2021 SUZUKI JIMNY belt

Child restraint systems
60G332S
The following types of child restraint sys­tem are available generally.
Infant restraint
Child restraint
Booster seat
80JC008
SUZUKI highly recommends that you use a child restraint system to restrain infants and small children. Many different types of child restraint systems are available; check
FOR SAFE DRIVING
that the restraint system you select meets applicable safety standards.
All child restraint systems are designed to be secured in vehicle seats either by seat belts (lap belts or the lap portion of lap­shoulder belts) or by special rigid lower anchor bars built onto the floor. Whenever possible, SUZUKI recommends that child restraint systems be installed on the rear seat. According to accident statistics, chil­dren are safer when properly restrained in rear seating positions than in front seating positions.
(For countries applied for UN Regula­tion No.16) When purchasing a child restraint and install it to your SUZUKI vehicle, refer to the information about suitability for child restraints shown in "Child restraint system for countries applied for UN Regulation No.16" in this section.
NOTE: Observe any statutory regulation about child restraints.
1-18

Child restraint system for
countries applied for UN
Regulation No.16
.A. CAUTION
Adjust the height of the head restraint or remove it for fitting the child restraint, as necessary. How­ever, if a booster cushion not equipped with the head restraint is fitted, the head restraint should not be removed. If the head restraint is removed for fitting the child restraint, you need to install it again after removing the child restraint. If the child restraint is fitted improp­erly, a child sitting in it could be injured in a collision. (Refer to "Installation with lap-shoulder seat belts" section, 11lnstallation with ISO­FIX type anchorages" section and "Installation of child restraint with top tether11 section in this section for details.)
Child restraint
The suitability of each passenger's seat position for carriage of children and fitting of child restraint system is shown in the table.
Child restraint systems suitability for each seat position (for the vehicle with airbag deactivation switch)
The above illustration shows Left hand drive vehicle.
NOTE: Seat position number of G), @ and @ is same as Left hand drive vehicle for Right hand drive vehicle.
G) Front passenger's seat @ Rear seat right side @ Rear seat left side
G) (ID@ (#1. #2. #3)
(2) (ID~J,~ (#2, #3)
® (ID~J,~ (#2. #3)
FOR SAFE DRIVING
It is suitable for univer­sal category of child restraint system fixed with the vehicle seat belt.
It is suitable for i-Size and ISOFIX child restraint system.
This seat is equipped with Top tether anchor­age point.
Never use a rear-fac­ing child restraint sys­tem on the passenger seat when the front passenger airbag is activated.
#1: Move the front seat fully rearward. #2: When you install a forward-facing child restraint, if there is a gap or space between the child restraint and the seatback, adjust the seat­back angle in order to install the child restraint system properly. #3: If the head restraint interferes with the child restratint system, adjust the height of the head restraint or remove it, as necessary.
NOTE: For the Installation suitability of child restraint systems of Taiwan models, refer to "For Taiwan" in the "SUPPLE­MENT" section.
1-20

FOR SAFE DRIVING
Detailed information for child restraint system (for the vehicle with airbag deactivation switch)
Seating position
Seat position number
Seating position suitable for universal belted (YES/NO)
i-Size seating position (YES/NO)
Seating position suitable for lateral fixture (L 1/L2)
Suitable rear-facing fixture (R1/R2/R3)
Suitable front-facing fixture (F2X/F2/F3)
Key of letters to be inserted in the above table YES =Suitable for this seating position NO = Not suitable for this seating position
Front Passenger airbag is activated
NO
NO
NO
NO
NO
X =ISOFIX position is not suitable for ISOFIX child restraint systems in this fixture.
G)
ISOFIX child restraint systems are divided into different mass group, size class and fixture.
Front Passenger airbag is deactivated
YES
NO
NO
NO
NO
The child restraint system can be used in the seating positions for fixture shown in the above table. For mass group, size class and fixture, confirm the table of next page.
NOTE:
(2)
YES
YES
X
R1, R2
F2X, F2, F3
@
YES
YES·
X
R1, R2
F2X, F2, F3
For the Installation suitability of child restraint systems of Taiwan models, refer to "For Taiwan" in the "SUPPLEMENT' section.
1-21

FOR SAFE DRIVING
Installation suitability of SUZUKI recommendation child restraint systems (for the vehicle with airbag deactivation switch)
Recommendation of Mass group Child restraint system (#A)
0,0+ Britax Romer Baby-Safe i-Size (up to 13kg)
I Britax Romer Duo Plus (9kg to 18kg)
11, Ill Britax Romer Kid Fix XP (15kg to 36kg)
Key of letters to be inserted in the above table YES =It is suitable for this seating position NO = II is not suitable for this seating position
#1: Only belted.
Seating position
G)
Front Front (2) Passenger Passenger airbag is airbag is activated deactivated
NO YES (#1) YES (#1)
NO YES (#1) YES
NO YES (#1) YES
#A: These child restraint systems are SUZUKI Genuine Accessory, refer to the accessories catalog. However, there are countries which do not sell this child restraint system.
1-23
@
YES (#1)
YES
YES

Child restraint systems suitability for each seat position (for the vehicle with­out airbag deactivation switch)
The above illustration shows Left hand drive vehicle.
NOTE: Seat position number of G), @ and @ is same as Left hand drive vehicle for Right hand drive vehicle.
G) Front passenger's seat @ Rear seat right side @ Rear seat left side
G)
(#1, #2, #3)
~
(#2, #3)
@
(#2, #3)
(gJ
(g)@
[g)~l~
[g)~l~
It is suitable for univer­sal category of child restraint system fixed with the vehicle seat belt.
It is suitable for i-Size and ISOFIX child restraint system.
This seat is equipped with Top tether anchor­age point.
Never use a rear-fac­ing child restraint sys­tem on the passenger seat.
FOR SAFE DRIVING
#1: Move the front seat fully rearward. #2: When you install a forward-facing child restraint, if there is a gap or space between the child restraint and the seatback, adjust the seat­back angle in order to install the child restraint system properly. #3: If the head restraint interferes with the child restratint system, adjust the height of the head restraint or remove it, as necessary.
1-24

FOR SAFE DRIVING
Detailed information for child restraint system (for the vehicle without airbag deactivation switch)
Seat position number
Seating position suitable for universal belted (YES/NO)
· i-Size seating position (YES/NO)
Seating position suitable for lateral fixture (L 1 /L2)
Suitable rear-facing fixture (R1/R2/R3)
Suitable front-facing fixture (F2X/F2/F3)
Key of letters to be inserted in the above table YES =Suitable for this seating position NO = Not suitable for this seating position X =ISOFIX position is not suitable for ISOFIX child restraint systems in this fixture.
CD
YES (#1)
NO
NO
NO
NO
ISOFIX child restraint systems are divided into different mass group, size class and fixture. The child restraint system can be used in the seating positions for fixture shown in the above table. For mass group, size class and fixture, confirm the table of next page.
#1: When installing the child restraint systems, only a front-facing fixture is suitable.
1-25
Seating position
@
YES
YES
X
R1, R2
F2X, F2, F3
@
YES
YES
X
R1, R2
F2X, F2, F3

FOR SAFE DRIVING
Installation suitability of SUZUKI recommendation child restraint systems (for the vehicle without airbag deactivation switch)
Recommendation of Mass group Child restraint system (#A)
0,0+ Britax Romer Baby-Safe i-Size (up to 13kg)
I Britax Romer Duo Plus (9kg to 18kg)
II, II I Britax Romer KidFix XP (15kg to 36kg)
Key of letters to be inserted in the above table YES =II is suitable for this seating position NO = It is not suitable for this seating position
#1: Only belted.
G)
NO
YES (#1)
YES (#1)
#A: These child restraint systems are SUZUKI Genuine Accessory, refer to the accessories catalog. However, there are countries which do not sell this child restraint system.
1-27
Seating position
(2) @
YES (#1) YES (#1)
YES YES
YES YES

Approval mark to meet child
restraint system regulation for UN
R44 / R129 regulation
The following mark is shown on the child restraint system to meet the regulation of UN R44 / R129 for the child restraint sys­tem.
ECE R44/04 (1) ECE R129
Universal (2) i-Size
(3) -18kg Y (5) 40cm • 70cm I:!. 24kg (4)
@ (6) @
******** (7) ********
78RB01010
(1) Regulation number (2) Suitability for child restraint system category (3) Weight range of the applicable child who is applicable for this approval mark as shown in the mark (4) Height range and weight range of the applicable child who is applicable for this approval mark in the mark (5) Specification of appliance (6) Country code which approved child restraint system
(7) Approval number of child restraint seat
This approval mark is a representative example.
NOTE: UN R44 I R129 means the international regulation for the child restraint system. "EGE" is shown on the mark in the illus­tration for the child restraint system. This "EGE" mark is the same as "UN".
FOR SAFE DRIVING
Installation with lap-shoulder seat belts
A CAUTION
If your vehicle is equipped with the head restraint, adjust the height of the head restraint or remove it for fit­ting the child restraint, as necessary. However, if a booster cushion not equipped with the head restraint is fitted, the head restraint should not be removed. If the head restraint is removed for fitting the child restraint, you need to install it again after removing the child restraint. If the child restraint is fitted improp­erly, a child sitting in it could be injured in a collision.
NOTE: Stow the removed head restraint in the lug­gage compartment so it will not cause inconvenience to the occupants.
1-28