2021 VOLKSWAGEN T-ROC wheel

Fig. 203 Changing a wheel: loosening the wheel bolts.

Fig. 204 Changing a wheel: tyre valve ① and locations of the anti-theft wheel bolt ② or ③.
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Use a suitable box spanner to loosen the wheel bolts.
Slacken the wheel bolts only by approximately one turn before raising the vehicle with the vehicle
jack.
If a wheel bolt is very tight, you may be able to loosen it by pushing down the end of the spanner
carefully with your foot. Hold on to the car for support and take care not to slip.
Loosening the wheel bolts
it will go ⇒ Fig. 203 .
-clockwise ⇒ .
Loosening the anti-theft wheel bolt
-theft wheel bolt out of the vehicle toolkit.
anti-theft wheel bolt as far as it will go.

-clockwise ⇒ .
Screwing in the anti-theft wheel bolt (wheel cover)

On wheels with a wheel cover, the anti-theft wheel bolt must be screwed into position
⇒ Fig. 204②  or ③ according to the position of the tyre valve ①. The wheel cover can otherwise
not be fitted.
Tightening torque of wheel bolts
Specified tightening torque for wheel bolts for steel or alloy wheels:
Nm
If the wheel bolts are corroded and difficult to turn, they must be replaced before the tightening
torque is checked and the wheel hub threads cleaned.
Never grease or oil the wheel bolts or the threads of the wheel hub.
The tightening torque should be checked with a properly functioning torque wrench immediately
after changing a wheel.

WARNING
Incorrectly tightened wheel bolts can loosen while the vehicle is in motion and cause accidents,
serious injury, and loss of control of the vehicle.
easily.
bolts.
the wheel bolts only by approximately one turn before raising the vehicle with the vehicle
jack.
loosen while the vehicle is in motion, even if they have been tightened with the specified tightening
torque.
-on rings.
while the vehicle is in motion. The wheel bolts and the threads could be damaged if the tightening
torque is too high. Check the tightening torque regularly using a torque wrench.

WARNING
The wrong wheel bolts can loosen while the vehicle is in motion and cause accidents, serious injury,
and loss of control of the vehicle.

-piece wheel bolts: use only two-piece wheel bolts.
Lifting the vehicle with the jack

Fig. 205 Jacking points.

Fig. 206 Jack fitted at the rear on the left-side of the vehicle.
First read and observe the introductoryinformation and safety warnings⇒Introduction 
The jack may be positioned only at the reinforcements on the underbody, which are located behind
the markings on the body ⇒ Fig. 205 . Always use the jacking point closest to the wheel you are
working on ⇒ .
Checklist
For your own safety, carry out the following points in the specified order ⇒ :

Choose a firm and level surface suitable for lifting the vehicle.

Switch off the engine. Select a gear on vehicles with a manual gearbox or move the selector lever to
position P on vehicles with DSG® dual clutch gearbox DSG® dual clutch gearbox and switch on the
electronic parking brake Parking and manoeuvring.

Chock the wheel diagonally opposite using collapsible chocks or other suitable objects.

When towing a trailer : unhitch the trailer from the vehicle and park it properly.

Loosen the wheel bolts Wheel bolts.

Find the jacking point under the vehicle which is closest to the wheel that is being changed.

Insert the crank into the opening on the jack (depends on the vehicle equipment).

Crank up the jack until it just fits under the jacking point of the vehicle.

Ensure that the entire surface of the foot of the jack is resting securely on the floor, and that the
foot of the jack is positioned fully underneath the point of application and .

Position the jack and simultaneously continue to crank the claw up until it is in position around the
vertical rib underneath the vehicle .

Crank the jack further until the wheel is just clear of the ground.

WARNING
Incorrect use of the vehicle jack could cause the vehicle to slip off the jack. This could lead to severe
injuries. Observe the following points in order to reduce the risk of injuries:
jacks could slip out of position – this includes vehicle jacks supplied with other Volkswagen models.
the vehicle to slip off the jack. If necessary, use a large, sturdy board or similar support for the
vehicle jack.

side member securely ⇒ Fig. 206 .
lace any part of your body (e.g. an arm or leg) underneath the vehicle if the latter is
supported only by the vehicle jack.

vehicle.
cle when the engine is running, or if the vehicle is tilted to one side or on a
gradient.
cause the vehicle to fall off the vehicle jack.

WARNING
Ignoring any of the items on this important safety checklist can lead to accidents and severe injuries.

Changing a wheel

Fig. 207 Changing a wheel: removing the wheel bolts with the screwdriver handle.
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Removing a wheel
⇒ Preparations for changing a wheel .
⇒ Wheel bolts .
⇒ Lifting the vehicle with the jack .
⇒ Fig. 207 , completely unscrew the loosened
wheel bolts and place them on a clean surface.

Fitting the spare wheel or temporary spare wheel
y attention to the tyre direction of rotation ⇒ Tyre lettering and tyre type .

-theft wheel bolt using the adapter at position ⇒ Fig. 204②  or ③ and tighten it
slightly in a clockwise direction.
l the other wheel bolts in clockwise direction and tighten them slightly.

⇒ . Do not
tighten the bolts in order but always in diagonally opposite sequence.
⇒ Hubcaps .

WARNING
Incorrect tightening torque or incorrect use of wheel bolts can lead to a loss of control of the vehicle,
and cause accidents and serious injuries.
ep all wheel bolts and threads in the wheel hubs clean and free from oil and grease. The
wheel bolts must be easy to turn and be tightened to the specified torque.
not use
for loosening or tightening them.
After changing a wheel
First read and observe the introductoryinformation and safety warnings⇒Introduction 
luggage compartment ⇒ Vehicle toolkit .

⇒ Tightening torque of wheel
bolts .
as possible.

After changing a wheel, the indicator lamp for the tyre monitoring system may indicate a fault in the
system ⇒ Troubleshooting for Tyre Pressure Loss Indicator .
Breakdown set
Introduction
This chapter contains information on the followingsubjects:
⇒ Contents of the breakdown set 
⇒ Preparations 
⇒ Sealing and inflating tyres 

⇒ .
1.4 bar (20 psi/140 kPa) and higher:
⇒ Useful information about wheels and tyres .
80 km/h (50 mph).


WARNING
Driving with a tyre that cannot be sealed is dangerous and can cause accidents and serious injuries.
bar (19 psi/130 kPa) or lower.

Maintenance
Service
Service work and digital service schedule
The vehicle data attached to the inside cover of this owner's manual help ensure that you can have
the correct Volkswagen Genuine Parts® installed in your vehicle whenever required. It also
determines which type of service applies to your vehicle.
The vehicle data sticker confirms when the vehicle was first registered or delivered, when the pre-
delivery inspection was carried out, and thus the date from which your vehicle is covered by our
warranty.
Storing the service operations performed (digital service schedule)
Each service record is stored by your Volkswagen dealership and qualified workshop in a central
system. This transparent documentation of the service history allows the service operations
performed to be reproduced at any time. Each time you have your vehicle serviced, Volkswagen
recommends asking for a printed service record, which contains all service work stored in the
system.
With every service, the printout of the previous service record is replaced by a current printout.
The digital service schedule is not available in some markets. In this case, your Volkswagen
dealership will inform you about the documentation process for service work.
Service work
The following information is documented in the digital service schedule by your Volkswagen
dealership or qualified workshop:

Care allergen filter: change.


It is also possible to have servicing work carried out in between the scheduled service events
⇒ Fixed service or flexible service .
The scope of service is subject to change for technical reasons (continuous further development of
components). Your Volkswagen dealership or qualified workshop always has the latest information
about any changes.
Vehicle care
Notes on vehicle care
Regular, expert care helps to maintain your vehicle.
The longer contamination or dirt is left on the surface of vehicle components and upholstery fabrics,
the more difficult it can become to clean and treat them. Extended exposure may mean that it is no
longer possible to remove contamination or dirt.
Volkswagen recommend using Genuine care products that have been matched to your vehicle.1)
Consult a qualified workshop if you have any specific questions or if vehicle parts are not listed.

WARNING
Incorrect care and cleaning of vehicle components can impair the safety features of the vehicle and
cause serious injury.
be cleaned according to the manufacturer's instructions.

airbag modules.
ms against parts with sharp edges, e.g. when cleaning the insides of the
wheel housings.

WARNING
If the windows are covered in dirt, condensation, or ice, visibility will be reduced and the risk of
accidents and severe injuries will increase. This could impair the safety equipment of the vehicle.

-repellent window coating agents. In unfavourable
conditions, such coatings can cause increased dazzle.