2021 TOYOTA MIRAI check engine

27
15,000 miles or 18 months
■Check installation of driver’s floor mat
■Inspect and adjust all fluid levels1
■Inspect FC HV battery cooling intake filter2
■Inspect wiper blades
■ Rotate tires ■ Visually inspect brake linings/drums and brake pads/discs
Inspect the following:
_ B

all joints and dust covers
_ B

rake lines and hoses
_ Dr

ive shaft boots
_ Fuel cell coolant level

Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Replace fuel cell air filter
■Tighten nuts and bolts on chassis and body
Extensive idling and/or low speed driving for a long distance such as po\
lice, taxi or
door-to-door delivery use:
■Inspect hydrogen supply system for leaks and damage
■Inspect hydrogen tank (with valve) for leaks and damage
■Inspect hydrogen tank band for damage
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Tighten nuts and bolts on chassis and body
Operating on rough or muddy roads, or roads with melted snow: ■Inspect hydrogen supply system for leaks and damage
■Inspect hydrogen tank (with valve) for leaks and damage
■Inspect hydrogen tank band for damage
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 P erform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.
_ Inverter coolant level
_ Steering gear
_ Steering linkage and boots
Dealer Service verification:
D
ate: Mileage:
Maintenance Log
MAINTENANCE LOG
MAINTENANCE

29
30,000 miles or 36 months
■Check installation of driver’s floor mat
■Inspect and adjust all fluid levels1
■Inspect FC HV battery cooling intake filter2
■Inspect wiper blades
■Replace cabin air filter
■Replace fuel cell air filter
■Replace ion exchanger element
■Rotate tires
Inspect the following:
_ B

all joints and dust covers
_ B

rake lines and hoses
_ B

rake linings/drums and
brake pads/discs
5
_ Dr ive shaft boots
_F

uel cell coolant level
_ F

uel cell cooling system for leaks
_ H

ybrid transaxle for signs of leakage
_H

ydrogen sensor
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 P erform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.5 Inspect thickness measurement and disc runout.
Dealer Service verification:
D
ate: Mileage:
_ H ydrogen supply system for leaks
and damag
e
_ H ydrogen tank (with valve) for leaks
and damage
_ H

ydrogen tank band for looseness
and damage
_ I

nverter coolant level
_ S

teering gear
_S

teering linkage and boots
Maintenance Log
MAINTENANCE LOG
MAINTENANCE

31
_ Inverter coolant level
_ Steering gear
_ Steering linkage and boots
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 P erform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.
Dealer Service verification:
D
ate: Mileage:
45,000 miles or 54 months
■Check installation of driver’s floor mat
■Inspect and adjust all fluid levels1
■Inspect FC HV battery cooling intake filter2
■Inspect wiper blades
■Rotate tires
■ Visually inspect brake linings/drums and brake pads/discs
Inspect the following:
_ Ball joints and dust covers
_ Brake lines and hoses
_ Drive shaft boots
_ Fuel cell coolant level
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Replace fuel cell air filter
■Tighten nuts and bolts on chassis and body
Extensive idling and/or low speed driving for a long distance such as po\
lice, taxi or
door-to-door delivery use:
■Inspect hydrogen supply system for leaks and damage
■Inspect hydrogen tank (with valve) for leaks and damage
■Inspect hydrogen tank band for damage
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Tighten nuts and bolts on chassis and body
Operating on rough or muddy roads, or roads with melted snow: ■Inspect hydrogen supply system for leaks and damage
■Inspect hydrogen tank (with valve) for leaks and damage
■Inspect hydrogen tank band for damage
Maintenance Log
MAINTENANCE LOG
MAINTENANCE

33
Dealer Service verification:
D
ate: Mileage:
60,000 miles or 72 months
■Check installation of driver’s floor mat
■Clean FC HV battery cooling intake filter2
■Inspect and adjust all fluid levels1
■Inspect wiper blades
■Replace breather pipe tip part (Gore film)
■Replace cabin air filter
■Replace fuel cell air filter
■Replace ion exchanger element
■Rotate tires
Inspect the following:
_ B

all joints and dust covers
_ B

rake lines and hoses
_ B

rake linings/drums and
brake pads/discs
5
_ Dr ive shaft boots
_F

uel cell coolant level
_ F

uel cell cooling system for leaks
_ H

ybrid transaxle for signs of leakage
_H

ydrogen sensor
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Replace hybrid transaxle fluid
■Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 P erform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.5 Inspect thickness measurement and disc runout.
_
H ydrogen supply system for leaks
and damag
e
_ H ydrogen tank (with valve) for leaks
and damage
_ H

ydrogen tank band for looseness
and damage
_ I

nverter coolant level
_ S

teering gear
_S

teering linkage and boots
Maintenance Log
MAINTENANCE LOG
MAINTENANCE

35
Dealer Service verification:
D
ate: Mileage:
75,000 miles or 90 months
■Check installation of driver’s floor mat
■Inspect and adjust all fluid levels1
■Inspect FC HV battery cooling intake filter2
■Inspect wiper blades
■Rotate tires
■ Visually inspect brake linings/drums and brake pads/discs
Inspect the following:
_ Ball joints and dust covers
_ Brake lines and hoses
_ Drive shaft boots
_ Fuel cell coolant level


Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Replace fuel cell air filter
■Tighten nuts and bolts on chassis and body
Extensive idling and/or low speed driving for a long distance such as po\
lice, taxi or
door-to-door delivery use:
■Inspect hydrogen supply system for leaks and damage
■Inspect hydrogen tank (with valve) for leaks and damage
■Inspect hydrogen tank band for damage
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Tighten nuts and bolts on chassis and body
Operating on rough or muddy roads, or roads with melted snow: ■Inspect hydrogen supply system for leaks and damage
■Inspect hydrogen tank (with valve) for leaks and damage
■Inspect hydrogen tank band for damage _ Inverter coolant level
_ Steering gear
_ Steering linkage and boots
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed
component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 P erform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.
Maintenance Log
MAINTENANCE LOG
MAINTENANCE

37
Dealer Service verification:
D
ate: Mileage:
90,000 miles or 108 months
■Check installation of driver’s floor mat
■Inspect and adjust all fluid levels1
■Inspect FC HV battery cooling intake filter2
■Inspect wiper blades
■Replace cabin air filter
■Replace fuel cell air filter
■Replace ion exchanger element
■Rotate tires
Inspect the following:
_ B

all joints and dust covers
_ B

rake lines and hoses
_ B

rake linings/drums and
brake pads/discs
4
_ Dr ive shaft boots
_F

uel cell coolant level
_ F

uel cell cooling system for leaks
_ H

ybrid transaxle for signs of leakage
_H

ydrogen sensor
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed
component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 Perform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.5 Inspect thickness measurement and disc runout.
_
H ydrogen supply system for leaks
and damag
e
_ H ydrogen tank (with valve) for leaks
and damage
_ H

ydrogen tank band for looseness
and damage
_ I

nverter coolant level
_ S

teering gear
_S

teering linkage and boots
Maintenance Log
MAINTENANCE LOG
MAINTENANCE

39
Dealer Service verification:
D
ate: Mileage:
105,000 miles or 126 months
■Check installation of driver’s floor mat
■Inspect and adjust all fluid levels1
■Inspect FC HV battery cooling intake filter2
■Inspect wiper blades
■Rotate tires
■ Visually inspect brake linings/drums and brake pads/discs
Inspect the following:
_ Ball joints and dust covers
_ Brake lines and hoses
_ Drive shaft boots
_ Fuel cell coolant level

Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Replace fuel cell air filter
■Tighten nuts and bolts on chassis and body
Extensive idling and/or low speed driving for a long distance such as po\
lice, taxi or
door-to-door delivery use:
■Inspect hydrogen supply system for leaks and damage
■Inspect hydrogen tank (with valve) for leaks and damage
■Inspect hydrogen tank band for damage
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Tighten nuts and bolts on chassis and body
Operating on rough or muddy roads, or roads with melted snow: ■Inspect hydrogen supply system for leaks and damage
■Inspect hydrogen tank (with valve) for leaks and damage
■Inspect hydrogen tank band for damage _ Inverter coolant level
_ Steering gear
_ Steering linkage and boots
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed

component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 Perform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.
Maintenance Log
MAINTENANCE LOG
MAINTENANCE

41
Dealer Service verification:
D
ate: Mileage:
120,000 miles or 144 months
■Check installation of driver’s floor mat
■Clean FC HV battery cooling intake filter2
■Inspect and adjust all fluid levels1
■Inspect wiper blades
■Replace breather pipe tip part (Gore film)
■Replace cabin air filter
■Replace fuel cell air filter
■Replace ion exchanger element
■Rotate tires
Inspect the following:
_ B

all joints and dust covers
_ B

rake lines and hoses
_ B

rake linings/drums and
brake pads/discs
5
_ Dr ive shaft boots
_F

uel cell coolant level
_ F

uel cell cooling system for leaks
_ H

ybrid transaxle for signs of leakage
_H

ydrogen sensor
Additional Maintenance Items for Special Operating Conditions3
Driving on dirt roads or dusty roads: ■Tighten nuts and bolts on chassis and body
Driving while towing, using a car-top carrier, or heavy vehicle loading:4
■Replace hybrid transaxle fluid
■Tighten nuts and bolts on chassis and body
1 Inspect sealed transmissions, transfer cases and differentials for signs of leakage. If any leakage from a sealed
component is suspected, it is recommended that you have the sealed component inspected by a Toyota dealer. Inspect
power steering fluid (if equipped) and brake fluid level/condition. Inspect engine and inverter (if equipped) coolant
level/condition/freezing point. Your dealer may recommend services (Dealer-Recommended Maintenance) based on
inspection results.
2 Visually check the FC HV battery cooling intake filter for dirt or dust every 5,000 miles and clean if necessary. Clean every
20,000 miles.
3 Perform these service items only if you drive primarily under the conditions indicated.4 N ot all vehicles are designed for towing. Refer to your Vehicle Owner’s Manual for details.5 Inspect thickness measurement and disc runout.6 Replace tank (with valve) every 15 years or 180 months whichever comes first.7 Replace inverter coolant at 150,000 miles and every 50,000 miles thereafter.
_
H ydrogen supply system for leaks
and damag
e
_ H ydrogen tank (with valve) for leaks
and damage6
_ H ydrogen tank band for looseness
and damage
_ I

nverter coolant level
7
_ S teering gear
_S

teering linkage and boots
Maintenance Log
MAINTENANCE LOG
MAINTENANCE