2022 HYUNDAI ELANTRA N engine

09
9-47

v Cartridge type

v
Blade type

v Multi fuse Normal Blown
Normal Blown
Normal Blown
OTM078035OTM078035
A vehicle’s electrical system is protected
from electrical overload damage by
fuses.
This vehicle has 2 (or 3) fuse panels, one
located in the driver’s side panel bolster,
the other in the engine compartment
near the battery.
If any of your vehicle’s lights,
accessories, or controls do not work,
check the appropriate circuit fuse. If a
fuse has blown, the element inside the
fuse will be melted or broken.
If the electrical system does not work,
first check the driver’s side fuse panel.
Before replacing a blown fuse, turn the
engine and all switches off, and then
disconnect the negative battery cable.
Always replace a blown fuse with one of
the same rating.
If the replacement fuse blows, this
indicates an electrical problem.
Avoid using the system involved and
immediately consult an authorized
HYUNDAI dealer.
WARNING
NEVER replace a fuse with anything but
another fuse of the same rating.
• A higher capacity fuse could cause
damage and possibly cause a fire.
• Do not install a wire or aluminum
foil instead of the proper fuse -
even as a temporary repair. It may
cause extensive wiring damage and
possibly a fire.
NOTICE
Do not use a screwdriver or any other
metal object to remove fuses because
it may cause a short circuit and damage
the system.
FUSES
CN7 N HMA 9.indd 9-47 2021-09-08  9:30:24

Maintenance9-48
Instrument Panel Fuse
Replacement
OCN7N091011NOCN7N091011N
1. Turn the vehicle off.
2. Turn all other switches OFF.
3. Open the fuse panel cover.
4. Refer to the label on the inside of the fuse panel cover to locate the
suspected fuse location.
OCN7080018OCN7080018
5. Pull the suspected fuse straight out. Use the removal tool provided in the
engine compartment fuse panel.
6. Check the removed fuse; replace it if it is blown. Spare fuses are provided in
the engine compartment fuse panel.
7. Push in a new fuse of the same rating, and make sure it fits tightly in
the clips. If it fits loosely, consult an
authorized HYUNDAI dealer.
In an emergency, if you do not have a
spare fuse, use a fuse of the same rating
from a circuit you may not need for
operating the vehicle.
If the head lamp, turn signal lamp, tail
lamp, interior lamp doesn’t work and
the bulbs are undamaged, consult an
authorized HYUNDAI dealer.
CN7 N HMA 9.indd 9-48 2021-09-08  9:30:24

09
9-49
Engine Compartment Panel Fuse
Replacement
Blade type fuseBlade type fuse
OCN7080021OCN7080021
Cartridge type fuseCartridge type fuse
OCN7080022OCN7080022
1. Turn the engine off.
2. Turn all other switches OFF.
3. Remove the fuse panel cover by pressing the tap and pulling up.
4. Check the removed fuse; replace it if it is blown. To remove or insert the
fuse, use the fuse puller in the engine
compartment fuse panel.
5. Push in a new fuse of the same rating, and make sure it fits tightly in
the clips. If it fits loosely, consult an
authorized HYUNDAI dealer.
NOTICE
After checking the fuse panel in the
engine compartment, securely install
the fuse panel cover. You may hear a
clicking sound if the cover is securely
latched. If it is not securely latched,
electrical failure may occur from water
contact.
Multi fuse (Main fuse)
OCN7080020OCN7080020
If the multi fuse is blown, it must be
removed as follows:
1. Turn off the engine.
2. Disconnect the negative battery cable.
3. Remove the fuse panel cover by pressing the tab and pulling it up.
4. Remove the nuts shown in the picture above.
5. Replace the fuse with a new one of the same rating.
6. Reinstall in the reverse order of removal.
Information
If the multi fuse is blown, consult an
authorized HYUNDAI dealer.
CN7 N HMA 9.indd 9-49 2021-09-08  9:30:25

Maintenance9-54
OCN7N091013N
Engine compartment fuse panel
ODN8089017ODN8089017
Inside the fuse/relay box cover, you can
find the fuse/relay label describing fuse/
relay names and ratings.
Information
Not all fuse panel descriptions in this
manual may be applicable to your vehicle;
the information is accurate at the time of
printing. When you inspect the fuse panel
in your vehicle, refer to the fuse panel
label.
CN7 N HMA 9.indd 9-54 2021-09-08  9:30:27

09
9-55
Engine compartment fuse panel
Type Fuse NameFuse Rating Circuit Protected
MIDI
FUSE
-3 ALT
180A[G4FM/G4FG/G4NA] Alternator, (Fuse - F33, F34,
F35, F37)
[G4FP] Alternator, (Fuse - F33, F34, F35, F37)
MDPS1 100A MDPS Unit
MIDI
FUSE-2 COOLING
FAN2 80A [G4FP] Cooling Fan Controller
EOP 60A Electronic Oil Pump
RR HTD 50A Rear Glass Heated
MIDI
FUSE-1 B+5
60APCB Block (Engine Control Relay, Fuse - F1, F2,
F3, F4, F6)
B+1 60A ICU Junction Block (IPS2/IPS5/IPS6/IPS7/IPS14)
B+2 60AICU Junction Block (IPS1/IPS4/IPS8/IPS9/IPS10/
IPS13)
B+3 50AICU Junction Block (Fuse - F13, F14, F22, F23,
F32,F40, F41, Long Term Load Latch Relay)
BLOWER 40A BLOWER Motor, Multipurpose Check Connector
IG1 40A E/R Junction Block (RLY.4/6), Ignition Switch
IG2 40A E/R Junction Block (RLY.3/5), Ignition Switch
DCT1 60A TCU
PTC
HEATER 50A PTC HEATER
CN7 N HMA 9.indd 9-55
2021-09-08  9:30:27

Maintenance9-56
Engine compartment fuse panel
Type Fuse Name Fuse Rating Circuit Protected
FUSE POWER
OUTLET2 20
A Front Power Outlet
POWER
OUTLET3 20A Cigarette Lighter
VACUUM PUMP1 20A VACUUM PUMP, ESC
VACUUM PUMP2 10A Electronic Vacuum Pump
ECS 15A ECS Unit
E-LSD 20A LSD Control Module
E-CVVT3 20A ECM
E-CVVT2 20A ECM
E-CVVT1 40A E/R Junction Block (RLY.14)
DCT2 10A [G4FP] TCM
B+4 40AICU Junction Block (Fuse - F2, F25, F26, F34,
F43, F35 (IAU), F44, Power Window Relay)
AMS 10A Battery Sensor
TCU1 10A [M/T] Ignition Lock & Clutch Switch
FUEL PUMP 20A FUEL PUMP Motor
ABS1 40A ABS Control Module, ESP Control Module
ABS2 30AABS Control Module, ESP Control Module,
Multipurpose Check Connector
POWER
OUTLET1 40A E/R Junction Block (RLY.2)
WIPER 25A Wiper Motor
CN7 N HMA 9.indd 9-56
2021-09-08  9:30:27

09
9-57
Engine compartment fuse panel (PCB block) (Smartstream 2.5 GDI)
Type Fuse NameFuse Rating Circuit Protected
FUSE E
CS (15A)
15A ECS Unit
A/C 10A [G4FM] A/C Compressor
HORN 15A Horn, Horn Switch
IGN COIL 20A[G4FM/G4NA/G4FP] Ignition Coil #1~#4
[G4FG] Ignition Coil #1~#4
ECU3 10A PCM/ECM, [MT] IGN LOCK CLUTCH SW
SENSOR3 10A E/R Junction Block (RLY.8)
ECU2 15A PCM/ECM
SENSOR2 10A[G4FM] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, E/R Junction Block (RLY.1/11),
A/C Relay
[G4FG] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, E/R Junction Block (RLY.1/11)
[G4NA] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, Oil Pump Solenoid Valve, E/R
Junction Block (RLY.1/11)
[G4FP] Oil Control Valve (Intake/Exhaust),
Variable Intake Solenoid Valve, Purge Control
Solenoid Valve, RCV Control Solenoid Valve,
Cooling Fan Controller
[Theta 2 T-GDI] Oil Control Valve(Exhaust),
Electronic Water Pump, RCV, Cooling Fan, Purge
Control Solenoid Valve, A/C Comp RLY, Oil Level
Sensor, Canister Closing Valve, Active Exhaust
Valve
SENSOR1 15A Oxygen Sensor (UP/DOWN)
ABS3 10AABS Control Module, ESP Control Module,
Multipurpose Check Connector
ECU1 20A PCM/ECM
CN7 N HMA 9.indd 9-57
2021-09-08  9:30:28

Maintenance9-58
Consult an authorized HYUNDAI dealer
to replace most vehicle light bulbs. It is
difficult to replace vehicle light bulbs
because other parts of the vehicle must
be removed before you can get to the
bulb. This is especially true for removing
the headlamp assembly to get to the
bulb(s).
Removing/installing the headlamp
assembly can result in damage to the
vehicle.
WARNING
• Prior to working on a light, depress
the foot brake, shift to P (Park), apply
the parking brake, press the Engine
Start/Stop button to the OFF position
and take the key with you when
leaving the vehicle to avoid sudden
movement of the vehicle and to
prevent possible electric shock.
• Be aware the bulbs may be hot and
may burn your fingers.
NOTICE
Be sure to replace the burned-out bulb
with one of the same wattage rating.
Otherwise, it may cause damage to the
fuse or electrical wiring system.
NOTICE
To prevent damage, do not clean the
headlamp lens with chemical solvents
or strong detergents.
Information - Headlamp
desiccant (if equipped)
This vehicle is equipped with desiccant to
reduce fogging inside the headlamp due
to moisture. The desiccant is consumable
and its performance may change based on
the used period or environment. If fogging
inside the headlamp due to moisture
continues for a long time, consult an
authorized HYUNDAI dealer.
Information
The headlamp and tail lamp lenses could
appear frosty if the vehicle is washed after
driving or the vehicle is driven at night in
wet weather. This condition is caused by
temperature difference between the lamp
inside and outside and, it does not indicate
a problem with your vehicle. When
moisture condenses in the lamp, it will be
removed after driving with the headlamp
on. The removable level may differ
depending on lamp size, lamp position
and environmental condition. However, if
moisture is not removed, have your vehicle
inspected by an authorized HYUNDAI
dealer.
LIGHT BULBS
CN7 N HMA 9.indd 9-58 2021-09-08  9:30:28