15
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
1. When the liftgate reaches the desired height, push the rear liftgate close-button
P O U I F E P P S K B N P G U I F M J G U H B U F
P O D F 1 S F T T B O E I P M E U I F C V U U P O V O U J M U I F C V [ [ F S
T P V O E T U J N F T
2. To reset the height, with the liftgate open and not moving, press and hold the
rear liftgate close-button until the buzzer sounds 4 times, and continue to hold
until it buzzes again, then let go. Push the same button to close the liftgate.
When you next open the liftgate, it will open to the maximum height.
3. To set the height using the Multi-Information Display, press “
” or “” of the
meter control switches and select “
” from “” screen. Press “” or “” and
select “
1 # %
w B O E U I F O Q S F T T i.” Select “Opening Adjustment,” then
press “
w 4 F M F D U E F T J S F E Q P T J U J P O I F J H I U P Q U J P O T U P D I P P T F G S P N
U I F O Q S F T T
“
.”
For more details, refer to the Owner’s Manual.To automatically open/close Power Liftgate Quickly swipe your foot near the
lower center part of the rear bumper for within 1 second to trigger sensor. To
operate, make sure that the touchless sensor operation is enabled, the power
switch is OFF and that you are carrying the remote.
Rear door-Power Liftgate (if equipped)
Instrument panel
Power Liftgate (back door)
Hands-Free, Foot-Activated Power Liftgate
(if equipped)
Open: Push and hold
Close: Push and hold again
(close only)
Sensor area
(open only)
Carry Smart
Key remote
PROGRAMMABLE POWER LIFTGATE
NOTE:
- Installation of a tow hitch receiver or other accessories may require disabling
or removing the kick sensor.
- If battery is disconnected, the power back door needs to be reinitialized.
50
TOYOTA SAFETY SENSE™
Automatic High Beams (AHB)
ACTIVATING THE AHB SYSTEM
CONDITIONS WHERE AHB WILL TURN ON/OFF AUTOMATICALLY
When all of the following conditions are met, the high beams will be automatically
U V S O F E P O B G U F S B Q Q S P Y J N B U F M Z T F D P O E
t 7 F I J D M F T Q F F E J T B C P W F B Q Q S P Y J N B U F M Z N Q I L N I
• The area ahead of the vehicle is dark.
• There are no oncoming or preceding vehicles with headlights or tail lights
turned on.
• There are few streetlights on the road ahead.
If any of the following conditions occur, the high beams will be automatically turned off:
t 7 F I J D M F T Q F F E E S P Q T C F M P X B Q Q S P Y J N B U F M Z N Q I L N I
• The area ahead of the vehicle is not dark.
• Oncoming or preceding vehicles have headlights or tail lights turned on.
• There are many streetlights on the road ahead. 5 I F " V U P N B U J D ) J H I # F B N T " ) #
T B G F U Z T Z T U F N J T E F T J H O F E U P I F M Q Z P V T F F
more clearly at night. At speeds above 25 mph, AHB can detect the headlights of
oncoming vehicles and taillights of preceding vehicles, then automatically toggles
between high and low beams accordingly.
See Toyota.com/safety-sense for more information.
Refer to the Toyota Owner’s Manual for a list of additional situations in which the
system operation may be limited.
(2) (1)
1 S F T T U I F i
” switch.
1 V T I U I F M F W F S B X B Z G S P N Z P V X J U I U I F I F B E M J H I U T X J U D I J T J O U I F i
” or
“AUTO” position.
The AHB indicator will come on when the headlights are turned on automatically
to indicate that the system is active.
Note: Pull the lever back toward you or press the AHB switch to turn the AHB
system off.
The AHB indicator will turn off and “
” or “” will turn on. To activate the
system again, push the lever its original position or press the “
” switch.
