2021 MERCEDES-BENZ E-CLASS ESTATE tyre pressure

The
following bicycle rack designs are possible:
R When mounted byattaching toball head 1,
th e maximum load capacity is 75 kg. You can
transport up tothre e bicycles.
R When mounted on ball head 1and guide pin
2, the maximum load capacity is 100 kg. Yo u
can transport up tofour bicycles.
The maximum load capacity is calculate d fromthe
we ight of the bicycle rack and the bicycle rack
load.
Obser vethe no tes on driving with a roof load,
trailer or fully laden vehicle (/ page 182).
When using a bicycle rack , set the tyre pressure
fo r increased load on there ar axle of theve hicle.
Fu rther information on the tyre pressure can be
fo und in the tyre pressure table (/ page 413).
N
No ot tes on loading
es on loading
The lar gerth e distance between the load's centre
of grav ity and the ball head, thegre ater the load
on the trailer hitch. Obser
vethefo llowing no tes:
R mount heavy bicycles as close totheve hicle
as possible
R always distribute the load on the bicycle rack
as evenly as possible across theve hicle's lon-
gitudinal axis
Mercedes-Benz recommends removing all de tach-
able parts from bicycles (e.g. bask ets, ch ild seats,
re ch arge able batteries) before loading them onto
th e bicycle rack . This will impr ovethe aerody-
namic resis tance and centre of grav ity of the bicy-
cle rack.
Alw ays secure the bicycles toprev ent them from
moving around and check them at regular inter-
va ls to ensure that they are secure.
Do not use tarp aulins or other co vers. The driving
ch aracteristics and rear view may be impaired. In
addition, aerodynamic resis tance and the load on
th e trailer hitch will increase. Load distribution on
the bicycle rack
1 Vertical distance between centre of grav ity
and ball head
2 Horizontal distance between centre of grav ity
and ball head
3 The centre of grav ity is on theve hicle's cent re
axis
Obser vethefo llowing information when loading
th e bicycle rack: 294
294
Driving and parking

R
In automatic car washes with con veyor sys-
te ms:
- Neutral iis engaged.
- Ifyo uwo uld like tolea vetheve hicle while
it is being washed, make sure theke y is
located in theve hicle. The park position
j isotherwise automatically engaged.
% If, aTer the car wash, youre mo vethewax
from the windscreen and wiper rubbers, this
will pr event smearing and reduce wiper noise. Inf
Inf
or
ormation on using a high-pr
mation on using a high-pr essur
essure cleaner
e cleaner &
W
W ARNING
ARNING Risk of an accident when using
high-pressure cleaners with round-spr ay
nozzles
The water jet can cause extern ally invisible
damage.
Components damaged in this wa y may un ex-
pectedly fail. #
Do not use a high-pressure cleaner with
ro und-spr aynozzles. #
Have damaged tyres or chassis parts
re placed immediatel y. To
avo id damage toyour vehicle, obser vethefo l-
lowing when using a high-pressure cleaner:
R The key is at a minimum dis tance of 3 m away
from theve hicle. Otherwise theta ilgate could
open unintentionall y.
R Maintain a distance of at least 30 cm tothe
ve hicle.
R V Vehicles wit
ehicles with decor h decorativ
ative f
e foil:
oil: Parts of your
ve hicle are co vered with a decorative foil.
Maintain a distance of at least 70 cm between
th efo il-co vered parts of theve hicle and the
nozzle of the high-pressure cleaner. Mo vethe
high-pressure cleaner nozzle around whilst
cleaning. The waterte mp erature of the high-
pressure cleaner must not exceed 60°C.
R Obser vethe information on the cor rect dis-
ta nce in the equipment manufacturer's oper-
ating inst ructions.
R Do not direct the nozzle of the high-pressure
cleaner directly at sensitive parts, such as tyres,
gaps, electrical components, batteries,
light sources and ventilation slits. W W
ashing t
ashing t he v
he vehicle b
ehicle b y hand
y hand *
N
NOOTE
TE Engine damage due towa ter ing ress #
Take care not topoint thewa ter jet
directly towa rdsth e air inlet grille below
th e bonnet. obser
vethe legal requ irements, e.g. in a number
of countries, washing byhand is only permitted in
special lydesignated wash ba ys. #
Use a mild cleaning agent, e.g. car shampoo. #
Washtheve hicle with luk ewarm water using a
soT car sponge. When doing so, do not
ex pose theve hicle todirect sunlight. #
Carefully hose theve hicle o. with water and
dry using a chamois.
% Obser vethe no tes on the care of car parts
(/ page 385). Maintenance and care
383
383

R
vehicle vib ration
R smo kewhich smells like rubber
R continuous ESP ®
inter vention
R crac ksinthe tyre side walls #
ATer driving in emer gency mode, ha ve
th erims checkedby a quali/ed specialist
wo rkshop with rega rd totheir fur ther
use. #
The defective tyre must be replaced in
ev ery case. Wi
th MOEx tended tyres (run-0at tyres), you can
continue todrive your vehicle even if there is a
to ta l loss of pressure in one or more tyres. Ho w-
ev er, the tyre a.ected must not show any clear ly
visible damage.
Yo u can recognise MOExtended tyres bythe
MOEx tended ma rking which appears on the side
wa ll of the tyre.
V
V ehicles wit ehicles wit h tyr
h tyre pr
e pressur
essur e loss w
e loss w ar
ar ning syst
ning syst em:
em:
MOExtended tyres may only be used in conjunc-
tion with an activated tyre pressure loss warning
system. V
V
ehicles wit
ehicles wit h tyr
h tyre pr
e pressur
essur e monit
e monit or
oring sy
ing sy st
stem:
em:
MOExtended tyres may only be used in conjunc-
tion with an activated tyre pressure monitoring
system.
If a pressure loss warning message appears inthe
driver's displa y,proceed as follo ws:
R Check the tyre for damage.
R If driving on, obser vethefo llowing no tes.
Dr
Dr iving dist iving dist ance possible in emerg
ance possible in emerg ency mode
ency mode
aTer
aTer t
the pr
he pr essur
essur e loss w
e loss w ar
arning:
ning: Load condition
Load condition
Dr
Driving dist
iving dist ance possi-
ance possi-
ble in emerg
ble in emerg ency mode
ency mode
Pa rtially laden 80 km
Fu lly laden 30 km The driving distance possible in emer
gency mode
may vary depending on the driving style. Obser ve
th e maximum permissible speed of 80 km/h.
If a tyre has gone 0at and cannot be replaced with
an MOExtended tyre, you can use a standard tyre
as a temp orary measure. TIREFIT kit st
TIREFIT kit st
or
orag
ag e location
e location The TIREFIT kit is located under
the load compart-
ment 0oor. 1
Tyre sealant bottle
2 Tyre in0ation compressor
Depending on the model, the TIREFIT kit may also
be located in other places under the load com-
partment 0oor.
% You can /nd information on the po wer cate-
gory (LK) and/or electrical data on the back
of the tyre in0ation compressor:
R LK2 – 12 V/15 A,180 W,0.8 kg 392
392
Breakdown assistance

At
a dis tance of app roximately 1 m tothe tyre
in0ation compressor and appr oximately 1.6 m
abo vethegr ound, thefo llowing sound pres-
sure le vels appl y:
R Emission sound pressure le vel L
PA 83 dB
(A)
R Sound po wer le vel L
WA 91 dB (A)
The tyre in0ation compressor is maintenance-
free. If there is a malfunction, please contact
a qu ali/ed specialist workshop. Using t Using t
he TIREFIT kit
he TIREFIT kit R
R
eq
eq uir
uir ements:
ements:
R Tyre sealant bottle and tyre in0ation compres-
sor (/ page 392)
R TIREFIT stic ker
R Gloves
Yo u can use TIREFIT tyre sealant toseal per fora-
tion damage of up to4 mm, particular lythose in
th e tyre contact sur face. You can use TIREFIT in
outside temp eratures down to-20 °C. &
W
WARNING
ARNING Risk of accident when using
tyre sealant
The tyre sealant may be unable toseal the
tyre proper ly, especially in thefo llowing cases:
R there are lar gecuts or punctures in the
tyre (la rger than damage pr eviously men-
tioned)
R the wheel rims ha vebeen damaged
R aTer journe yswith very low tyre pressure
or with 0at tyres #
Do not continue driving. #
Consult a quali/ed specialist workshop. &
W
WARNING
ARNING Risk of injury and poisoning
from tyre sealant
Ty re sealant is hazardous tohealth and causes
ir rita tion. Do not allow it tocome into contact
with your skin, eyes or clo thing, and do not
swallow it. Do not inhale any vapours. Keep
th e tyre sealant away from children. Obser
vethefo llowing if you come into contact
with the tyre sealant: #
Rinse o. the tyre sealant from your skin
using water immediatel y. #
If tyre sealant gets into your eyes, thor-
oughly rinse them using clean water
immediatel y. #
If tyre sealant has been swallo wed,thor-
oughly rinse out your mouth immediately
and drink plenty of water. Do not induce
vo miting and seek medical attention
immediatel y. #
Change out of clo thing which has come
into contact with tyre sealant immedi-
atel y. #
If an alle rgic reaction occurs, seek medi-
cal attention immediatel y. *
N NO
OTE
TE Overheating due tothe tyre in0ation
compressor running too long #
Do not runth e tyre in0ation compressor
fo r longer than ten minutes without inter-
ru ption. Breakdown assistance
393 393

Comply with
the manufacturer's saf ety no tes on
th e stic ker on the tyre in0ation compressor.
Ha ve the tyre sealant bottle replaced in a quali/ed
specialist workshop every /ve years. #
Do not remo veany fore ign objects which ha ve
entered the tyre. #
A1x part 1ofthe TIREFIT stic kerto the
inst rument clus ter within the driver's /eld of
vision. #
A1x part 2ofthe TIREFIT stic ker near the
va lve on the wheel with the defective tyre. #
Pull plug 4with the cable and hose 5out
of the tyre in0ation compressor housing. #
Push the plug of hose 5into 0an ge6 of
tyre sealant bottle 1until the plug engages. #
Place tyre sealant bottle 1head down wards
into recess 2ofthe tyre in0ation compres-
sor. #
Remo vetheva lve cap from valve 7 onthe
fa ulty tyre. #
Screw /lling hose 8onto valve 7. #
Insert plug 4into a 12 V soc ket in your vehi-
cle. #
Switch on theve hicle. #
Switch on the tyre in0ation compressor using
On/O. switch 3.
The tyre is in0ated. Firs t, tyre sealant is pum-
ped into the tyre. The pressure may brie0y rise
to appr oximately 500 kPa (5.0 bar/73 psi).
Do no
Do no t switc
t switc h
ho.
o. t
the tyr
he tyr e
ein0ation
in0ation com
compr
pressor
essor
dur
dur ing t
ing t his phase!
his phase! 394
394
Breakdown assistance

#
Let the tyre in0ation compressor runfo r a
maximum of ten minutes.
The tyre should then ha veattained a tyre pres-
sure of at least 200 kPa (2.0 bar/29 psi).
If tyre sealant leaks out, make sure you clean the
a.ected area as quickly as possible. It is prefera-
ble touse clean water.
If yo uget tyre sealant on your clo thing, ha veit
cleaned as soon as possible with per chloroe thy-
lene.
If,
If, aTer aTer t
ten minut
en minut es, a tyr
es, a tyre pr
e pressur
essur e of 200 kPa
e of 200 kPa
(2.0 bar/29 psi) has no
(2.0 bar/29 psi) has no t been att
t been att ained:
ained: #
Switch o. the tyre in0ation compressor. #
Unscr ewthe /lling hose from theva lve of the
defective tyre.
Please no tethat tyre sealant may leak out when
unscr ewing the /lling hose. #
Drive forw ards or in reve rseve ry slo wly for
appr oximately 10 m. #
Pump up the tyre again.
ATer a maximum of ten minutes the tyre pres-
sure must be at least 200 kPa (2.0 bar/
29 psi). &
W WARNING
ARNING Risk of accident due tothe
speci/ed tyre pressure not being attained
If th e speci/ed tyre pressure is not attained
aTer the speci/ed time, the tyre is too badly
damaged. The tyre sealant cannot repair the
tyre in this instance.
The braking and driving characteristics may be
gr eatly impaired. #
Do not continue driving. #
Consult a quali/ed specialist workshop. If,
If,
aTer
aTer t
ten minut
en minut es, a tyr
es, a tyre pr
e pressur
essur e of 200 kPa
e of 200 kPa
(2.0 bar/29 psi) has been att
(2.0 bar/29 psi) has been att ained:
ained: #
Switch o. the tyre in0ation compressor. #
Unscr ewthe /lling hose from theva lve of the
defective tyre. &
W
WARNING
ARNING Risk of accident from driving
with sealed tyres
A tyre temp orarily sealed with tyre sealant
impairs the handling characteristics and is not
suitable for higher speeds. #
Adapt your driving style accordingly and
drive carefull y. #
Do not exceed the maximum speed limit
with a tyre that has been repaired using
tyre sealant. #
Obser vethe maximum permissible speed for a
tyre sealed with tyre sealant 80 km/h.
* N
NOOTE
TE Staining from leaking tyre sealant ATer use,
excess tyre sealant may leak out
from the /lling hose. #
Therefore, place the /lling hose in the
plastic bag that contained the TIREFIT
kit. Breakdown assistance
395
395

+
ENVIR
ENVIR
ONMENT
ONMENT AL NO
AL NOTE
TE Environmen tal
pollution caused byenvironmentally ir re-
sponsible disposal Ty
re sealant contains pollu tants. #
Have the tyre sealant bottle disposed of
professionall y,e.g. at a Mercedes-Benz
Service Centre. #
Stow the tyre sealant bottle and the tyre in0a-
tion compressor. #
Pull away immediatel y. #
Stop driving aTer appr oximately ten minutes
and check the tyre pressure using the tyre
in0ation compressor.
The tyre pressure must now be at least
130 kPa (1.3 bar/19 psi). &
W WARNING
ARNING Risk of accident due tothe
speci/ed tyre pressure not being attained
If th e speci/ed tyre pressure is not reached,
th e tyre is too badly damaged. The tyre seal-
ant cannot repair the tyre in this instance. The braking and driving
characteristics may be
gr eatly impaired. #
Do not continue driving. #
Consult a quali/ed specialist workshop. Countr
Countr
ies t
ies that hav
hat hav e Mer
e Mercedes-Benz Ser
cedes-Benz Ser vice24h:
vice24h:
yo u will /nd a stic ker with thete lephone number,
e.g. on the B‑pillar on the driver's side. #
Correct the tyre pressure if it is still at least
130 kPa (1.3 bar/19 psi). See the tyre pres-
sure table on the fuel /ller 0ap forva lues. #
T
T o incr
o incr ease t
ease t he tyr
he tyre pr
e pressur
essur e:
e:switch on the
tyre in0ation compressor. #
T To r o r educe t
educe t he tyr
he tyre pr
e pressur
essur e:
e:press pressure
re lease button 1next tomanome ter2. #
When the tyre pressure is cor rect, unscr ew
th e /lling hose from theva lve of the sealed
tyre. #
Screw theva lve cap onto theva lve of the
sealed tyre. #
Pull the tyre sealant bottle out of the tyre in0a-
tion compressor.
The /lling hose st ays on the tyre sealant bot-
tle. #
Drive tothe nearest quali/ed specialist work-
shop and ha vethe tyre, tyre sealant bottle and
/lling hose replaced there. Batt Batt
er
ery (v
y (v ehicle)
ehicle) N
No
ot
tes on t
es on t he 12 V batt
he 12 V batt ery
ery &
W
WARNING
ARNING Risk of an accident due towo rk
car ried out incor rectly on the battery
Wo rkcar ried out incor rectly on the battery
can, forex ample, lead toa short circuit. This 396
396
Breakdown assis
tance

N
N
o
ot
tes on noise or unusual handling c
es on noise or unusual handling c har
haract
acter
eris-
is-
tics
tics
Make sure there are no vibrations, noises or
unusual handling characteristics when theve hicle
is in motion. This may indicate that the wheels or
tyres are damaged. Hidden tyre damage could
also be causing the unusual handling characteris-
tics.
If yo u suspect that a tyre is defecti ve,re duce your
speed immediately and ha vethe tyres and wheels
ch ecked at a quali/ed specialist workshop. N No
ot
tes on r
es on r egularl
egularly inspecting wheels and tyr
y inspecting wheels and tyr es
es &
W
WARNING
ARNING Risk of injury due todamaged
tyres
Damaged tyres can cause tyre pressure loss. #
Check the tyres regula rly fo r signs of
damage and replace any damaged tyres
immediatel y. &
W
WARNI NG
ARNI NGRisk of aquaplaning due to
insu1cient tyre tread
Insu1cient tyre tread will result in reduced
tyre grip.
The risk of aquaplaning is increased on wet
ro ads, especially when the speed of theve hi-
cle is not adap tedto suit the conditions. #
Thus, you should regula rly ch eck the
tread dep thand the condition of the
tread across the entire width of all tyres.
Minimum tread dep thfor:
R Summer ty res: 3 mm
R M+S tyres: 4 mm #
For saf etyre asons, replace the tyres
before the legall y-prescribed limit forthe
minimum tread dep thisreached. Car
ryout thefo llowing checks on all wheels regu-
lar ly, at least once a month or as required, for
ex ample, prior toa long jou rney or driving o.-
ro ad:
R Check the tyre pressure (/ page 412). R
Visually inspect wheels and tyres for damage.
R Check theva lve caps.
R Visual check of the tyre tread dep thand the
tyre contact sur face across the entire width.
The minimum tread dep thfor summer tyres is
3 mm and for winter tyres 4 mm. N
No
ot
tes on sno
es on sno w c
w chains
hains &
W
WARNING
ARNING Risk of accident due toincor-
re ctly /tted snow chains
If yo u ha ve/tted snow chains tothe front
wheels, they may drag against theve hicle
body or chassis components. #
Never /t snow chains tothe front
wheels. #
Only /t snow chains on there ar wheels
in pairs. Wheels and tyres
411
411