2021 VOLKSWAGEN UP! check engine

Changing bulbs in the side turn signals
Fig. 169 Removing the side turn signal bulb
Fig. 170 Side turn signal: changing the bulb
First read and observe the introductoryinformation and safety warnings⇒
Introduction
The actions should only be carried out in the specified order:
1.Observe and follow the instructions on the checklist ⇒ Information on changing bulbs.
2.With one hand, push the side turn signal to the front ⇒ Fig. 169①.
3.Manually lever the side turn signal out of the vehicle body ②.
4.Pull the bulb and bulb holder out in the direction of the arrow ⇒ Fig. 170①.
5.Pull the bulb straight out of the bulb holder.
6.Replace the defective bulb with a new bulb of the same type.
7.Replace the bulb holder.
8.Insert the side turn signal into the body, with the side facing the rear of the vehicle first.
Push it in until the spring on the other side of the side turn signal engages.
Starting the engine with jump leads
 Introduction
This chapter contains information on the followingsubjects:
⇒ How to start the engine using jump leads
If the engine fails to start because the vehicle battery is flat, the flat battery can be connected to the
battery of another vehicle to start the engine. Before using jump leads, check the window on the
vehicle battery ⇒ Vehicle battery.
Jump leads must comply with DIN 72553 (see manufacturer's documentation). On petrol engine
vehicles, the conductor must have a cross-section of at least 25 mm.
Additional information and warnings:
•Pull-away assist systems ⇒ Pull-away assist systems
•Preparation for working in the engine compartment ⇒ Preparation for working in the engine
compartment
•Battery ⇒ Vehicle battery
Before inserting the screwdriver, slide a piece of paper (or similar) in between the screwdriver
and the bumper in order to prevent any damage to the paintwork on the bumper.
NOTICE
2

The discharged vehicle battery must be properly connected to the vehicle's electrical system.
The vehicles must not touch. Otherwise electricity could flow as soon as the positive terminals are
connected.
Ensure that the battery clamps have good metal-to-metal contact with the battery terminals.
If the engine does not start immediately, switch off the starter after about 10 seconds and try again
after about half a minute.
The steps should only be carried out in the specified order.
Attaching the jump leads
•Switch off the ignition in both vehicles ⇒ Starting and stopping the engine.
•If necessary, open the battery cover in the engine compartment ⇒ Vehicle battery.
•Connect one end of the red jump lead to the positive terminal ⇒ Fig. 171⊕ or ⇒ Fig. 172⊕ in
the vehicle with the discharged battery Ⓐ ⇒.
•Connect the other end of the red jump lead to the positive terminal ⊕ in the vehicle providing
assistance Ⓑ.
•In vehicles without start/stop system: connect one end of the black jump lead to the negative
terminal ㊀ in the vehicle providing assistance Ⓑ ⇒ Fig. 171.
•In vehicles with start/stop system: connect one end of the black jump lead Ⓧ to a suitable
earth connection, to a solid metal part that is securely bolted onto the cylinder or to the cylinder
block itself ⇒ Fig. 172.
•Connect the other end of the black jump lead Ⓧ to a solid metal component bolted on to the
engine block, or onto the engine block in the vehicle with the discharged battery. Do not
connect it to a point near the battery Ⓐ ⇒.
•Position the leads in such a way that they cannot come into contact with any moving parts in the
engine compartment.
Starting the engine
•Start the engine of the vehicle providing assistance and let it run at idle.
•Start the engine of the car with the discharged vehicle battery and wait two or three minutes
until the engine is running smoothly.
Removing the jump leads
•Before disconnecting the jump leads, switch off the dipped beam headlights if they are switched
on.
•Turn on the heater blower and rear window heater in the vehicle battery with the discharged
battery. This helps minimise the voltage peaks generated when the leads are disconnected.
•With the engines running, disconnect the jump leads in the exact reverse order to the
instructions given above.
•Close the battery cover.
Tow-starting and towing
 Introduction
This chapter contains information on the followingsubjects:
⇒  Notes on tow-starting
⇒ Notes on towing
Jump starting the vehicle incorrectly can cause the battery to explode, which can lead to
serious injuries. Please note the following in order to reduce the risk of the battery exploding:
•All work on the vehicle battery and the electrical system can cause serious chemical
burns, fire and electric shocks. Always read the warnings and safety information before
carrying out any kind of work on the vehicle battery ⇒ Vehicle battery.
•Always wear suitable eye protection and never lean over the vehicle battery.
•Attach the connector cables in the correct order – the positive cable first, followed by the
negative.
•Never connect the negative cable to parts of the fuel system or to the brake lines.
•The non-insulated parts of the battery clamps must not be allowed to touch. The jump lead
attached to the positive vehicle battery terminal must not touch metal parts of the vehicle.
•Check the window on the vehicle battery using a torch if necessary. If the display is light
yellow or colourless, do not jump start the vehicle. Seek expert assistance.
•Avoid electrostatic discharge in the vicinity of the vehicle battery. The gas emitted from the
vehicle battery could be ignited by sparks.
•Do not use jump leads to start the engine if the vehicle battery is damaged or if it is or has
ever been frozen.
WARNING

•Switch on the ignition and the hazard warning lights.
•Once both vehicles are in motion, release the clutch.
•As soon as the engine starts, press the clutch and put the gear into neutral. This helps to
prevent driving into the towing vehicle.
However, if the vehicle still has to be tow-started (automated manual
gearbox):
•Switch on the ignition and the hazard warning lights.
•Place the selector lever in position N.
•When both vehicles are in motion and the brake pedal indicator lamp goes out, move the
selector lever to position D.
•As soon as the engine starts, press the brake pedal and move the selector lever to position N.
This helps to prevent driving into the towing vehicle.
Notes on towing
First read and observe the introductoryinformation and safety warnings⇒
Introduction
Tow rope or tow bar
It is easier and safer to tow a vehicle with a tow bar. Only use a tow rope if you do not have a tow
bar.
The tow rope should be slightly elastic to reduce the strain on both vehicles. It is advisable to use a
tow rope made of synthetic fibre or similarly elastic material.
Only attach the tow rope or tow bar to the specially provided towing eyes or to the towing bracket.
When a vehicle with a manual gearbox has to be towed:
Check whether the vehicle can be towed ⇒ When should your vehicle not be towed?.
•Move the gear stick to neutral ⇒ Changing gear.
•Do not allow the vehicle to be towed at speeds faster than 50 km/h (30 mph).
•Do not have the vehicle towed further than 50 km (30 miles).
When a vehicle with an automated manual gearbox has to be towed:
Check whether the vehicle can be towed ⇒ When should your vehicle not be towed?
•Switch on the ignition.
•Move the selector lever to N⇒ Changing gear.
•Check whether the automated manual gearbox is really in neutral. To do this drive the car a few
metres as a test. The automated manual gearbox is in neutral if the vehicle can be easily
moved.
•Seek expert assistance if the automated manual gearbox cannot be put into neutral ⇒.
•Do not allow the vehicle to be towed at speeds faster than 50 km/h (30 mph).
•Do not have the vehicle towed further than 50 km (30 miles).
•If a breakdown truck is used, the vehicle must be towed with the front wheels raised.
When should your vehicle not be towed?
•If, due to damage, the vehicle gearbox no longer contains any lubricant.
•If the automated manual gearbox cannot be put into neutral ⇒.
•If the distance to be towed is further than 50 km - applies to vehicles with an automated manual
gearbox only.
•If the steering function or the operating clearance of the wheels cannot be ensured, e.g. after an
accident.
The vehicle can only be towed when the handbrake and steering lock are not engaged.
Fitting the front towing eye
When tow-starting, unburnt fuel can enter the catalytic converter and damage it.
NOTICE
Never tow a vehicle with automated manual gearbox if the automated manual gearbox cannot
be put into neutral. Otherwise, the gearbox and engine can suffer considerable damage.
NOTICE