icon will illuminate green C .
LFA will operate only when these conditions are met:
•LFA recognizes both sides of the lane markers the vehicle is traveling in
•The vehicle is traveling slower than 120 mph
LFA User Settings:
•
To go to User Settings in the Instrument Cluster, press the Mode button D on the Steering Wheel when the vehicle is at a standstill, gear shift is in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To enable LFA , when in User Settings, press the Move (OK) button E up/down and Select Driver Assistance then Driving Assist, and select Lane Following Assist . Press the OK button E
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
•
Some vehicles have a Lane Driving Assist / Lane Safety button* on the Driver ’s Panel or the Steering Wheel B . Press to activate Lane Following Assist
Lane Following Assist (LFA)†6
RESOKSET
RESOKSET
Images are for illustrative purposes only and may not reflect actual feature or operation .
LFA is supplemental . Do not solely rely on this system and always pay attention to the road and its conditions .
See section 5 in the Owner’s Manual for more detailed information, limitations and conditions .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Lane Following Assist (LFA) Video
QR CODE
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED20STINGER FEATURES & FUNCTIONS GUIDE
A
C
D
E
B
REMINDER: LFA is not a substitute for safe and proper driving . Always drive safely and use caution .
Page 23 of 70
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Rear View Monitor (RVM)†6
Rear View Monitor is a supplemental system that displays the view behind the vehicle through the audio head unit screen while the vehicle is in Reverse .
Rear View Monitor activates when the:
•Engine Start/Stop button is in the ON position
•Gear Shift Lever is in the R (Reverse) position
REMINDERS:
•
Through normal use and after inclement weather or washing, the rear camera may become dir t y . Use a clean, microfiber cloth to remove any dir t, debris or spots that may have accumulated on the lens
•
RVM is not a substitute for proper and safe backing-up procedures
•
RVM may not display ever y object behind the vehicle
•
Always drive carefully and use caution when backing up
P
R
N
D
AUTO
HOLD
DRIVE MODEOFF
The Rear View Monitor is not a substitute for proper and safe backing-up procedures . The Rear View Monitor may not display every object behind the vehicle . Always drive safely and use caution when backing up .
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 4 in the Owner’s Manual for more information .
The Surround View Monitoring (SVM) is only a supplemental device . Drivers should not rely solely on the SVM information when parking and backing up . Drivers should always pay attention and directly check the left/right and rear .
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFF
OFF
VIEW
P
Images are for illustrative purposes only and may not reflect actual feature or operation . See section 4 in the Owner’s Manual for more information .
(But ton located below gear shift)
Surround View Monitor (SVM)*†6
Surround View Monitor (SVM) is a parking support system that shows the areas around the front, rear, left and right sides of the vehicle via four cameras displayed onto the audio head unit screen
.
•
Press the Parking/ View button A to turn on Surround View Monitor . Press the button again to turn off the function
•
Other view modes can be selected by touching the view icons B on the Surround View Monitor screen
•
Surround View Monitor Auto On: With Driver Assistance > Parking Safety
> Surround View Monitor Auto On selected from the Settings menu, the front parking assist view screen is displayed when Parking Distance Warning warns the driver while driving in D (Drive)
To change the SVM settings, press the onscreen settings icon C, while SVM is operating .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Surround View Monitor (SVM) Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED21
A
B
CREMINDER: The SVM camera is equipped with an optical lens to provide a wider range of vision and may appear different from the actual distance .
•The Front View of SVM will turn off when the gear shift is moved into Park or Reverse or the Parking/ View but ton is pressed .
QUICK TIP
Page 25 of 70
ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Forward*/Reverse Parking Distance Warning (PDW)†6
Forward/Reverse Parking Distance Warning (PDW)* A is a supplemental system that is designed to assist the driver by chiming if an object is detected within the sensing areas in the front or rear of the vehicle when
moving forward or backing up .
When the Engine Start/Stop button is ON and the shift lever is in R (Reverse), the system is activated and the Forward/Reverse Parking Distance Warning (PDW)* button indicator is illuminated .
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFFOFF
P
3 F B S T F O T P S T T I P X O
' P S X B S E 3 F W F S T F 1 B S L J O H % J T U B O \
D F 8 B S O J O H J T O P U B T V C T U J U V U \
F G P S Q S P Q F S B O E T B G F C B D L J O H V Q \
Q S P D F E V S F T " M X B Z T E S J W F \
T B G F M Z B O E V T F D B V U J P O X \
I F O C B D L J O H V Q\
' P S X B S E 3 F W F S T F 1 B S L J O H % J T U B O \
D F 8 B S O J O H 1 % 8
\
N B Z O P U E F U F D U F W F S Z P C K F D U J O G S P O U P \
G P S C F I J O E U I F W F I J D M F
4 F F T F D U J P O J O U I\
F 0 X O F S s T . B O V B M G P S N P S F J O G P S N B U J P O
3 F G F S U P U I F J O T J E F G S P O U D P W F S G P S N P S F J O G P S N B U J P O P O 2 3 D P E F T X X X Z P V U V C F D P N , J B ' F B U V S F 7 J E F P T
Forward*/Reverse Parking Distance Warning (PDW) VIDEO
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED23
A
REMINDERS:
•
If the vehicle is moving at speeds over 6 mph, the system may not activate
•
When more than t wo objects are sensed at the same time, the closest one will be recognized first
•
For ward/Reverse Parking Distance Warning (PDW)* is not a substitute for proper and safe backing-up procedures . Always drive safely and use caution when backing up . For ward/Reverse Parking Distance Warning (PDW)* may not detect ever y object behind or in front of the vehicle
Page 27 of 70
DRIVER’S PANEL
P
R
N
D
AUTO
HOLD
DRIVE MODE
OFF
OFF
VIEW
P
For more information on Electronic Stability Control (ESC) and its specific features and operations, please refer to section 5 in the Owner’s Manual .
Electronic Stability Control (ESC)†8 / Traction Control System (TCS)†8
Electronic Stability Control (ESC) is designed to help stabilize the vehicle during certain cornering maneuvers
. Traction Control System (TCS) can help improve traction . It is a good idea to keep both ESC and TCS turned
on for daily driving whenever possible .
Press the ESC button A to turn Traction Control System OFF/ON .
To turn both Electronic Stability Control and Traction Control System OFF, press and hold the ESC button for more than 3 seconds . Press again to turn ON .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electronic Stability Control Video
QR CODE
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED25
DRIVER’S PANEL
REMINDERS:
•
ESC is active by default at vehicle star t-up . When ignition is cycled, ESC will turn ON again
•
The ESC indicator light in the instrument cluster will be lit momentarily whenever ESC is activeA
Refer to section 4 in the Owner’s Manual for more information .
Instrument Cluster Control (Instrument Panel Dimmer)
With parking lights/headlights ON, press B (+) or (-) to adjust the brightness of the Instrument panel illumination .B
Refer to section 5 in the Owner’s Manual for more information .
Hill-start Assist Control (HAC)†8
Hill-start Assist Control (HAC) is designed to prevent the vehicle from rolling backwards when accelerating from a stop while on a steep incline .
HAC automatically activates whether ESC is OFF or ON but does NOT activate when ESC has malfunctioned .
REMINDERS:
•
HAC does not operate when the gear shift is in P (Park) or N (Neutral) position
•
HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
•
In the event of HAC system malfunction, see an Authorized Kia Dealer for ser vice
•When HAC is active (e .g ., during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator . HAC does not replace the need to apply brakes while stopped on an incline
•
HAC provides a t wo-second delay before the vehicle may star t rolling backwards
QUICK TIPS