2022 KIA SORENTO lights

30*IF EQUIPPEDSORENTO FEATURES & FUNCTIONS GUIDE
To operate:
•Move lever Up/Down D to change Wiper modes
•Push switch E to adjust Intermittent Wipe Speed
•Pull lever to spray and wipe F
Windshield Wipers & Washers
MIST: Single wipe
OFF: Wiper off
INT/AUTO*: Intermittent Wipe/Rain Sensing*
LO: Slow wipe
HI: Fast wipe
OFFOFF
AUTO
OFFOFF
AUTO
MIST
OFF
AUTO
LO
HI
HIREARLO
OFF
MIST OFF
AUTO
LO
HI
HIREARLO
OFF
MIST OFF
AUTO
LO
HI
HIREARLO
OFF
MIST OFF
AUTO
LO
HI
HIREARLO
OFF
HI: Fast wipe
LO: Slow wipe
OFF: Wiper off
Rear Wiper & Washer*
To operate:
•Rotate Rear Wiper switch to change Wiper modes G
•Push to spray and wipe H
B
C
D
E
GH
F
A
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wipers Stalk Video
QR CODE
•Moving switch E up increases intermit tent wipe frequency and wipe speed . Moving switch down decreases frequency of wipes
•Set the wiper to the OFF position when the wiper is not in use
QUICK TIPS
On Rear Wipers, the intermit tent wipe function is not adjustable . LO and HI sets wiper speed .
QUICK TIP
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
Turn Signals & Fog Lights*
To operate:
•Slightly move lever up/down to activate One-Touch Lane Change Signal A
•Turn Signals – Move lever Up/Down for Right/Left Turn Signal B
•Fog Lights – Press toggle switch C to turn Fog Lights ON/OFF
REMINDER: Headlights must be ON for Fog Light operation
One-Touch Lane Change Signal is activated by briefly pressing the Turn Signal Lever up/down slightly for less than 1 second and then releasing A . The lane change signal will blink 3 times .
To turn the One-Touch Lane Change Signal OFF/ON, go to User Settings Mode in the LCD Instrument Cluster modes .
Refer to section 4 in the Owner ’s Manual for more information . For illustrative purposes only . Your actual display, but tons and/or features may var y .
One-Touch Lane Change Signal

55†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
See section 4 in the Owner ’s Manual for more information.
Images are for illustrative purposes only and may not reflect actual feature or operation.
The Smart Liftgate with Auto Open can be operated from several controls to either open, close or lock the Liftgate. The Smart Liftgate with Auto Open will close the Liftgate, lock all doors and Liftgate and then arm the vehicle.
When the Smart Key fob is on your person and you are near the back of the vehicle, within close proximity, the hazard lights will blink and a chime will sound for about 3 seconds as an alert that the Smart Power Liftgate is about to open. Then the alert system will blink and chime two additional times before opening the Smart Power Liftgate.
The Smart Liftgate with Auto Open feature is off by default. To enable the Smart Power Liftgate, go to User Settings in the LCD Instrument Cluster modes.
REMINDERS:
•All doors are closed and locked after about 15 seconds
•The Smar t Liftgate with Auto Open feature will not operate when:
-
The doors are recently closed and locked, and the Smar t Key is still detected after 15 seconds near the vehicle or within 60 inches of the door handles
-A door is not locked or closed
-The Smar t Key is in the vehicle
•
Press any but ton on the Smar t Key fob during the Detect and Aler t stage, or move out of the detection area, to deactivate the Smar t Liftgate with Auto Open function
•
When the ignition is on, the Smar t Liftgate with Auto Open will only operate with the gear shift in the Park (P) position
•
The Smar t Key must be outside of the vehicle for the Smar t Liftgate with Auto Open to operate
•When closing, be mindful of any objects or persons
Smart Liftgate with Auto Open*†2 0
OTHER KEY FEATURES
OTHER KEY FEATURES
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Smart Power Liftgate Video
QR CODE
•
During the Smar t Liftgate with Auto Open aler t, the Smar t Liftgate with Auto Open can be deactivated with the Smar t Key by pressing any but ton on the key fob or moving away from the detection area
•
The open height and speed can be adjusted. For information on how to set the open height and speed, see your owner ’s manual
QUICK TIPS

56*IF EQUIPPEDSORENTO FEATURES & FUNCTIONS GUIDE
See section 4 in the Owner ’s Manual for more information .
Images are for illustrative purposes only and may not reflect actual feature or operation .
Map/Room Lamps
Automatic turn off function*
The interior lights automatically turn off approximately 30
seconds after the Engine Start/Stop button is OFF .
Map/Room Lamp Operation
•Press lens A to turn the Driver ’s/Passenger ’s Map Lamps ON/OFF . This light produces a spot beam for convenient use as a map lamp or as a personal lamp for the driver or the front passenger .
•Press button B to turn all the Map/Room Lamps ON/OFF
•
Press button C to turn the Map/Room Lamp ON, for 30 seconds, when a door is opened, unlocked from Smart Key or the ignition is turned OFF . When pressed and a door is opened, or doors are unlocked from the Smart Key, the Map and Room Lamps turn ON for approximately 30 seconds .
•Press button D to turn the Room Lamp ON/OFF
Panoramic Sunroof with Power Sunshade*
The Sunroof and Sunshade operation is controlled through multidirectional lever & push button switches E . The ignition
needs to be ON to operate the sunroof/sunshade .
REMINDER: The sunroof can be operated for approximately 30 seconds after the ignition is turned off . If the front doors are opened, the sunroof cannot be operated even within the 30-second period .
To slide the Sunshade and Sunroof:
Auto Open: Slide the lever E backward to the farthest position and release
Auto Close (Sunroof only): Slide the lever E forward to the farthest position (second detent) and release
Tilting the Sunroof open/closed:
Open/Raise: Push lever E upward
Close/Lower: Push lever E forward
Auto Close Sunroof and Sunshade: Slide the Sunroof lever E forward to the farthest position
PASSENGER
AIR BAGOFFPASSENGERAIR BAGOFF
PASSENGERAIR BAGOFF
PASSENGERAIR BAGOFFPASSENGERAIR BAGOFF
PASSENGERAIR BAGOFF
(Front overhead console)
(Center of cabin)
REMINDERS:
•
The Sunshade needs to remain OPEN while Sunroof is open and vehicle is moving
•
Do not adjust the sunroof or sunshade while driving . This could result in loss of control of the vehicle
•When closing, be mindful of any objects or persons
See section 4 in the Owner ’s Manual for more information .
Images are for illustrative purposes only and may not reflect actual feature or operation .
A
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Sunroof Operation Video
QR CODE
•When doors are unlocked by the Smar t Key*, the lamp turns ON for approximately 30 seconds
•If your vehicle is equipped with the theft alarm system, the interior lights automatically turn off approximately 5 seconds after the system is in the armed stage
•Using interior lights for an extended period of time may cause bat ter y discharge
QUICK TIPS
To stop the Sunroof/Sunshade at any position, push or pull the Sunroof control lever in any direction .
QUICK TIP
OTHER KEY FEATURES
OTHER KEY FEATURES
A
C
DE
B

57†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS .
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will delete all information) .
To program non-rolling and rolling code garage door openers and other devices:
1 . Press and hold the A and C buttons simultaneously until the indicator light G begins to flash (to reprogram buttons, skip this step)
2 . Press and hold the desired button A B C and hold the button on the transmitter while it is approximately 1 to 3 inches away from the mirror . The HomeLink® Indicator light E will flash rapidly once the frequency signal has been successfully programmed
To finish programming rolling code garage door openers, complete these steps:
3 . Locate the “learn” or “smart ” button on the garage door ’s motor head unit . Press and release the button and complete Step 4 within 30 seconds
4 . Firmly press and release the programmed HomeLink® button up to three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons .
Erasing programmed buttons:
Press and hold the A and C buttons simultaneously for approximately 20 seconds, and then release both buttons within 30 seconds .
The HomeLink® / Auto-Dimming Rearview Mirror* is designed to reduce glare from a vehicle’s headlights located in the rear and also connect up to three electronic transmitters into one location .
HomeLink®†3 with Auto-Dimming Rearview Mirror*
A HomeLink® Channel 1
B HomeLink® Channel 2
C HomeLink® Channel 3
D Garage Door Opener Status Indicator: Closing or Closed
E HomeLink® Operation Indicator
F Garage Door Opener Status Indicator: Opening or Open
G HomeLink® User Interface Indicator
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit . For more information, go to w w w .HomeLink .com or call (800) 355-3515 .
Images are for illustrative purposes only and may not reflect actual feature or operation .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Homelink® Support Video
QR CODE
•You can reprogram a single HomeLink® but ton by repeating Step 2
•Erasing the programmed but tons will delete all trained transmit ters
QUICK TIPS
OTHER KEY FEATURES
OTHER KEY FEATURES
BC
D
EG
F
A