2022 HYUNDAI GENESIS G70 oil

09
9-25
AIR CLEANER
Filter Replacement
„2.0L T-GDI
OIK090011
„3.3L T-GDI (Passenger side)
OIK090012
„3.3L T-GDI (Driver side)
OIK090014
Do not attempt to wash or to rinse it, as
water will damage the filter.
If soiled, the air cleaner filter must be
replaced.
Have you visit an authorized retailer of
Genesis Branded products to replace air
cleaner filter.
Replace the filter according to the
Maintenance Schedule.
Information
If the vehicle is operated in extremely
dusty or sandy areas, replace the air
cleaner filter more often than the
usual recommended intervals (Refer
to “Maintenance Under Severe Usage
Conditions” section in this chapter).
NOTICE

[Do not drive with the air cleaner filter
removed. This will result in excessive
engine wear.

[When removing the air cleaner filter,
be careful that dust or dirt does not
enter the air intake, or damage may
result.

[We recommend that you use parts
for replacement from an authorized
retailer of Genesis Branded products.

Maintenance
9-30
Battery Usage
Recommendations

[Keep the battery securely mounted.

[Keep the battery top clean and dry.

[Keep the terminals and connections
clean, tight, and coated with
petroleum jelly or terminal grease.

[Rinse any spilled electrolyte from the
battery immediately with a solution of
water and baking soda.

[If the vehicle is not going to be used
for an extended time, disconnect the
battery cables.
Battery Replacement
„Trunk
OIK090022
When replacing the battery, disconnect
the negative (-) cable (1) and remove the
positive (+) battery fuse box (2). Remove
the trunk panel and spare wheel. Place
the spare wheel on the floor with the
finished side up so as not to damage.
Then remove the spare wheel bracket
(3) followed by the battery hold down
mounting bracket (4).
WARNING
Do not touch the vehicle's
lower area of the trunk
when the engine is running
or hot. It may cause serious
injury. Turn the engine OFF
and wait until the area is
cooled before replacing the
battery.
Battery Recharging
By battery charger
Should your vehicle's battery become
discharged either run the engine for
at least 60 minutes driving or at idle.
Alternatively you may connect a fully
automatic regulated charger to the
engine compartment front jumper posts
or at the battery in the trunk.
CAUTION
Do not use a manual unregulated
charger it may cause the battery
to overheat and create a potential
hazard.
WARNING
Always follow these instructions when
recharging your vehicle’s battery to
avoid the risk of SERIOUS INJURY or
DEATH from explosions or acid burns:

[Before performing maintenance or
recharging the battery, turn off all
accessories and stop the engine.

[Keep all flames, sparks, or smoking
materials away from the battery.

[Always work outdoors or in an area
with plenty of ventilation.

[Wear eye protection when checking
the battery during charging.

[The battery must be removed from
the vehicle and placed in a well
ventilated area.

[Watch the battery during charging,
and stop or reduce the charging
rate if the battery cells begin boiling
violently.

Maintenance
9-40
WARNING
The temperature grade for this tire is
established for a tire that is properly
inflated and not overloaded.
Excessive speed, under-inflation,
over-inflation, or excessive loading,
either separately or in combination,
can cause heat build-up and
possible sudden tire failure. This
may cause loss of vehicle control
resulting in an accident.
Tire Terminology and Definitions
Air pressure
The amount of air inside the tire
pressing outward on the tire. Air
pressure is expressed in pounds per
square inch (psi) or kilopascal (kPa).
Accessory weight
This means the combined weight
of optional accessories. Some
examples of optional accessories
are automatic transmission, power
seats, and air conditioning.
Aspect ratio
The relationship of a tire’s height to
its width.
Belt
A rubber coated layer of cords that
is located between the plies and the
tread. Cords may be made from steel
or other reinforcing materials.
Bead
The tire bead contains steel wires
wrapped by steel cords that hold the
tire onto the rim.Bias ply tire
A pneumatic tire in which the plies are
laid at alternate angles less than 90
degrees to the centerline of the tread.
Cold tire pressure
The amount of air pressure in a tire,
measured in pounds per square inch
(psi) or kilopascals (kPa) before a tire
has built up heat from driving.
Curb weight
This means the weight of a motor
vehicle with standard and optional
equipment including the maximum
capacity of fuel, oil and coolant, but
without passengers and cargo.
DOT markings
A code molded into the sidewall
of a tire signifying that the tire
is in compliance with the U.S.
Department of Transportation motor
vehicle safety standards. The DOT
code includes the Tire Identification
Number (TIN), an alphanumeric
designator which can also identify
the tire manufacturer, production
plant, brand and date of production.
GVWR
Gross Vehicle Weight Rating
GAWR FRT
Gross Axle Weight Rating for the
Front Axle.
GAWR RR
Gross Axle Weight Rating for the
Rear axle.

09
9-45
FUSES

v
Blade type

v
Cartridge type

v
Multi type

v
Midi typeNormal Blown
Normal Blown
Normal Blown
Normal Blown
OCK077071
A vehicle’s electrical system is protected
from electrical overload damage by
fuses.
This vehicle has 5 fuse panels, one
located in the driver’s side panel bolster,
the other in the engine compartment.
If any of your vehicle’s lights,
accessories, or controls do not work,
check the appropriate circuit fuse. If a
fuse has blown, the element inside the
fuse will be melted or broken.
If the electrical system does not work,
first check the driver’s side fuse panel.
Before replacing a blown fuse, turn the
engine and all switches off, and then
disconnect the negative battery cable.
Always replace a blown fuse with one of
the same rating.
If the replacement fuse blows, this
indicates an electrical problem.
Avoid using the system involved and
immediately consult an authorized
retailer of Genesis Branded products.
WARNING
NEVER replace a fuse with anything but
another fuse of the same rating.

[A higher capacity fuse could cause
damage and possibly cause a fire.

[Do not install a wire or aluminum
foil instead of the proper fuse -
even as a temporary repair. It may
cause extensive wiring damage and
possibly a fire.
NOTICE
Do not use a screwdriver or any other
metal object to remove fuses because
it may cause a short circuit and damage
the system.

09
9-53
Engine compartment fuse panel
Fuse NameFuse Rating Circuit Protected
ALT175A
225AAlternator, Fuse - F2,
Multi Fuse 1 - F4, F6, F7, F8, F9, F10, F11, F12, F13
C/FAN3
125A[G6DP - BLDC Motor] Cooling Fan Controller
GLOW[D4HB] Glow Relay Unit
START30A RLY. 7 (Start Relay)
C/FAN180A [BLDC Motor] Cooling Fan Controller
B+350AICU Junction Block (Fuse - F5, Leak Current Autocut
Device Fuse - F2, F4, F13, F14, F21, F22)
B+250A ICU Junction Block (Fuse - F27, F35, F43, F51, F52)
B+150A ICU Junction Block (Fuse - F28, F29, F37, F45, F53)
EOP50A [With ISG] Electric Oil Pump Module
ESP140A ESP Control Module
ESP240A ESP Control Module
BLOWER40A RLY. 6 (Blower Relay)
IG230A PCB Block (IG2 Relay)
MDPS100A MDPS Unit
B+460APCB Block
(Engine Control Relay, Fuse - F4, F5, F13, F22)
C/FAN260A [DC Motor] RLY. 9 (Cooling Fan Relay)
E-CVVT140A [G4KL] RLY. 8 (E-CVVT Relay)
TRAILER40A Trailer Connector
FUEL HEATER40A Diesel Junction Block (RLY.1 (Fuel Filter Heater Relay))
PTC HEATER130A Diesel Junction Block (RLY.2 (PTC Heater #1 Relay))
PTC HEATER230A Diesel Junction Block (RLY.3 (PTC Heater #2 Relay))
PTC HEATER330A Diesel Junction Block (RLY.4 (PTC Heater #3 Relay))

09
9-55
Engine compartment fuse panel
Fuse NameFuse Rating Circuit Protected
ESC310A ESP Control Module
ECU310A ECM
ECU215A ECM
HORN20A Horn Relay
WIPER130A Wiper Power Relay
TCU215A P/N Relay, TCM
SENSOR410AElectronic Oil Pump Module, Brake Vacuum Switch, E/R
Junction Block (RLY.1 (Brake Vacuum Relay))
TCU120A TCM
WIPER210A IBU, ECM
SENSOR115ARear Sub Junction Block (Fuel Pump Relay),
[D4HB] Rail Pressure Regulating Valve, DieseL Junction
Block (RLY.1 (Fuel Filter Heater Relay))
SENSOR520A[G4KL] Ignition Coil #1/#2/#3/#4
[G6DP] Ignition Coil #1/#2/#3/#4/#5/#6
[D4HB] Electronic Water Pump
MODULE10A Active Air Flap LH
ACTIVE HOOD10A Active Hood Lift Control Module
SENSOR110A[D4HB] Glow Relay Unit, Fuel Heater & Water Separator
Sensor
ECU120A ECM
SENSOR315A[G4KL] Oxygen Sensor (Up/Down)
[G6DP] Oxygen Sensor #1/#2/#3/#4
[D4HB] Lambda Sensor #1/#2, Electronic VGT Actuator,
Fuel Metering Unit, EGR Cooing Bypass Solenoid
Vlave, PTC Heater, Mid Nox Sensor, PM Sensor,
Rear Nox Sensor

Maintenance
9-56
Fuse NameFuse Rating Circuit Protected
SENSOR210AE/R Junction Block (RLY. 9 - Cooling Fan Relay),
[G4KL] Electronic Thermostat, Oil Control Valve, Purge
Control Solenoid Valve, Recirculation Control
Solenoid Valve
[G6DP] Electronic Thermostat, Oil Pressure Solenoid
Valve, Oil Control Valve #1/#2/#3/#4 (Intake/
Exhaust), Recirculation Control Solenoid Valve,
Purge Control Solenoid Valve, Variable Exhaust
Flap Actuator LH/RH
[D4HB] Oil Pump Solenoid Valve, Air Flow Sensor,
Crankshaft Position Sensor, Front Nox Sensor, Oil
Level Sensor, Stop Lamp Switch
B/ALARM10A E/R Junction Block (RLY. 2 - Burglar Alarm Horn Relay)
Relay
Type Relay No.Relay Name
MICRO RLY. 1 Vacuum OIK090033
MICRO RLY. 2 Burglar Alarm Horn Relay
MICRO RLY. 6 Blower Relay
MICRO RLY. 7 Start Relay
MICRO RLY. 8 E-CVVT Relay (G4KL)
MINI RLY. 9 Cooling Fan Relay

Maintenance
9-66
APPEARANCE CARE
Exterior Care
NOTICE
If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such
as a bumper, spoiler, garnish, lamp or
side view mirrors might be damaged
due to sunlight reflected from the
sign or building. To prevent damage of
the exterior plastic parts, you should
avoid parking in areas where light may
be reflected or use a car cover. (The
exterior plastic parts applied to your
vehicle may vary.)
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
Wa s h i n g
To help protect your vehicle’s finish from
rust and deterioration, wash it thoroughly
and frequently at least once a month
with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges
of the doors and rocker panels are kept
clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
High-pressure washing

[When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.

[Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.

[Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.