2021 NISSAN GT-R brake

Parking brake indicator:
When the ignition switch is in the ON
position, the light comes on when the
parking brake is applied.
Low brake fluid warning light:
When the ignition switch is in the ON
position, the light warns of a low brake
fluid level. If the light comes on while the
engine is running with the parking brake
not applied, stop the vehicle and perform
the following:
1. Check the brake fluid level. Add brakefluid as necessary. (
“Brake fluid”
page 8-11)
2. If the brake fluid level is correct, it is recommended you have the warning
system checked by a GT-R certified
NISSAN dealer.
Anti-lock Braking System (ABS) warning
indicator:
When the parking brake is released and
the brake fluid level is sufficient, if both
the brake warning light and the Anti-lock
Braking System (ABS) warning light illu-
minate, it may indicate the ABS is not
functioning properly. It is recommended
you have the brake system checked, and
if necessary repaired, by a GT-R certified
NISSAN dealer promptly. (
“Anti-lock
Braking System (ABS) warning light” page 2-29)
Brake pad wear warning indicator
(models with NCCB (NISSAN Carbon
Ceramic Brake) package):
When the brake warning light illuminates,
it may indicate that there is brake pad
wear. Have the brake system checked
and brake pads replaced as soon as
possible. It is recommended you contact
a GT-R certified NISSAN dealer for this
service.
WARNING
.
Your brake system may not be
working properly if the warning
light is on. Driving could be dan-
gerous. If you judge it to be safe,
drive carefully to the nearest
service station for repairs. Other-
wise, have your vehicle towed because driving it could be dan-
gerous.
. Pressing the brake pedal with the
engine stopped and/or low brake
fluid level may increase your
stopping distance and braking
will require greater pedal effort
as well as pedal travel.
. If the brake fluid level is below the
minimum or MIN mark on the
brake fluid reservoir, do not drive
until the brake system has been
checked. It is recommended you
contact a GT-R certified NISSAN
dealer.
Charge warning light
If the light comes on while the engine is
running, it may indicate the charging
system is not functioning properly. Turn
the engine off and check the alternator
belt. If the belt is loose, broken, missing or
if the light remains on, it is recommended
you see a GT-R certified NISSAN dealer
immediately.
Instruments and controls
2-27

WARNING/INDICATOR LIGHTS (yel-
low)See
“Warning display” page 2-36 and
“Vehicle information display” page 2-
13.
warning light comes on when the
ignition switch is pushed to ON. It turns
off soon after the engine is started.
If the AWD system malfunctions, the
warning light will either remain illumi-
nated or blink. (
“All-Wheel Drive
(AWD)” page 5-42)
“Tire and loading infor-
mation label” page 10-14)
If the tire pressure is insuffi-
cient, fill with nitrogen gas. It
is recommended you contact
a GT-R certified NISSAN dealer
about filling with nitrogen
gas. If nitrogen gas is not
available, compressed air
may be safely used under
normal driving conditions. However, NISSAN recom-
mends refilling with nitrogen
gas for maximum tire perfor-
mance.
. If the warning light is still on after
the above operations, have your
vehicle checked as soon as pos-
sible. It is recommended you have
the vehicle checked by a GT-R
certified NISSAN dealer.
or
Anti-lock Braking
System (ABS) warning light
When the ignition switch is in the ON
position, the Anti-lock Braking System
(ABS) warning light illuminates and then
turns off. This indicates the ABS is opera-
tional.
If the ABS warning light illuminates while
the engine is running, or while driving, it
may indicate the ABS is not functioning
properly. It is recommended you have the
system checked by a GT-R certified
NISSAN dealer.
If an ABS malfunction occurs, the anti-
lock function is turned off. The brake
system then operates normally, but with-
out anti-lock assistance. (
“Brake sys-
tem” page 5-52)
Instruments and controls
2-29

position and the
ignition switch is in the ON position.
. The shift lever is in the
position and
5 minutes have passed while the
ignition switch is in the ON position.
Be sure to move the shift lever out of the
position after driving in reverse.Brake pad wear warning (models
without NCCB (NISSAN Carbon
Ceramic Brake) package)The disc brake pads have audible wear
warnings. When a brake pad requires
replacement, it will make a high pitched
scraping sound when the vehicle is in
motion. This scraping sound will first
occur only when the brake pedal is
depressed. After the wear of the brake
pad is increased, the sound will be heard all the time even if the brake pedal is not
depressed. Have the brakes checked as
soon as possible if the warning sound is
heard.
Instruments and controls
2-35

ANTI-LOCK BRAKING SYSTEM
(ABS) WARNINGThis will appear if the Anti-lock Braking
System (ABS) is not functioning properly.
(
“Anti-lock Braking System (ABS)
warning light” page 2-29) (
“Brake
warning light” page 2-26)
“Vehicle Dynamic Control (VDC)
warning light” page 2-34) (
“Vehicle
Dynamic Control (VDC) off indicator light”
page 2-33)
“All-Wheel Drive (AWD) warning light”
page 2-29)
NOTE:
If the vehicle is driven in a way which
causes the rear wheels to slip, the AWD
clutch temperature will increase and
the warning indicator may flash. Con-
tinuing to drive in way that causes the
warning light to flash may cause the
clutch to reach excessive temperatures

ENGINE START OPERATION INDI-
CATORThis indicator appears when the shift
lever is in the
position.
This indicator means that the engine will
start by pushing the ignition switch with
the brake pedal depressed.
position.
If this warning appears, move the shift
lever to the
position. This warning will
also turn off when pushing the ignition
switch to the ON position.
position with the
ignition switch in the ACC position after
the SHIFT
warning appears.
If this warning appears, push the ignition
switch to the OFF position.

position
.
2. Push the ignition switch to the ON position.
3. The autolight system automatically turns the headlights on and off.
To turn the autolight system off, turn the
switch to the
position.
The autolight system can turn on the
headlights automatically when it is dark and turn off the headlights when it is
light.
If the ignition switch is pushed to the ON
position when the parking brake is ap-
plied, the headlights remain off.
With the
position selected, the head-
lights turn off when the ignition switch is
pushed to the OFF position, the shift lever
is placed in the
position or the parking
brake is applied. (The parking, side mar-
ker, tail, license plate, and instrument
lights are on.)
With the AUTO position selected (head-
lights are on), the headlights will remain
on for 45 seconds when the ignition
switch is placed in the OFF position and
one of the doors is opened.
Instruments and controls
2-55

switch is pushed to the OFF position.position, the headlight must be off. Turn
the headlight switch to the
position
for full illumination when driving at night.
If the parking brake is applied before the
engine is started, the daytime running
lights do not illuminate. The daytime
running lights illuminate once the parking
brake is released. The daytime running
lights will remain on until the ignition
switch is pushed to the OFF position or
the headlights turn on.
Turn signal
Move the lever up or down to signal the
turning direction. When the turn is com-
pleted, the turn signals cancel automati-
cally.

enter the park-
ing space
.
4. Maneuver the steering wheel to make the vehicle width guide lines
parallel
to the parking space
while referring to the predictive course lines.
5. When the vehicle is parked in the space completely, move the shift lever
in an appropriate gear and apply the
parking brake.