2022 HYUNDAI ELANTRA reverse

Maintenance
9-24
Filter Inspection
The cabin air filter should be replaced
according to the Maintenance Schedule.
If the vehicle is operated in severely
air-polluted cities or on dusty rough
roads for a long period, it should be
inspected more frequently and replaced
earlier. When you replace the cabin air
filter, replace it performing the following
procedure, and be careful to avoid
damaging other components.
Filter Replacement
OCN7080013OCN7080013
1. Push in both sides of the glove box as
shown. This will ensure that the glove
box stopper pins will get released
from its holding location allowing the
glove box to hang.
OCN7080014OCN7080014
2. Remove the cabin air filter case while
pressing the lock on the right side of
the cover.
OIK077021OIK077021
3. Replace the cabin air filter.
4. Reassemble in the reverse order of
disassembly.
NOTICE
Install a new cabin air filter in the correct
direction with the arrow symbol (
¢)
facing downwards, otherwise, it may be
noisy and the effectiveness of the filter
may be reduced.
CABIN AIR FILTER
CN7 HMA 9.indd 9-242020-12-03 9:42:22

09
9-45
Engine Compartment Panel Fuse
Replacement
„„Blade type fuseBlade type fuse
OCN7080021OCN7080021
„„Cartridge type fuseCartridge type fuse
OCN7080022OCN7080022
1. Turn the engine off.
2. Turn all other switches OFF.
3. Remove the fuse panel cover by
pressing the tap and pulling up.
4. Check the removed fuse; replace it
if it is blown. To remove or insert the
fuse, use the fuse puller in the engine
compartment fuse panel.
5. Push in a new fuse of the same
rating, and make sure it fits tightly in
the clips. If it fits loosely, consult an
authorized HYUNDAI dealer.
CAUTION
After checking the fuse box in the
engine compartment securely close
the fuse box cover inside the engine
compartment, until it clicks.
If the fuse box is not closed properly,
water may leak in side, possibly causing
a malfunction with the electrical
system.
Multi fuse (Main fuse)
OCN7080020OCN7080020
If the multi fuse is blown, it must be
removed as follows:
1. Turn off the engine.
2. Disconnect the negative battery
cable.
3. Remove the fuse panel cover by
pressing the tab and pulling it up.
4. Remove the nuts shown in the picture
above.
5. Replace the fuse with a new one of
the same rating.
6. Reinstall in the reverse order of
removal.
Information
,IWKHPXOWLIXVHLVEORZQFRQVXOWDQ
DXWKRUL]HG+<81'$,GHDOHU
CN7 HMA 9.indd 9-452020-12-03 9:42:28

09
9-57
Bulb type
OCN7080073LOCN7080073L
1. Remove the lamp assembly from the
vehicle by prying the lens and pulling
the assembly out.
2. Disconnect the bulb electrical
connector.
3. Separate the socket and the
lens parts by turning the socket
counterclockwise until the tabs on the
socket align with the slots on the lens
part.
4. Remove the bulb by pulling it straight
out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens
part.
7. Connect the bulb electrical connector.
8. Reinstall the lamp assembly to the
body of the vehicle.
Rear combination lamp bulb
replacement
„„Type AType A
OCN7090018NOCN7090018N
„„Type BType B
OCN7H090026NOCN7H090026N
„„Type CType C
OCN7H090025NOCN7H090025N
(1) Stop lamp (LED or bulb)
(2) Tail lamp (LED or bulb)
(3) Turn signal lamp
(4) Reverse lamp
(5) Rear side marker (LED or bulb)
CN7 HMA 9.indd 9-572020-12-03 9:42:32

09
9-59
Tail lamp/Stop lamp (Inner lamp)
(Bulb type)
1. Open the trunk.
2. Loosen the retaining screw of the
trunk lid cover and then remove the
cover.
OCN7080040OCN7080040
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Remove the bulb by pulling it out.
5. Insert a new bulb by inserting it into
the socket.
6. Reinstall the trunk lid cover by
pushing in the screw.
Reverse lamp (Inner lamp)
(Bulb type)
1. Disconnect the connector and then
remove the nuts by turning the nuts
counter clockwise.
2. Take the light assembly out.
OCN7080053OCN7080053
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Remove the bulb by pulling it out.
5. Insert a new bulb by inserting it into
the socket.
6. Install the light assembly to the trunk.
7. Reinstall the trunk lid cover by
pushing in the screw.
Stop/Tail lamp and rear side marker
(LED type)
If the LED lamp does not operate, we
recommend that you have the vehicle
checked by an authorized HYUNDAI
dealer.
CN7 HMA 9.indd 9-592020-12-03 9:42:36

Maintenance
9-60
High mounted stop lamp
replacement
OCN7080032OCN7080032
OAD075042OAD075042[A] : High mounted stop lamp
1. Open the trunk.
2. Remove the socket by turning it
counterclockwise until the tabs on the
socket align with the slots.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
License Plate Light Bulb
Replacement
OCN7080035OCN7080035
1. Using a flat-blade screwdriver gently
pry the lens cover from the lamp
housing.
2. Remove the bulb by pulling it straight
out.
3. Install a new bulb.
4. Reinstall in the reverse order.
CN7 HMA 9.indd 9-602020-12-03 9:42:36

Index
I-10
P
Parking Brake ...................................................................................................... 9-21
Checking the Parking Brake............................................................................. 9-21
R
Rear Cross-Traffic Collision Warning (RCCW) ............................................... 7-117
Function malfunction and limitations ............................................................ 7-121
Function operation.......................................................................................... 7-119
Function settings ............................................................................................ 7-118
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) ................................. 7-125
Function malfunction and limitations ............................................................ 7-131
Function operation.......................................................................................... 7-127
Function settings ............................................................................................ 7-126
Rear View Monitor (RVM) ................................................................................ 7-113
Function malfunction and limitations ............................................................ 7-116
Function operation.......................................................................................... 7-114
Function settings ............................................................................................ 7-114
Recommended Lubricants and Capacities........................................................... 2-13
Recommended SAE Viscosity Number ........................................................... 2-14
Reporting Safety Defects ..................................................................................... 2-18
Reverse Parking Collision-Avoidance Assist (PCA) ........................................ 7-138
Function malfunction and limitations ............................................................ 7-142
Function operation.......................................................................................... 7-141
Function settings ............................................................................................ 7-139
Reverse Parking Distance Warning (PDW) ...................................................... 7-135
Function malfunction and precautions .......................................................... 7-136
Function operation.......................................................................................... 7-136
S
Safe Exit Warning (SEW) ................................................................................... 7-60
Function malfunction and limitations .............................................................. 7-63
Function operation............................................................................................ 7-62
Function settings .............................................................................................. 7-61
Safety Messages..................................................................................................... 1-4
Scheduled Maintenance Services .......................................................................... 9-7
Maintenance Under Severe Usage Conditions ................................................. 9-11
Normal Maintenance Schedule (Smartstream G2.0 Atkinson) .......................... 9-8