2022 KIA EV6 tow

6*IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
Low Battery Warning – When the high-voltage battery level reaches 8% or less, this warning message appears on the LCD and the warning indicator light on the instrument cluster illuminates. Charge the high-voltage battery immediately.
Power limited due to low EV battery temperature. Charge battery – When the outside temperature is low and you turn the vehicle on or off, this warning message may appear on the LCD. If the battery level is low and the vehicle is parked outside for a long time, vehicle power may be limited. Charging battery before driving helps increase power.
Stop vehicle and check power supply – When there is a failure in the power supply system, this warning message appears on the LCD. Park the vehicle in a safe location and have it towed to the nearest Kia dealer for inspection.
EV Battery Overheated! Stop Vehicle – When the high-voltage battery temperature is too high, this warning message will appear on the LCD. Stop the vehicle and turn off the Power button so that the battery temperature decreases.
Charge immediately. Power limited – When the high-voltage battery level reaches 3% or less, this warning message appears on the LCD,
the warning indicator light on the instrument cluster illuminates and the power down warning light turns ON simultaneously.
The vehicle’s power will be reduced to minimize the energy consumption of the high-voltage battery. Charge the high-voltage battery immediately.
Power limited – This warning message appears when the vehicle’s power is limited for the following reasons:
1. When the high-voltage battery is below a
certain level, or voltage is decreasing
2. When the temperature of the motor or high-voltage battery is too high or too low
3. When there is a problem with the cooling system or a failure that may interrupt normal driving
Charge Warning Messages on Instrument Panel LCD
REMINDERS:
•
When these warning messages are displayed, do not accelerate or star t the vehicle suddenly
•
All stored driving information (except Odometer and Range) is reset if the bat ter y is disconnected
Low EV BatteryEV Battery Overheated!Stop Vehicle
Power limiteddue to low EV batterytemperature.Charge battery
Stop vehicle andcheck power supplyCharge immediately.Power limited
Power limited
Not all warnings and messages are displayed. These illustrations are for demonstration purposes only. Some messages may appear differently. See section 1 in the Owner ’s Manual for more information.
INSTRUMENT CLUSTER
INSTRUMENTCLUSTER

42*IF EQUIPPEDEV6 FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
STEERING

WHEEL CONTROLS
OFFAUTO
AUTO
OFFAUTO
AUTO
OFFAUTO
AUTO
OFFAUTO
AUTO
Headlight position ON
Parking light position
AUTO*Auto Light Position / Day time Running Lights / High Beam Assist
OFFHeadlight OFF position
Headlights & High Beams
To operate:
•Rotate lever to change the Headlight function
•Push lever to turn High Beams ON
•Pull lever to flash Headlights/High Beams
High Beam Assist (HBA)
AUTO Light position – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle.
Daytime Running Lights (DRL) – DRL may help others to see the front of your vehicle during the day. The lights will be on automatically when the ignition or POWER button* is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
•Parking brake is applied
•Engine is turned off
Turn Signals
To operate:
Turn Signals - Slightly move lever up/down to activate One-Touch Lane Change Signal. Move lever Up/Down for Right/Left Turn Signal
One-Touch Lane Change Signal is activated by briefly pressing the Turn Signal Lever slightly up or down for less than 1 second and then releasing. The lane change signal will blink 3-7 times.
To change how many times (3/5/7 times) the Lane Change Signal blinks, go to User Settings Mode in the LCD Instrument Cluster modes.
PUSH
PULL
For illustrative purposes only. Your actual display, but tons and/or features may var y. Refer to section 5 in the Owner ’s Manual for more information.
REMINDERS:
•
HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously. If the lever is pulled toward you while HBA is operational, HBA will turn off
•
If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•The DRL system turns off when parking brake is applied
•DRL only operates during the day time
The High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from oncoming vehicles and road conditions.
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you. The High Beam Assist indicator will illuminate.
High Beam Assist does not operate below certain speeds, or in some lighting and driving conditions. Please be aware of your surroundings and exercise proper road etiquette when operating a vehicle
using the high beams.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
High Beam Assist (HBA) Video
Steering Wheel Controls Video
QR CODE

43†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
STEERING WHEEL CONTROLS
STEERING

WHEEL CONTROLS
Tilt/Telescoping
Steering Wheel†2 0
To adjust the Steering Wheel, push the lock-release lever B down and adjust the desired angle C and distance D.
When finished, pull the lock-release lever B up to lock Steering Wheel in place.
Do not at tempt to adjust steering wheel position when vehicle is in motion as this may cause you to lose control of the vehicle.
Refer to section 5 in the Owner ’s Manual for more information.
For illustrative purposes only. Your actual display, but tons and/or features may var y.
It may be helpful to pull/push bot tom of Steering Wheel towards/away from you to adjust desired distance.
QUICK TIP
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Wipers and Wiper Stalk Video
Tilt/Telescoping/Heated Steering Wheel Video
QR CODE
•Pressing switch A up increases Intermit tent wipe frequency and wipe speed. Pressing switch A down decreases frequency of wipes
•Set the wiper to OFF position when the wiper is not in use
QUICK TIPS
AUTO
Windshield Wipers & Washers
To operate Windshield Wipers and Washers:
•Move lever Up/Down to change front Wiper modes
•Press switch A Up (fast) / Down (slow) to adjust Intermittent Wipe Speed
•Pull lever to spray and wipe front windshield
Rain Sensing (Auto Control Wipe):
•The rain sensor located on the upper end of the windshield glass senses the amount of rainfall and controls the wiping cycle for the interval selected. The more it rains, the faster the wiper operates. When the rain stops, the wiper stops
•To vary the speed setting, press the Wiper Switch A up/down
•If the wiper lever is set in AUTO mode when the Power button is ON, the wiper will operate once to per form a self-check of the system
WINDSHIELD MIST: Single wipeOFF: Wiper offAUTO: Auto control wipe (rain sensing)LO: Slow wipeHI: Fast wipe
Refer to section 4 in the Owner ’s Manual for more information.
A
C
D
B

47†LEGAL DISCL AIMERS ON BACK INSIDE COVER | *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
Kia Connect Activation Video
Kia Connect & Kia Access App Video
Kia Connect Assistance Video
QR CODE
Driving while distracted can result in a loss of vehicle control that may lead to an accident, severe bodily injur y, and death. The driver ’s primar y responsibilit y is in the safe and legal operation of a vehicle, and any handheld devices, other equipment, or vehicle systems which take the driver ’s eyes, at tention and focus away from the safe operation of a vehicle or which are not permissible by law should never be used during operation of the vehicle.
Kia Connect A - Press to connect to a virtual assistant to hear information about the Kia Connect features
Roadside Assist B - Press to connect to a Roadside Assistant where you can request vehicle towing services
REMINDER: These but tons may be located in the rear view mirror or the overhead console.
Kia Connect Assistance*†1
Kia Connect Activation*†1
Follow these steps to activate your Kia Connect system:
1. Enter the activation screen on your vehicle’s head unit:
a. Press SETUP key
b. Press Kia Connect icon
c. Press Activate Kia Connect
2.
Read and agree to Terms of Service and Privacy Policy and press SUBMIT
3.
Enter number or email address to receive a verification code, then press SUBMIT
4.
Follow these steps to receive your verification code using your phone SMS or email:
a. Check your phone SMS or email for verification code
b. Open the link in your SMS or email. A page will open requesting that you create your account
N o t e : If you already have a Kia Owners Portal account using the email or phone number as your login ID, you will need to provide your password prior to receiving the verification code.
c. Enter your first name, last name, email, phone number, an account password, and click CREATE ACCOUNT. A page will open displaying your verification code
d. Enter the code in the head unit and press ACTIVATE
e. Go back to the page with your verification code and press “I have entered my verification code.” A link will be provided to download the Kia Access App from your app store. After installing the app, log in and enjoy
For fur ther Kia Connect operations, refer to the Car Infotainment System Quick Reference Guide.
Kia Connect may be unavailable for model year 2022 and later vehicles sold or purchased in Massachuset ts.
OFFPASSENGER
AIR BAG
(But tons located on overhead console*)
OFFPASSENGERAIR BAG
%SJWJOH
XIJMF
EJTUSBDUFE
DBO
SFTVMU
JO
B
MPTT
PG
WFIJDMF
DPOUSPM
UIBU
NBZ
MFBE
UP
BO
BDDJEFOU

TFWFSF
CPEJMZ
JOKVS Z

BOE
EFBUI
5IF
ESJWFS sT
QSJNBS Z
SFTQPOTJCJMJU Z
JT
JO
UIF
TBGF
BOE
MFHBM
PQFSBUJPO
PG
B
WFIJDMF

BOE
BOZ
IBOEIFME
EFWJDFT

PUIFS
FRVJQNFOU

PS
WFIJDMF
TZTUFNT
XIJDI
UBLF
UIF
ESJWFS sT
FZFT

BU UFOUJPO
BOE
GPDVT
BXBZ
GSPN
UIF
TBGF
PQFSBUJPO
PG
B
WFIJDMF
PS
XIJDI
BSF
OPU
QFSNJTTJCMF
CZ
MBX
TIPVME
OFWFS
CF
VTFE
EVSJOH
PQFSBUJPO
PG
UIF
WFIJDMF
INFOTAINMENT SYSTEMS
INFOTAINMENTSYSTEMS
AB

57 *IF EQUIPPEDALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS.
Refer to the inside front cover for more information on QR codes.www.youtube.com/KiaFeatureVideos
2nd-Row Seats Video
Rear Occupant Alert with Door Monitoring Video
QR CODE
Rear Occupant Alert (ROA) with Door Monitoring†1 1
Rear Occupant Alert (ROA) with Door Monitoring can help alert the driver when a rear passenger may be left in the vehicle. The alert will be a message on the Instrument Cluster LCD stating to “Check rear seats” B and an alert will sound.
The factory default is set to OFF. To turn the system ON or OFF, go to Vehicle Settings on the Infotainment System by selecting VEHICLE, then select Convenience, then Rear Occupant Alert and check/uncheck the box.
REMINDERS:
•
Always be sure to check the passenger areas before leaving the vehicle
•
ROA uses a rear door opened/closed histor y, which is reset after the driver turns the vehicle off, exits the vehicle and locks the door remotely. So even if a rear door does not reopen, Rear Occupant Aler t (ROA) aler t can occur
(Message on Cluster Display)
When engaged, Rear Occupant Aler t is not a substitute for one’s at tention and may not detect all movement within the vehicle. Always check the vehicle interior when exiting the vehicle.
See section 5 in the Owner ’s Manual for more information.
(Seat fold lever located in rear cargo area)
(Seat fold lever located at bot tom side of seat)
Folding Rear Seats
To Fold:
1. Ensure the belt strap is out of way of the Seatback folding
2. Adjust the Front Seatback to the upright position and lower the rear headrest(s) to the lowest position
3. Pull on the Rear Seat recliner lever A, then fold the seat toward the front
To Unfold:
1. Pull the Rear Seat recliner lever A and lift the Seatback backward until it clicks firmly in place
2. Return the rear seat belt to the proper position
REMINDER: Always make sure the Seatback is locked in place when unfolded.
For illustration purposes only. Actual vehicle might be slightly different.
Refer to section 4 in the Owner ’s Manual for more information.
SEATING
S E AT I N G
It may be necessar y to adjust the Front Seatbacks to fully lower rear seats.
QUICK TIP
B
A