2022 CHRYSLER 300 radiator cap

202IN CASE OF EMERGENCY
NOTE:The remote battery posts are viewed by standing
on the right side of the vehicle looking over the
fender. The positive battery post may be covered
with a protective cap. Lift up on the cap to gain
access to the positive battery post. Do not jump off
fuses. Only jump directly off positive post which
has a positive (+) symbol on or around the post.
See below steps to prepare for jump starting:

1. Apply the parking brake, shift the automatic transmission into PARK and cycle the ignition
to OFF.

2. Turn off the heater, radio, and all electrical accessories.
3. Pull upward and remove the protective cover over the remote positive (+) battery post.
4. If using another vehicle to jump start the battery, park the vehicle within the jumper
cables reach, set the parking brake, and make
sure the ignition is OFF.
JUMP STARTING PROCEDURE
NOTE:Make sure at all times that unused ends of jumper
cables are not contacting each other or either
vehicle while making connections.
Connecting The Jumper Cables

1. Connect the positive
(+) end of the jumper
cable to the remote positive (+)
post of the
discharged vehicle.

2. Connect the opposite end of the positive (+)
jumper cable to the positive (+) post of the
booster battery.
3. Connect the negative (-) end of the jumper
cable to the negative (-) post of the booster
battery.
4. Connect the opposite end of the negative (-)
jumper cable to the remote negative (-) post
(exposed metallic/unpainted post of the
discharge vehicle) located directly behind the
under-hood fuse box.
WARNING!
Do not allow vehicles to touch each other as this
could establish a ground connection and
personal injury could result.
WARNING!
Take care to avoid the radiator cooling fan
whenever the hood is raised. It can start
anytime the ignition switch is ON. You can be
injured by moving fan blades.
Remove any metal jewelry such as rings,
watch bands and bracelets that could make
an inadvertent electrical contact. You could be
seriously injured.
Batteries contain sulfuric acid that can burn
your skin or eyes and generate hydrogen gas
which is flammable and explosive. Keep open
flames or sparks away from the battery.
WARNING!
Failure to follow this jump starting procedure
could result in personal injury or property
damage due to battery explosion.
CAUTION!
Failure to follow these procedures could result in
damage to the charging system of the booster
vehicle or the discharged vehicle.
WARNING!
Do not connect the jumper cable to the negative
(-) post of the discharged battery. The resulting
electrical spark could cause the battery to
explode and could result in personal injury.

22_LX_OM_EN_USC_t.book Page 202

IN CASE OF EMERGENCY205
NOTE:There are steps that you can take to slow down an
impending overheat condition:
If your Air Conditioner (A/C) is on, turn it off. The
A/C system adds heat to the engine cooling
system and turning the A/C off can help remove
this heat.
You can also turn the temperature control to
maximum heat, the mode control to floor and
the blower control to high. This allows the heater
core to act as a supplement to the radiator and
aids in removing heat from the engine cooling
system.
MANUAL PARK RELEASE
To move the vehicle in cases where the
transmission will not shift out of PARK (such as a
depleted battery), a Manual Park Release is
available.
Follow these steps to use the Manual Park
Release:

1. Firmly apply the parking brake.

2. Remove the console storage bin to access the
Manual Park Release lever.

Manual Park Release Cover

WARNING!
You or others can be badly burned by hot engine
coolant (antifreeze) or steam from your radiator.
If you see or hear steam coming from under the
hood, do not open the hood until the radiator
has had time to cool. Never try to open a cooling
system pressure cap when the radiator or
coolant bottle is hot.
CAUTION!
Driving with a hot cooling system could damage
your vehicle. If the temperature gauge reads
HOT (H), pull over and stop the vehicle. Idle the
vehicle with the air conditioner turned off until
the pointer drops back into the normal range. If
the pointer remains on HOT (H), and you hear
continuous chimes, turn the engine off
immediately and call for service.
WARNING!
Always secure your vehicle by fully applying the
parking brake before activating the Manual Park
Release. In addition, you should be seated in the
driver's seat with your foot firmly on the brake
pedal when activating the Manual Park Release.
Activating the Manual Park Release will allow
your vehicle to roll away if it is not secured by the
parking brake, or by proper connection to a tow
vehicle. Activating the Manual Park Release on
an unsecured vehicle could lead to serious
injury or death for those in or around the vehicle.
7

22_LX_OM_EN_USC_t.book Page 205

224SERVICING AND MAINTENANCE
COOLING SYSTEM
Coolant Checks
Check engine coolant (antifreeze) protection every
12 months (before the onset of freezing weather,
where applicable). If the engine coolant is dirty, the
system should be drained, flushed, and refilled
with fresh Organic Additive Technology (OAT)
coolant (conforming to MS.90032) by an authorized dealer. Check the front of the radiator
for any accumulation of bugs, leaves, etc. If dirty,
clean by gently spraying water from a garden hose
vertically down the face of the condenser.
Check the coolant recovery bottle tubing for brittle
rubber, cracking, tears, cuts, and tightness of the
connection at the bottle and radiator. Inspect the
entire system for leaks. DO NOT REMOVE THE
COOLANT PRESSURE CAP WHEN THE COOLING
SYSTEM IS HOT.
Cooling System — Drain, Flush And Refill
NOTE:Some vehicles require special tools to add coolant
properly. Failure to fill these systems properly
could lead to severe internal engine damage. If any
coolant is needed to be added to the system
please contact an authorized dealer.
If the engine coolant (antifreeze) is dirty or
contains visible sediment, have an authorized
dealer clean and flush with Organic Additive
Technology (OAT) coolant (conforming to
MS.90032).
For the proper maintenance intervals
Úpage 210.
Selection Of Coolant
For further information Ú page 268.
NOTE:
Mixing of engine coolant (antifreeze) other than
specified Organic Additive Technology (OAT)
engine coolant, may result in engine damage
and may decrease corrosion protection. OAT
engine coolant is different and should not be
mixed with Hybrid Organic Additive Technology
(HOAT) engine coolant or any “globally compat -
ible” coolant. If a non-OAT engine coolant is
introduced into the cooling system in an emer -
gency, the cooling system will need to be
drained, flushed, and refilled with fresh OAT
coolant (conforming to MS.90032), by an autho -
rized dealer as soon as possible.
Do not use water alone or alcohol-based engine
coolant products. Do not use additional rust
inhibitors or anti-rust products, as they may not
be compatible with the radiator engine coolant
and may plug the radiator.
This vehicle has not been designed for use with
propylene glycol-based engine coolant. Use of
propylene glycol-based engine coolant is not
recommended.
Some vehicles require special tools to add
coolant properly. Failure to fill these systems
properly could lead to severe internal engine
damage. If any coolant is needed to be added to
the system please contact an authorized dealer.
WARNING!
You or others can be badly burned by hot
engine coolant (antifreeze) or steam from your
radiator. If you see or hear steam coming from
under the hood, do not open the hood until the
radiator has had time to cool. Never open a
cooling system pressure cap when the radi -
ator or coolant bottle is hot.
Keep hands, tools, clothing, and jewelry away
from the radiator cooling fan when the hood is
raised. The fan starts automatically and may
start at any time, whether the engine is
running or not.
When working near the radiator cooling fan,
disconnect the fan motor lead or turn the igni -
tion to the OFF position. The fan is tempera -
ture controlled and can start at any time the
ignition is in the ON position.

22_LX_OM_EN_USC_t.book Page 224

SERVICING AND MAINTENANCE225
Adding Coolant

Your vehicle has been built with an improved engine
coolant (OAT coolant conforming to MS.90032) that
allows extended maintenance intervals. This engine
coolant (antifreeze) can be used up to 10 years or
150,000 miles (240,000 km) before replacement.
To prevent reducing this extended maintenance
period, it is important that you use the same engine
coolant (OAT coolant conforming to MS.90032)
throughout the life of your vehicle.

Please review these recommendations for using
Organic Additive Technology (OAT) engine coolant
that meets the requirements of the manufacturer
Material Standard MS.90032. When adding
engine coolant:
We recommend using Mopar® Antifreeze/
Coolant 10 Year/150,000 Mile (240,000 km)
Formula OAT that meets the requirements of the
manufacturer Material Standard MS.90032.
Mix a minimum solution of 50% OAT engine
coolant that meets the requirements of the
manufacturer Material Standard MS.90032
and distilled water. Use higher concentrations
(not to exceed 70%) if temperatures below
−34°F (−37°C) are anticipated. Please contact
an authorized dealer for assistance.
Use only high purity water such as distilled or
deionized water when mixing the water/engine
coolant solution. The use of lower quality water
will reduce the amount of corrosion protection
in the engine cooling system.
NOTE:
It is the owner's responsibility to maintain the
proper level of protection against freezing
according to the temperatures occurring in the
area where the vehicle is operated.
Some vehicles require special tools to add
coolant properly. Failure to fill these systems
properly could lead to severe internal engine
damage. If any coolant is needed to be added to
the system, please contact a local authorized
dealer.
Mixing engine coolant types is not recom -
mended and can result in cooling system
damage. If HOAT and OAT coolant are mixed in
an emergency, have an authorized dealer drain,
flush, and refill with OAT coolant (conforming to
MS.90032) as soon as possible.
Cooling System Pressure Cap
The cap must be fully tightened to prevent loss of
engine coolant (antifreeze), and to ensure that
engine coolant will return to the radiator from the
coolant expansion bottle/recovery tank if
equipped. The cap should be inspected and cleaned if there
is any accumulation of foreign material on the
sealing surfaces.
Disposal Of Used Coolant
Used ethylene glycol-based coolant (antifreeze) is
a regulated substance requiring proper disposal.
Check with your local authorities to determine the
disposal rules for your community. To prevent
ingestion by animals or children, do not store
ethylene glycol-based coolant in open containers
or allow it to remain in puddles on the ground,
clean up any ground spills immediately. If ingested
by a child or pet, seek emergency assistance
immediately.
WARNING!
Do not open a hot engine cooling system.
Never add engine coolant (antifreeze) when
the engine is overheated. Do not loosen or
remove the cap to cool an overheated engine.
Heat causes pressure to build up in the
cooling system. To prevent scalding or injury,
do not remove the pressure cap while the
system is hot or under pressure.
Do not use a pressure cap other than the one
specified for your vehicle. Personal injury or
engine damage may result.
8

22_LX_OM_EN_USC_t.book Page 225

226SERVICING AND MAINTENANCE
Coolant Level
The coolant bottle provides a quick visual method
for determining that the coolant level is adequate.
With the engine off and cold, the level of the engine
coolant (antifreeze) in the bottle should be
between the ranges indicated on the bottle.
The radiator normally remains completely full, so
there is no need to remove the radiator/coolant
pressure cap unless checking for engine coolant
freeze point or replacing coolant. Advise your
service attendant of this. As long as the engine
operating temperature is satisfactory, the coolant
bottle need only be checked once a month.
When additional engine coolant is needed to
maintain the proper level, only OAT coolant that
meets the requirements of FCA Material Standard
MS.90032 should be added to the coolant bottle.
Do not overfill.
Cooling System Notes
NOTE:When the vehicle is stopped after a few miles/kilo -
meters of operation, you may observe vapor
coming from the front of the engine compartment.
This is normally a result of moisture from rain,
snow, or high humidity accumulating on the
radiator and being vaporized when the thermostat
opens, allowing hot engine coolant (antifreeze) to
enter the radiator. If an examination of your engine compartment
shows no evidence of radiator or hose leaks, the
vehicle may be safely driven. The vapor will soon
dissipate.
Do not overfill the coolant expansion bottle.
Check the coolant freeze point in the radiator
and in the coolant expansion bottle. If engine
coolant needs to be added, the contents of the
coolant expansion bottle must also be protected
against freezing.
If frequent engine coolant additions are
required, the cooling system should be pressure
tested for leaks.
Maintain engine coolant concentration at a
minimum of 50% OAT coolant (conforming to
MS.90032) and distilled water for proper corro
-
sion protection of your engine which contains
aluminum components.
Make sure that the coolant expansion bottle
overflow hoses are not kinked or obstructed.
Keep the front of the radiator clean. If your
vehicle is equipped with air conditioning, keep
the front of the condenser clean.
Do not change the thermostat for Summer or
Winter operation. If replacement is ever neces -
sary, install ONLY the correct type thermostat.
Other designs may result in unsatisfactory
engine cooling performance, poor gas mileage,
and increased emissions.
BRAKE SYSTEM
In order to ensure brake system performance, all
brake system components should be inspected
periodically Ú page 210.
Fluid Level Check — Brake Master Cylinder
Check the fluid level in the master cylinder
immediately if the Brake System Warning Light
indicates system failure.
Check the fluid level in the master cylinder when
performing underhood services.
Clean the top of the master cylinder area before
removing the cap. Add fluid to bring the level up to
the top of the “FULL” mark on the side of the
master cylinder reservoir.
Overfilling of fluid is not recommended because it
may cause leaking in the system.
Add enough fluid to bring the level up to the
requirements described on the brake fluid
WARNING!
Riding the brakes can lead to brake failure and
possibly a collision. Driving with your foot resting
or riding on the brake pedal can result in
abnormally high brake temperatures, excessive
lining wear, and possible brake damage. You
would not have your full braking capacity in an
emergency.

22_LX_OM_EN_USC_t.book Page 226

275
B
Back-Up
......................................................... 116Battery.................................................... 78, 216Charging System Light................................. 78Keyless Key Fob Replacement.................... 13Location.................................................... 216Belts, Seat..................................................... 189Body Mechanism Lubrication........................ 221B-Pillar Location............................................. 247Brake Assist System...................................... 146Brake Control System.................................... 146Brake Fluid.......................................... 226, 269Brake System...................................... 226, 263Fluid Check..................................... 226, 269Master Cylinder......................................... 226Parking........................................................ 90Warning Light..................................... 77, 263Brake/Transmission Interlock......................... 92Break-In Recommendations, New Vehicle....... 89Brightness, Interior Lights................................ 49Bulb Replacement......................................... 238Bulbs, Light.......................................... 191, 238
C
Camera, Rear................................................ 116Capacities, Fluid............................................ 267Caps, Filler Oil (Engine)................................................ 214Radiator (Coolant Pressure)...................... 225
Car Washes................................................... 260Carbon Monoxide Warning................... 191, 192CargoVehicle Loading........................................ 119Cargo Area Cover............................................. 67Cargo Compartment........................................ 67Cellular Phone.............................................. 144Certification Label......................................... 119Chains, Tire................................................... 257Chart, Tire Sizing........................................... 243Check Engine Light
(Malfunction Indicator Light)............................ 85Checking Your Vehicle For Safety................. 189Checks, Safety.............................................. 189Child Restraint.............................................. 176Child RestraintsBooster Seats........................................... 179Child Seat Installation.............................. 187How To Stow An unused ALR Seat Belt.... 184Infant And Child Restraints....................... 178Lower Anchors And Tethers For Children.. 181Older Children And Child Restraints......... 178Seating Positions...................................... 180Child Safety Locks........................................... 25Clean Air Gasoline......................................... 265CleaningWheels..................................................... 256Climate Control................................................ 52Automatic.................................................... 52Coin Holder...................................................... 57
Cold Weather Operation...................................89Compact Spare Tire...................................... 254ConsoleFloor............................................................57Contract, Service........................................... 271Cooling Pressure Cap (Radiator Cap)............ 225Cooling System............................................. 224Adding Coolant (Antifreeze)...................... 225Coolant Capacity....................................... 267Coolant Level................................... 224, 226Disposal Of Used Coolant......................... 225Drain, Flush, And Refill............................. 224Inspection................................................. 226Points To Remember................................ 226Pressure Cap............................................ 225Radiator Cap............................................. 225Selection Of Coolant (Antifreeze)......................... 224, 267, 268Corrosion Protection..................................... 260Cruise Control (Speed Control)............... 98, 100Cruise Light............................................... 82, 83Customer Assistance.................................... 270Cybersecurity................................................ 128
D
Daytime Running Lights...................................45Dealer Service............................................... 217Deck LidPower Release.............................................65Defroster, Windshield................................... 190
11

22_LX_OM_EN_USC_t.book Page 275

279
Modifications/Alterations Vehicle
.......................................................... 8Monitor, Tire Pressure System....................... 157Mopar Parts................................................... 272MP3 Control.................................................... 58Multi-Function Control Lever............................ 45
N
New Vehicle Break-In Period............................ 89
O
Occupant Restraints...................................... 160Octane Rating, Gasoline (Fuel)............ 264, 268Oil Change Indicator........................................ 72Reset........................................................... 72Oil Filter, Change........................................... 218Oil Filter, Selection......................................... 218Oil Pressure Light............................................ 79Oil, Engine........................................... 217, 268Capacity.................................................... 267Checking................................................... 216Dipstick..................................................... 216Disposal.................................................... 218Filter................................................ 218, 268Filter Disposal........................................... 218Identification Logo..................................... 218Materials Added To................................... 218Pressure Warning Light............................... 79
Recommendation............................ 217, 267Synthetic.................................................. 218Viscosity................................................... 267Onboard Diagnostic System............................. 84Operating Precautions..................................... 84Operator ManualOwner's Manual........................................ 273Outside Rearview Mirrors................................ 38Overheating, Engine...................................... 204
P
Paddle Shift Mode........................................... 96Paddle Shifters................................................ 96Paint Care..................................................... 260Parking Brake.................................................. 90ParkSense System, Rear.............................. 108Passive Entry................................................... 23Pets.............................................................. 189Placard, Tire And Loading Information.......... 247PowerBrakes...................................................... 263Deck Lid Release......................................... 65Distribution Center (Fuses)....................... 234Door Locks.................................................. 22Mirrors......................................................... 38Outlet (Auxiliary Electrical Outlet)................ 60
Seats...........................................................31Steering.......................................................97Sunroof........................................................63Tilt/Telescoping Steering Column................26Windows......................................................61Power SeatsForward.......................................................32Lumbar........................................................32Rearward.....................................................32Recline.........................................................32Pregnant Women And Seat Belts.................. 165Preparation For Jacking................................ 197PretensionersSeat Belts................................................. 166
R
Radial Ply Tires.............................................. 251Radiator Cap (Coolant Pressure Cap)............ 225Radio Operation............................................ 144Rain Sensitive Wiper System...........................51Rear Axle (Differential).................................. 228Rear Camera................................................. 116Rear Cross Path............................................ 154Rear ParkSense System................................ 108Rear Seats, Folding..........................................30Rear Wheel Drive (RWD)Towing...................................................... 20911

22_LX_OM_EN_USC_t.book Page 279