2021 NISSAN GT-R cruise control

. The SET
indicator will turn off.
. Tap the brake pedal. The SET
indicator will turn off.
. Turn the MAIN switchoff. Both the
CRUISE indicator and SET indicator will
turn off. NOTE:
.
If cruise control was canceled by
pressing the cancel switch or by
depressing the brake pedal, the
system changes to standby status.
. If you depress the brake pedal while
pushing the RESUME/ACCELERATE
or SET/COAST switch and reset at
the cruising speed, the cruise control
will be deactivated. Turn the MAIN
switch off once and then turn it on
again.
Under the following conditions, cruise
control will be automatically canceled.
. Vehicle speed drops to below approxi-
mately 19 MPH (30 km/h).
. Vehicle speed drops to more than
approximately 8 MPH (13 km/h) below
the set vehicle speed.
. The shift lever is moved to a position
other than

wheels will lose even more trac-
tion.
. Allow more stopping distance
under these conditions. Braking
should be started sooner than on
dry pavement.
. Allow greater following distances
on slippery roads.
. Watch for slippery spots (glare
ice). These may appear on an
otherwise clear road in shaded
areas. If a patch of ice is seen
ahead, brake before reaching it.
Try not to brake while on the ice,
and avoid any sudden steering
maneuvers.
. Do not use the cruise control on
slippery roads.
. Snow can trap dangerous ex-
haust gases under your vehicle.
Keep snow clear of the exhaust
pipe and from around your vehi-
cle.
NOTE:
When driving on snow, select the SAVE
mode with the setup switch. By select-
ing the SAVE mode, the engine output is
controlled appropriately for snow or slippery road surfaces. This enables
the vehicle to start or accelerate
smoothly.
ENGINE BLOCK HEATER (if so
equipped)Engine block heaters are used to assist
with cold temperature starting.
The engine block heater should be used
when the outside temperature is 20°F
(−7°C) or lower.To use the engine block heater1. Turn the engine off.
2. Plug the engine block heater cord into
a grounded 3-wire, 3-pronged exten-
sion cord.
3. Plug the extension cord into a Ground Fault Interrupt (GFI) protected,
grounded 110-volt AC (VAC) outlet.
4. The engine block heater must be plugged in for at least 2 - 4 hours,
depending on outside temperatures,
to properly warm the engine coolant.
Use an appropriate timer to turn the
engine block heater on.
5. Before starting the engine, unplug and properly store the cord to keep it
away from moving parts.

Checking engine coolant level ..................... 8-8
Draining of coolant water ............................ 5-57
Engine coolant temperature gauge ........ 2-8
Coolant level and mixture ratio ................ GTR-15
Corrosion protection ................................................... 7-9
Cracks on brake pad ......................................... GTR-28
Cracks on the disc rotors .............................. GTR-28
Cruise control ................................................. 2-17, 5-35
Cruise control operations .................................... 5-37
Cruise control system warning ....................... 2-43
Cup holders ..................................................................... 2-63
Current fuel consumption ................................... 2-16
D
E

Do not use the cruise control when
driving under the following condi-
tions. Doing so could cause a loss of
vehicle control and result in an acci-
dent.
.When it is not possible to keep
the vehicle at a set speed.
. In heavy traffic or in traffic that
varies in speed.
. On winding or hilly roads.
. On slippery roads (rain, snow, ice,
etc.).
. In very windy areas.
NOTE:
. When the SAVE mode is selected
with the transmission setup switch,
the acceleration and deceleration
can be controlled smoothly. When
the SAVE mode is selected, the
maximum setting speed is lower
than the one in the normal mode. When the vehicle approaches a gen-
tle uphill, there may be a slight delay
as the vehicle returns to the preset
speed. However, the vehicle will
gradually accelerate and return to
the preset speed.
PRECAUTIONS ON CRUISE CON-
TROL.
If the cruise control system malfunc-
tions, it will cancel automatically. The
SET indicator will blink and the cruise
control system warning will appear to
warn the driver. (
“Cruise control
system warning” page 2-43)
. If the engine coolant temperature
becomes excessively high, the cruise
control system will be canceled auto-
matically.
. If the SET indicator blinks, turn the
cruise control main switch off and it is
recommended you contact a GT-R
Starting and driving
5-35
CRUISE CONTROL

. The SET
indicator will turn off.
. Tap the brake pedal. The SET
indicator will turn off.
. Turn the MAIN switchoff. Both the
CRUISE indicator and SET indicator will
turn off. NOTE:
.
If cruise control was canceled by
pressing the cancel switch or by
depressing the brake pedal, the
system changes to standby status.
. If you depress the brake pedal while
pushing the RESUME/ACCELERATE
or SET/COAST switch and reset at
the cruising speed, the cruise control
will be deactivated. Turn the MAIN
switch off once and then turn it on
again.
Under the following conditions, cruise
control will be automatically canceled.
. Vehicle speed drops to below approxi-
mately 19 MPH (30 km/h).
. Vehicle speed drops to more than
approximately 8 MPH (13 km/h) below
the set vehicle speed.
. The shift lever is moved to a position
other than

wheels will lose even more trac-
tion.
. Allow more stopping distance
under these conditions. Braking
should be started sooner than on
dry pavement.
. Allow greater following distances
on slippery roads.
. Watch for slippery spots (glare
ice). These may appear on an
otherwise clear road in shaded
areas. If a patch of ice is seen
ahead, brake before reaching it.
Try not to brake while on the ice,
and avoid any sudden steering
maneuvers.
. Do not use the cruise control on
slippery roads.
. Snow can trap dangerous ex-
haust gases under your vehicle.
Keep snow clear of the exhaust
pipe and from around your vehi-
cle.
NOTE:
When driving on snow, select the SAVE
mode with the setup switch. By select-
ing the SAVE mode, the engine output is
controlled appropriately for snow or slippery road surfaces. This enables
the vehicle to start or accelerate
smoothly.
ENGINE BLOCK HEATER (if so
equipped)Engine block heaters are used to assist
with cold temperature starting.
The engine block heater should be used
when the outside temperature is 20°F
(−7°C) or lower.To use the engine block heater1. Turn the engine off.
2. Plug the engine block heater cord into
a grounded 3-wire, 3-pronged exten-
sion cord.
3. Plug the extension cord into a Ground Fault Interrupt (GFI) protected,
grounded 110-volt AC (VAC) outlet.
4. The engine block heater must be plugged in for at least 2 - 4 hours,
depending on outside temperatures,
to properly warm the engine coolant.
Use an appropriate timer to turn the
engine block heater on.
5. Before starting the engine, unplug and properly store the cord to keep it
away from moving parts.

Brake warning light2-26Charge warning light 2-27Engine oil pressure warning
light2-28Seat belt warning light
2-28Supplemental air bag
warning light2-28Yellow
light Name
Page
All-Wheel Drive (AWD)
warning light 2-29Anti-lock Braking System
(ABS) warning light2-29Intelligent Key warning
light2-30Low tire pressure warning
light
2-30Malfunction Indicator Light
(MIL) 2-32Master warning light
2-32Transmission warning light2-33Vehicle Dynamic Control
(VDC) off indicator light2-33Vehicle Dynamic Control
(VDC) warning light2-34Other
light Name
Page
Cruise main switch indica-
tor light 2-34Cruise set switch indicator
light2-34Exterior light indicator
2-34Front passenger air bag
status light2-34High beam indicator light
2-34Turn signal/hazard indica-
tor lights2-34
WARNING AND INDICATOR LIGHTS

2. NEXT switch3. Vehicle information displayThe drive computer displays the following
information:
.Current fuel consumption
. Vehicle speed
. Cruise control
. Average fuel consumption and speed
. Elapsed time and trip computer
. Distance to empty
. Outside air temperature
. Setting .
Warning
The vehicle information display
can be
changed when the ignition switch is in
the ON position. Push the ENTER switch
to change the display.
NOTE:
. The cruise control display is shown if
cruise control is set. (
“Cruise
control” page 5-35)
. The warning display is not shown if
there are no conditions to warn the
driver.
. Depending on the driving conditions
and other factors, the displayed
values may differ from the actual
values.
. The position of the speedometer
needle and the speed shown in the
vehicle information display may
slightly differ.
CURRENT FUEL CONSUMPTIONThe current fuel economy is displayed
when driving.
DRIVE COMPUTER