2021 YAMAHA YFZ450R check engine

9-24
9
8. Wash the sponge material gently but thor-
oughly in solvent. WARNING! Always use
parts cleaning solvent. Never use low-
flash-point solvents or gasoline because
the engine could catch fire or explode.
[EWB01943]
9. Squeeze the excess solvent out of the sponge material and let it dry. NOTICE: Do
not twist the sponge material when
squeezing it.
[ECB00442]
10. Check the sponge material and replace it if damaged.
11. Apply Yamaha foam air filter oil or other qual- ity foam air filter oil to the sponge material.TIPThe sponge material should be wet but not drip-
ping. 12. Pull the sponge material over the air filter ele-ment frame.
13. Apply all-purpose grease to the air filter ele- ment seat.
1. Sponge material
2. Air filter element frame
1
2
UBKD60E0.book Page 24 Wednesday, November 18, 2020 8:39 AM

9-26
9
17. Install the seat.
TIPThe air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated
more often if the ATV is operated in extremely
dusty areas. Each time the air filter element main-
tenance is performed, check the air inlet of the air
filter case for obstructions. Check the air filter
case rubber joint to the throttle body and the rub-
ber joint manifold fittings for an air-tight seal.
Tighten all fittings securely to avoid the possibility
of unfiltered air entering the engine. EBU30863Cleaning the spark arresterSelect a well-ventilated area free of combustible
materials and make sure the exhaust and muffler
are cool.
WARNING
EWB02342Always let the exhaust system cool prior to
touching exhaust components.
Do not start the engine with the spark arrester
removed. Sparks or exhaust particulate can
cause eye injury, burns, or start a fire.
1. Remove the tailpipe cover by removing the
bolts.
2. Remove the retainer by removing the bolts, and then remove the tailpipe and gasket from
the muffler.1. Tailpipe cover
2. Bolt2
1 2
UBKD60E0.book Page 26 Wednesday, November 18, 2020 8:39 AM

9-28
9
EBU29705Adjusting the throttle lever free playPeriodically check the throttle lever free play and
adjust if necessary.1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle lever free play, turn
the throttle lever free play adjusting bolt in di-
rection (a). To decrease the throttle lever free
play, turn the adjusting bolt in direction (b).
4. Tighten the locknut.
5. Slide the rubber cover to its original position.
EBU24062Valve clearanceThe valve clearance changes with use, resulting in
improper air-fuel mixture and/or engine noise. To
prevent this from occurring, the valve clearance
must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance chart.EBU29602BrakesReplacement of brake components requires pro-
fessional knowledge. Brake service should be
performed by a Yamaha dealer.
Tightening torque:
Tailpipe cover bolt:8 N·m (0.8 kgf·m, 5.9 lb·ft)
1. Rubber cover
2. Throttle lever free play adjusting bolt
3. Locknut
4. Throttle lever free playThrottle lever free play: 2.0–4.0 mm (0.08–0.16 in)
32
4
(a)(b)
1
UBKD60E0.book Page 28 Wednesday, November 18, 2020 8:39 AM

9-38
9
EBU24886Lubricating the drive chainThe drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
chart, otherwise it will quickly wear out, especially
when riding in dusty or wet areas. Service the
drive chain as follows.NOTICEECB00562The drive chain must be lubricated after wash-
ing the ATV or riding in the rain or wet areas.
1. Clean the drive chain with a drive chain clean-er and a small soft brush. NOTICE: To pre-
vent damaging the O-rings, do not clean
the drive chain with steam cleaners, high-
pressure washers or inappropriate sol-
vents.
[ECB00572]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain lubricant. NOTICE: Do
not use engine oil or any other lubricants
for the drive chain, as they may contain
substances that could damage the O-
rings.
[ECB00582]
EBU24905
Checking and lubricating the cablesThe operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.
1. O-rings
1
1
Recommended lubricant:
Yamaha cable lubricant or other suitable cable lubricant
UBKD60E0.book Page 38 Wednesday, November 18, 2020 8:39 AM

9-52
9
EBU27696Troubleshooting chartsStarting problems or poor engine performance
Check the fuel level in
the fuel tank.1. Fuel
There is enough fuel.There is no fuel.
Check the battery.
Supply fuel.
The engine does not start.
Check the battery.
Operate the electric starter.4. Compression
There is compression.
There is no compression.
The engine does not start.
Have a Yamaha dealer check the ATV.
Remove the spark plug
and check the electrodes.3. Ignition
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug. Have a Yamaha dealer check the ATV.
The engine does not start.
Check the compression.
DryWet
Operate the electric starter.
Have a Yamaha dealer check the ATV.
The engine does not start.
Check the ignition.
Operate the electric starter.2. Battery
The engine turns over
quickly.
The engine turns over
slowly.
The battery is good.Check the battery lead connections,
and have a Yamaha dealer charge
the battery if necessary.
UBKD60E0.book Page 52 Wednesday, November 18, 2020 8:39 AM

9-53
9Engine overheating
WARNING
EWB02291Wait for the engine and radiator to cool before removing the radiator cap. You could be burned by
hot fluid and steam blown out under pressure. Always put a thick rag over the cap when opening.
Allow any remaining pressure to escape before completely removing the cap. TIP
Tap water can be used in an emergency. Change to the recommended coolant as soon as possible.
 The engine will tend to overheat if the radiator is caked with mud, or if the ATV is overloaded. Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer check
and repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
There is
leakage.
There is
no leakage.
UBKD60E0.book Page 53 Wednesday, November 18, 2020 8:39 AM

12-1
12
INDEX
AAccessories and loading ................................................ 7-5
Air filter element, cleaning ........................................... 9-22BBattery ......................................................................... 9-43
Brake and clutch levers, checking and lubricating ...... 9-39
Brake fluid, changing ................................................... 9-31
Brake fluid level, checking ........................................... 9-30
Brake lever ..................................................................... 5-5
Brake lever free play, checking the front ..................... 9-32
Brake light switches ..................................................... 9-34
Brake pads, checking the front and rear ..................... 9-29
Brake pedal .................................................................... 5-6
Brake pedal, checking and lubricating ........................ 9-40
Brake pedal height, checking ...................................... 9-32
Brakes .......................................................................... 9-28
Brakes, front and rear .................................................... 6-4
Brake/tail light .............................................................. 9-49CCables, checking and lubricating ................................ 9-38
Chassis fasteners .......................................................... 6-7
Cleaning ....................................................................... 10-1
Clutch lever .................................................................... 5-5
Clutch lever free play, adjusting .................................. 9-35
Coolant .................................................................6-4, 9-20
Coolant, changing ........................................................ 9-22
Coolant temperature warning light ................................ 5-2
Cowling and panels, removing and installing .............. 9-10
DDrive chain ..................................................................... 6-5
Drive chain, lubricating ................................................ 9-38
Drive chain slack .......................................................... 9-36EEngine break-in .............................................................. 7-4
Engine oil ....................................................................... 6-4
Engine oil and oil filter element .................................... 9-14
Engine, start ................................................................... 7-1
Engine stop switch ........................................................ 5-3
Engine trouble warning light .......................................... 5-2FFuel ......................................................................... 5-9, 6-4
Fuel level warning light .................................................. 5-2
Fuel tank cap ................................................................. 5-8
Fuse, replacing ............................................................ 9-46HHandlebar position, adjusting ...................................... 5-23
Handlebar switches ....................................................... 5-3
Headlight beam, adjusting ........................................... 9-49
Headlight bulb, replacing ............................................. 9-46IIdentification numbers ................................................... 1-1
Indicator light and warning lights ................................... 5-1
Instruments, lights and switches ................................... 6-7LLabel locations ............................................................... 2-1
Light switch ................................................................... 5-3
UBKD60E0.book Page 1 Wednesday, November 18, 2020 8:39 AM