2021 YAMAHA TMAX clock

Instrument and control functions
5-5
5
EAU77141
TachometerThe tachometer shows the engine
speed in crankshaft revolutions per
minute (r/min).
When the vehicle power is turned on,
the tachometer needle will sweep
across the r/min range and return to
zero in order to test the electrical cir-
cuit.NOTICE
ECA23050
Do not operate the en gine in the ta-
chometer hi gh-r/min zone.
Hi gh-r/min zone: 8250 r/min and
a b ove
EAU91510
Multi-function d isplay
WARNING
EWA12313
Be sure to stop the vehicle before
makin g any settin g chan ges to the
multi-function display. Chan gin g
settin gs while ri din g can distract the
operator an d increase the risk of an
acci dent.TIPCertain multi-function display items
can be adjusted via the setting mode.
(See page 5-11.)
1. Tachometer
2. High-r/min zone
1 1
2 2
1. Information display
2. Function select icon
3. Fuel meter
4. Clock
5. Grip warmer/Seat heater icons
6. Drive mode display
7. Coolant temperature meter
1 2 3 4 5
6
7
1. Oil change indicator “Oil”
2. V-belt replacement indicator “V-Belt”
3. Eco indicator “ECO”
1 2
3
UB3TE1E0.book Page 5 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-11
5
NOTICE
ECA15474
If there is a malfunction, “– –.–” will
b e continuously displaye d. Have a
Yamaha dealer check the vehicle.Setting mode
Stop the vehicle and then push the
“MENU” switch for 2 seconds to enter
the setting mode. To exit the setting
mode and return to the standard dis-
play mode, push the “MENU” switch
again for 2 seconds or
select “ ”.TIPWhen the malfunction indicator light is
on, setting mode cannot be entered.
Menu items
Grip warmer settings1. Use the select switch to highlight “Grip Warmer”.
2. Push the “MENU” switch. The grip warmer setting display will be
shown.
1. Setting mode display
1
Cate gory Description
This function allows you to
set the low, middle, and
high settings to 10 tem-
perature levels.
This function allows you to
set the low, middle, and
high settings to 10 tem-
perature levels.
This function allows you to
turn the traction control
system on or off.
This function allows you to
check and reset the oil
change interval (indicator),
V-Belt change interval (in-
dicator), and the “FREE”
maintenance interval.
This function allows you to
switch the fuel consump-
tion units between
“L/100km” and “km/L”.
For UK-spec vehicles: this
function is not available.
This function allows you to
change the items shown in
3 information displays.
This function allows you to
adjust the brightness of
the instrument panel.
This function allows you to
set the clock.Grip WarmerSeat HeaterTraction ControlMaintenance
UnitDisplayBrightnessClock
This function allows you to
reset all items to their fac-
tory preset or default set-
tings; excepting the
odometer, clock, and
maintenance counter
items “Oil” and “V-Belt”.
All Reset
UB3TE1E0.book Page 11 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-16
5
4. Push the “MENU” switch to return
to the menu screen.
Setting the clock
TIPThe clock uses a 12-hour time system.1. Use the select switch to highlight 2.
3. When the hour digits are highlight-
ed, use the select switch to set the
hours.
4. minute digits are highlighted.
5. Use the select switch to set the minutes. 6.
to the menu screen.
Resetting all of the display items
1. Use the select switch to highlight
2.
3. Use the select switch to highlight
switch. All items are reset to facto-
ry preset or default settings.
UB3TE1E0.book Page 16 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-17
5
TIPThe odometer, clock, maintenance
counter item “Oil” and maintenance
counter item “V-Belt” will not be reset.To exit the setting mode1. Use the select switch to highlight
“Return”. 2. Push the “MENU” switch to exit
the setting mode and return to the
standard display mode.
EAU44916
Front brake leverThe front brake lever is located on the
right side of the handlebar. To apply
the front brake, pull this lever toward
the throttle grip.
The front brake lever is equipped with
a brake lever position adjusting dial. To
adjust the distance between the front
brake lever and the throttle grip, push
the brake lever away from the throttle
grip and rotate the adjusting dial. Make
sure the setting number on the adjust-
ing dial aligns with the match mark on
the brake lever.1. Front brake lever
2. Distance
3. Match mark
4. Brake lever position adjusting dial
1
3
4
2
UB3TE1E0.book Page 17 Friday, September 11, 2020 8:48 AM

Instrument and control functions
5-20
5
EAU77324
Fuel tank capTo access the fuel tank, open the fuel
tank cap lid. (See page 3-11.)
To remove the fuel tank cap, press the
lock release button and turn the fuel
tank cap counterclockwise. To install the fuel tank cap, turn it
clockwise until the lock release button
pops out.
WARNING
EWA11263
Make sure that the fuel tank cap is
properly installe
d an d locked in
place before operatin g the vehicle.
Leakin g fuel is a fire hazar d.
EAU13222
FuelMake sure there is sufficient gasoline in
the tank.
WARNING
EWA10882
Gasoline an d gasoline vapors are
extremely flammab le. To avoid fires
an d explosions an d to re duce the
risk of injury when refuelin g, follow
these instructions.1. Before refueling, turn off the en- gine and be sure that no one is sit-
ting on the vehicle. Never refuel
while smoking, or while in the vi-
cinity of sparks, open flames, or
other sources of ignition such as
the pilot lights of water heaters
and clothes dryers.
2. Do not overfill the fuel tank. When refueling, be sure to insert the
pump nozzle into the fuel tank filler
hole. Stop filling when the fuel
reaches the bottom of the filler
tube. Because fuel expands when
it heats up, heat from the engine or
the sun can cause fuel to spill out
of the fuel tank.
1. Fuel tank cap lid
1. Lock release button
2. Fuel tank cap
1
1 2
UB3TE1E0.book Page 20 Friday, September 11, 2020 8:48 AM

Periodic maintenance an d a djustment
8-38
8
EAU86420
En gine overheatin g
WARNING
EWAT1041
Do not remove the ra diator cap when the en gine an d ra diator are hot. Scal din g hot flui d an d steam may be
b lown out un der pressure, which coul d cause serious injury. Be sure to wait until the en gine has coole d.
 Place a thick rag , like a towel, over the ra diator cap, an d then slowly rotate the cap counterclockwise to the
d etent to allow any resi dual pressure to escape. When the hissin g soun d has stopped , press down on the cap
while turnin g it counterclockwise, an d then remove the cap.TIPIf coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended cool-
ant as soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See TIP.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
UB3TE1E0.book Page 38 Friday, September 11, 2020 8:48 AM

Periodic maintenance an d a djustment
8-39
8
EAU77373
Emer gency mo deWhen the smart key is lost, damaged,
or its battery has discharged, the vehi-
cle can still be turned on and the en-
gine started. You will need a
mechanical key and the smart key sys-
tem identification number. To operate
the vehicle in emergency mode, carry
out the following steps.TIPEmergency mode operation will be
cancelled if the respective steps are
not carried out within the time set for

switch is pushed.1. Stop the vehicle in a safe place.
2. Unlock the seat by inserting the
mechanical key into the lock lo-
cated right side of body and turn it
counter clockwise. 3. Open the seat and check that the
trunk light comes on.
4. Ž switch once.
5. Without completely shutting the seat, raise and lower it three times
within 10 seconds.
TIPUse the rear storage compartment
light as a guide when raising and low-
ering the seat.
The smart key system indicator
light on the speedometer will
come on for three seconds to indi-
cate the transition to emergency
mode. 6. After the smart key system indica-
tor light goes off, use the / Ž
switch to enter the identification
number.
1. Smart key system indicator light Ž
1. Identification number
1 1
123456
1
UB3TE1E0.book Page 39 Friday, September 11, 2020 8:48 AM