2022 ACURA NSX warning

80
uuIndicators u
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
Gear Position
Indicator•Indicates the current gear selection.
2 Shifting P. 324—
Transmission
System Indicator
•The indicated current gear selection
blinks if there is a problem with the
transmission system.• Avoid sudden start and acceleration, and
stop in a safe place immediately.
Have your vehicle checked by an
authorized Acura NSX dealer.
•All the gear positions may light for
several seconds, and go off.• When all the gear positions light,
immediately stop your vehicle in a safe
place.
• Indicators go off if there is no problem.
However, even if they go off, take your
vehicle to an authorized Acura NSX dealer
for inspection.
—
•The indicated current gear selection
or all the gear positions blink if
there is a problem with the
transmission system.• Immediately stop in a safe place.2 Emergency Towing P. 465
•Have your vehicle checked by an
authorized Acura NSX dealer.
•The indicated current gear selection
or all the gear positions blink if you
cannot select
(P due to the
transmission system failure.
• The power system can be activated as a
temporary measure.
2 If the Transmission System Indicator
Blinks along with the Warning
Message P. 458
•Set the parking brake when parking.
• Have your vehicle checked by an
authorized Acura NSX dealer immediately.
22 ACURA NSX PMC-31T6N6500.book 80 ページ ２０２１年９月２８日　火曜日　午後４時７分

84
uuIndicators u
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
Low Tire Pressure/
TPMS Indicator
•Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Comes on if the tire pressure of any
of the tires becomes significantly
low.
• Blinks for about one minute, and
then stays on if there is a problem
with the TPMS.•Comes on while driving - Stop in a safe
place, check tire pres sures, and inflate the
tire(s) if necessary.
• Blinks and remains on - Have your
vehicle checked by an authorized Acura
NSX dealer.
System Message
Indicator
• Comes on for a few seconds when
you set the power mode to ON,
then goes off.
• Comes on along with a beep when
a problem is detected. A system
message on the driver information
interface appears at the same time.•While the indicator is on, roll the right
selector wheel to see the message again.
• Refer to the Indicators information in this
chapter when a system message appears
on the driver information interface. Take
the appropriate action for the message.
• The driver information interface does not
return to the normal screen unless the
warning is canceled, or the right selector
wheel is rolled.
—
22 ACURA NSX PMC-31T6N6500.book 84 ページ ２０２１年９月２８日　火曜日　午後４時７分

85
uuIndicators u
Continued
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
Turn Signal and
Hazard Warning
Indicators•Blinks when you operate the turn
signal lever.
• Blink if you press the hazard
warning button.•Does not blink or blinks rapidly - Have
your vehicle checked by an authorized
Acura NSX dealer.
2 Replacing Light Bulbs P. 401, 402
—
High Beam
Indicator•Comes on when the high beam
headlights are on.——
Lights On Indicator
•Comes on whenever the light
switch is on, or in AUTO when
the exterior lights are on.• If you set the power mode to VEHICLE OFF
while the exterior lights are on, a chime
sounds when the driver’s door is opened.
—
Immobilizer
System Indicator
•Comes on briefly when you set
the power mode to ON, then
goes off.
• Comes on if the immobilizer
system cannot recognize the key
information.•Blinks - You cannot start the power
system. Set the power mode to VEHICLE
OFF, then select the ON mode again.
• Repeatedly blinks - The system may be
malfunctioning. Have your vehicle checked
by an authorized Acura NSX dealer.
• Do not attempt to alter this system or add
other devices to it. Electrical problems can
occur.
—
22 ACURA NSX PMC-31T6N6500.book 85 ページ ２０２１年９月２８日　火曜日　午後４時７分

87
uuIndicators uDriver Information Interface Wa rning and Information Messages
Continued
Instrument Panel
Driver Information Interface Warning and Information Messages
The following messages appear only on the driver information interface. Roll the right selector wheel to see the message again with the
system message indicator on.
MessageConditionExplanation
• Appears when the washer fluid is low.•Refill the washer fluid.
2 Refilling Window Washer Fluid P. 400
•Appears when the scheduled maintenance is due soon.
• Consequently, Service Due Now and Service Past
Due follow.2Maintenance Minder Messages on the Driver
Information Interface P. 381
•Appears when the temperatur e of the transmission is
starting to get too hot.
• The performance of the vehicle may be reduced.•It may not be possible to use the paddle shifters.
• Until the message disappears, reduce your speed and
allow the system to cool down.
•Appears when the transmission system temperature is
too high. The vehicle does not operate properly.•You may find it difficult to accelerate, or to start the
vehicle on uphill.
• Immediately stop in a safe place in
(P.
• Let the engine idle until the message disappears.
22 ACURA NSX PMC-31T6N6500.book 87 ページ ２０２１年９月２８日　火曜日　午後４時７分

94
uuIndicators uDriver Information Interface Wa rning and Information Messages
Instrument Panel
MessageConditionExplanation
•Appears when the transmission temperature is too low
to operate (approx. -13°F [-25°C] or below).• You can start the engine an d use the climate control
system to warm up the interior, which will also warm
the transmission enough for you to drive the vehicle.
• The engine speed does not increase even if you fully
depress the accelerator pedal.
•Appears when the High Volt age battery temperature is
extremely low (-4°F [-20°C]).• Contact an authorized Acura NSX dealer immediately.
• To prevent the message to come on, store the vehicle in
the garage or drive in advance to warm up the High
Voltage battery.
• The minimum operation guarantee environmental
temperature is -4°F [-20°C].
•Appears when the twin motor unit fluid temperature is
extremely low.•Vehicle speed is limited to 81 mph (130 km/h) until twin
motor unit fluid warms up.
• Appears if the AWD system has a problem due to a
hybrid system or power distribution control failure.•Drives with the rear wheels only in this state.
Have your vehicle checked by an authorized Acura NSX
dealer.
•Appears when the engine is running and indicates that
the engine oil level is low.• Appears while driving - Immediately stop in a safe
place.
2 If the Check Engine Oil Level Warning Appears
P. 459
22 ACURA NSX PMC-31T6N6500.book 94 ページ ２０２１年９月２８日　火曜日　午後４時７分

102
uuGauges and Displays uDriver Information Interface
Instrument Panel
Driver Information Interface
The driver information interface shows in formation such as the estimated travelable
distance and fuel economy of the vehicle. It also displays messages such as warnings
and other helpful information.
Roll the right selector wheel to change the display.
■Switching the Display
Right Selector Wheel Engine Oil LifeElapsed Time
Blank Screen
Average Speed
Range
Average Fuel Economy/
Instant Fuel Economy
Tire Pressure for
Each Tire
Turn-by-Turn
Directions
Oil Level Check Assist Compass
22 ACURA NSX PMC-31T6N6500.book 102 ページ ２０２１年９月２８日　火曜日　午後４時７分

128
Controls
Opening and Closing the Windows
Opening/Closing the Power Windows
The power windows can be opened and closed when the power mode is in ON,
using the switches on the doors. The driver’s side switches can be used to open and
close both windows.
The power window lock button on the driver’s side must be switched off (not
pushed in, indicator off) to open and close the passenger’s window from the
passenger’s side.
When the power window lock button is pu shed in, the indicator comes on and you
can only operate the driver’s window. Turn the power window lock button on if a
child is in the vehicle.
■Automatic operation
To open: Push the switch down firmly.
To close: Pull the switch up firmly.
The window opens or cl oses completely. To
stop the window at any time, push or pull the
switch briefly.
■Manual operation
To open: Push the switch down lightly, and
hold it until the desired position is reached.
To close: Pull the switch up lightly, and hold it
until the desired position is reached.
■Opening/Closing the Windows with Auto-Open/Close Function
1 Opening/Closing the Power Windows
The power windows can be operated for up to 10
minutes after you set the power mode to VEHICLE
OFF.
Opening either door cancels this function.
Auto Reverse
If a power window senses resistance when closing
automatically, it stops clos ing and reverses direction.
The driver’s window auto re verse function is disabled
when you continuously pull up the switch.
The auto reverse function stops sensing when the
window is almost closed to en sure that it fully closes.
3WARNING
Closing a power window on someone’s
hands or fingers can cause serious injury.
Make sure your passenger is away from the
windows before closing them.
ON
OFF
Power Window
Lock Button
IndicatorDriver’s
Window
SwitchPassenger’s
Window Switch
22 ACURA NSX PMC-31T6N6500.book 128 ページ ２０２１年９月２８日　火曜日　午後４時７分

131
uuOperating the Switches Around the Steering Wheel uENGINE START/STOP Button
Continued
Controls
If you leave the vehicle for more than 30 minutes with the transmission in (P and
the power mode in ACCESSORY, the vehicl e will automatically go into VEHICLE OFF
(LOCK) mode to prevent draining the 12-volt battery.
If you open the driver’s door when the pow er mode is set to ACCESSORY, a warning
buzzer will sound.
■Automatic Power Off
■Power Mode Reminder
22 ACURA NSX PMC-31T6N6500.book 131 ページ ２０２１年９月２８日　火曜日　午後４時７分