2022 HYUNDAI I10 Screen

5-46
Convenient features
OAC3059031TU
„Front
„Rear
OAC3059032TU
A : Wiper speed control
· MIST (
) – Single wipe
· OFF (O) – Off
· INT (---) – Intermittent wipe
(if equipped)
· LO (1) – Low wiper speed
· HI (2) – High wiper speed
B : Intermittent wipe time
adjustment
C : Wash with brief wipes
D : Rear wiper/washer control/
Wash with brief wipes
·
– Wash with brief wipes
· ON (
) – Continuous wipe
· OFF (O) – Off
Windscreen wipers
Operates as follows when the ignition
switch is in the ON position.
MIST (
) : For a single wiping cycle,
push the lever upward
and release. The wipers
will operate continuously
if the lever is held in this
position.
OFF (O) : Wiper is not in operation.
INT (---) : Wiper operates intermit-
tently at the same wiping
intervals. To vary the speed
setting, turn the speed con-
trol knob (B).
LO (1) : The wiper runs at a lower
speed.
HI (2) : The wiper runs at a higher
speed.
i Information
If there is heavy accumulation of snow
or ice on the windscreen, defrost the
windscreen for about 10 minutes, or
until the snow and/or ice is removed
before using the windscreen wipers to
ensure proper operation.
If you do not remove the snow and/or
ice before using the wiper and washer,
it may damage the wiper and washer
system.
WIPERS AND WASHERS

5-47
05
Windscreen washers
OAC3059034TU
In the OFF (O) position, pull the lever
gently toward you to spray washer
fluid on the windscreen and to run the
wipers 1-3 cycles. The spray and
wiper operation will continue until you
release the lever. If the washer does
not work, you may need to add wash-
er fluid to the washer fluid reservoir.
WARNING
When the outside temperature is
below freezing, ALWAYS warm the
windscreen using the defroster to
prevent the washer fluid from
freezing on the windscreen and
obscuring your vision which could
result in an accident and serious
injury or death.
CAUTION

5-48
Convenient features
OAC3059039TU
OAC3059040R
5HDU9LHZ0RQLWRUZLOODFWLYDWHZKHQ
the ignition switch is in the ON posi-
tion and the shift lever is in the R
(Reverse) position.
This is a supplemental system that
shows behind the vehicle through the
audio or infotainment system screen
whilst backing-up.
WARNING
Rear View Monitor is not a safety
device. It only serves to assist the
driver in identifying objects direct-
ly behind the middle of the vehicle.
The camera does NOT cover the
complete area behind the vehicle.
WARNING

5-55
05
OAI3059118
The mode selection knob controls the
direction of the air flow through the
ventilation system.
Air can be directed to the floor, dash-
board outlets, or windscreen. Five
symbols are used to represent Face,
Bi-Level, Floor, Floor-Defrost and
Defrost air position.
Face-Level (B, ')
Air flow is directed toward the upper
body and face. Additionally, each out-
let can be controlled to direct the air
discharged from the outlet.
Bi-Level (B, C, ')
Air flow is directed towards the face
and the floor.
Floor-Level (A, C, ')
Most of the air flow is directed to the
floor, with a small amount of the air
being directed to the windscreen,
side window defrosters and side
vents.
Floor/'efrost-Level (A, C, ')
Most of the air flow is directed to the
floor and the windscreen with a small
amount directed to the side window
defrosters and side vents.
'efrost-Level (A, ')
Most of the air flow is directed to the
windscreen with a small amount of air
directed to the side vents.

5-57
05
i Information
2perating the system primarily in
Fresh mode is recommended. 8se
Recirculation mode temporarily only
when needed.
Prolonged operation of the heater in
Recirculation mode and without the
A/C 21 can cause fogging of the wind-
screen.
In addition, prolonged use of the A/C
21 in Recirculation mode may result
in excessively dry, dehumidified air in
the cabin and may promote formation
of musty vent odor due to stagnant air.
WARNING

5-58
Convenient features
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning
ON with the temperature control
knob set to heat in order to dehu-
midify the air before it enters into
the cabin.
If the windscreen fogs up, select the
Floor & Defrost
mode or press
the Front Defrost
mode.
2peration 7ips

5-62
Convenient features
AUTOMATIC CLIMATE CONTROL SYSTEM
ãIF EQUIPPED
ä
OAI3059101I
1. Fan speed control knob
$&$LUFRQGLWLRQLQJEXWWRQ
5HFLUFXODWLRQPRGH)UHVKPRGH
4. Mode selection button
5. Rear window defroster button
(if equipped)6. Front windscreen defroster button
7. OFF button
8. Temperature control knob
9. AUTO (automatic control) button
10. Climate control screen

5-65
05
OAI3059113I
The mode selection button controls
the direction of the air flow through
the ventilation system.
The air flow outlet direction is cycled
as follows:
Face-Level (B, ')
Air flow is directed toward the upper
body and face. Additionally, each out-
let can be controlled to direct the air
discharged from the outlet.
Bi-Level (B, C, ')
Air flow is directed towards the face
and the floor.
Floor-Level (A, C, ')
Most of the air flow is directed to the
floor, with a small amount of the air
being directed to the windscreen and
side window defrosters.
Floor 'efrost (A, C, ')
Most of the air flow is directed to the
floor and the windscreen with a small
amount directed to the side window
defrosters.
OAI3059114I
'efrost-Level (A, ')
Most of the air flow is directed to the
windscreen with a small amount of air
directed to the side window defrost-
ers.
OAC3059103R
Instrument panel vents
The instrument panel vent air flow
FDQ EH GLUHFWHG XSGRZQ RU OHIWULJKW
XVLQJWKHYHQWDGMXVWPHQWOHYHU
7R FORVH WKH YHQW DGMXVWPHQW OHYHU
rotate it to the outer side till the end.
To open the vent, rotate it to the inner
side.