2021 MERCEDES-BENZ CLA COUPE light

R
if operating conditions change, e.g. o.-
ro ad driving #
Adjust the tyre pressure, if necessar y.Ty
re pressure which is too high or too low can:
R Shor tenth e service life of the tyres.
R Cause increased tyre damage.
R Adve rsely a.ect driving characteristics and
th us driving saf ety, e.g. due toaquaplaning. &
W
WARNING
ARNING Risk of accident due torepea-
te d pressure drop in the tyres
The wheels, valves or tyres could be damaged.
To o low a tyre pressure can lead tothe tyres
bursting. #
Examine the tyres forfo re ign objects. #
Check whe ther the tyre has a puncture
or theva lve has a leak. #
Ifyo u are unable torectify the damage,
contact a quali/ed specialist workshop. Information on
there commended tyre pressure
fo rth eve hicle's factor y-/tted tyres can be found
on the tyre pressure table on the inside of the fuel
/ller 0ap (/ page 367).
Use a suitable pressure gauge tocheck the tyre
pressure. The outer appearance of a tyre does not
permit any reliable conclusion about the tyre pres-
sure.
Only cor rect tyre pressures when the tyres are
cold. Conditions for cold tyres:
R The vehicle has been par ked with the tyres out
of direct sunlight for at least thre e hours.
R The vehicle has tr avelled less than 1.6 km.
The vehicle's tyres heat up when driving. As the
te mp erature of the tyres increases, so too does
th e tyre pressure.
V
V ehicles wit ehicles wit h a tyr
h a tyre pr
e pr essur
essur e monit
e monit or
oring syst
ing syst em:
em:
yo u can also check the tyre pressure using the
on-board computer.
Not Not es on tr
es on tr ailer oper
ailer oper ation
ation
Alw ays in0ate there ar axle tyres tothere com-
mended tyre pressures on the tyre pressure table
fo r increased load. T
T
yr
yr e pr
e pr essur
essur e t
e table
able The tyre pressure
table is on the inside of the fuel
/ller 0ap. The tyre pressure
table sho ws there commended
tyre pressure for all tyres appr ovedfo rth is vehi-
cle. The recommended tyre pressures apply for
cold tyres under various operating conditions, i.e.
loading and/or speed of theve hicle. Wheels and tyres
367
367

If one or more tyre sizes precede a tyre pressure,
th efo llowing tyre pressure information is only
va lid forth ose tyre sizes and their respecti veload
condition.
If th e preceding tyre sizes are complemented by
th e+ symbol, the tyre pressure information
fo llowing sho wsalternative tyre pressures. Fuel
consum ption may then increase slightl y.
The load conditions "pa rtially laden" and "fully
laden" are de/ned in theta ble for di.erent num-
bers of passengers and amounts of luggage. The
actual number of seats may di.er from this. T T
yr
yr e pr
e pr essur
essur e monit
e monit or
oring syst
ing syst em
em F
F
unction of t
unction of t he tyr
he tyre pr
e pressur
essur e monit
e monit or
oring syst
ing syst em
em
The system checks the tyre pressure and the tyre
te mp erature of the tyres /t tedtotheve hicle by
means of a tyre pressure sensor.
The tyre pressure and the tyre temp erature
appear in the on-board computer (/ page 368).
If th ere is a substantial pressure loss or if the tyre
te mp erature is excessive, you will be warned with
display messages (/ page 459) ortheh wa
rning lamp in the inst rument cluster
(/ page 483).
The tyre pressure monitoring system is only an
aid. It is the driver's responsibility toset the tyre
pressure tothere commended cold tyre pressure
suitable forth e operating situation.
In most cases, the tyre pressure monitoring sys-
te m will automatically update the new refere nce
va lues aTer you ha vechanged the tyre pressure.
Yo u can, ho wever, also update there fere nce val-
ues byrestarting the tyre pressure monitoring
system manually (/ page 369).
Syst
Syst em limits em limits
The system may be impaired or may not function
particular lyin thefo llowing situations:
R incor rect refere nce values were ta ught in
R sudden pressure loss caused byafo re ign
object penetrating the tyre, forex ample
R there is a malfunction caused byano ther radio
signal source Chec
Chec king t
king t he tyr
he tyr e pr
e pressur
essur e wit
e with t
h the tyr
he tyr e pr
e pressure
essure
monit
monit or
oring sy
ing sy st
stem
em
R
R eq
eq uir
uir ements:
ements:
R The vehicle is switched on.
On-board computer: 4 Service 5
Tyres
One of thefo llowing displa ysappears:
R Current tyre pressure and tyre temp erature of
th e individual wheels: R
Tyre pressures will be displayed after a few
minutes of driving 368 368
Wheels and tyres

#
Pull /ller hose 1and plug 3out of the tyre
in0ation compressor housing. #
Insert plug 7of /ller hose 1inthe soc ket
on the tyre in0ation compressor and then turn
it until plug 7engages. #
Unscr ewthe cap from theva lve on the emer-
ge ncy spa rewheel. #
Screw union nut 2of /ller hose 1onto the
va lve. #
Make sure on and o. switch 4ofthe tyre
in0ation compressor is set to 00. #
Insert plug 3in a soc ket in your vehicle.
R Cigar ette lighter soc ket R
12 V soc ket (/ page 125)
R Obser vethe no tes on the cigar ette lighter in
th e Digital Owner's Manual
R Obser vethe no tes on soc kets (/ page 125). #
Press the start/s top button once toswitch on
th e po wer supply (/ page 159). #
Press on and o. switch 4onthe tyre in0a-
tion compressor to II.
The tyre in0a tion compressor is switched on.
The tyre is in0ated. The tyre pressure is shown
on manom eter 5. #
Pump the tyre tothe speci/ed tyre pressure.
% The speci/ed tyre pressure is stated on the
label of the emer gency spa rewheel. #
When the speci/ed tyre pressure has been
re ached, press on and o. switch 4onthe
tyre in0ation compressor to 00.
The tyre in0a tion compressor is switched o.. #
Press the start/s top button toswitch o. the
po we r suppl y. #
Ifth e tyre pressure is higher than the speci/ed
pressure, press pressure release valve button 6
until the cor rect tyre pressure has been
re ached. #
Unscr ewunion nut 2of /ller hose 1from
th eva lve. #
Screw theva lve cap of the emer gency spa re
wheel onto theva lve again. #
Stow /ller hose 1and plug 3inthe lo wer
section of the tyre in0ation compressor hous-
ing. #
Stow the tyre in0ation compressor in theve hi-
cle. 382 382
Wheels and tyres

Information on coolant is
available at thefo l-
lowing locations:
R Inthe Mercedes-Benz Speci/cation for
Operating Fluids 320.1
- Athttps://be vo.mercedes-benz.com
- Inthe Mercedes-Benz BeVo App
R Ataqu ali/ed specialist workshop *
N NOOTE TE Overheating at high outside temp er-
atures If an inappropriate coolant is used,
the engine
cooling system is not su1ciently pr otected
against overheating and cor rosion at high out-
side temp eratures. #
Only use coolant appr ovedby Mercedes-
Benz. #
Obser vethe inst ructions in the
Mercedes-Benz Speci/cations for Oper-
ating Fluids 320.1. Ha
ve the coolant regula rly re placed at a quali/ed
specialist workshop. Proportion of antif
reeze concentrate in the engine
cooling system:
R A minimum of 50% (antifreeze pr otection down
to about -37°C)
R A maximum of 55% (antif reeze pr otection
down to-45°C) N
No ot
tes on windscr
es on windscr een w
een washer
asher 0uid
0uid Obser
vethe no tes on operating 0uids
(/ page 387). &
W
WARNING
ARNING ‑ Risk of /re and injury due to
windscreen washer concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. It could ignite if it comes into contact
with hot engine component parts or the
ex haust system. #
Make sure that no windscreen washer
concent rate spills out next tothe /ller
opening. *
N NOOTE
TE Damage totheex terior lighting due
to unsuitable windscreen washer 0uid Unsuitable windscreen
washer 0uids may
damage the plastic sur face of theex terior
lighting. #
Only use windscreen washer 0uids which
are also suitable for use on plastic sur fa-
ces, e.g. MB SummerFit or MB WinterFit. *
N
NOOTE
TE Bloc ked spr aynozzles caused by
mixing windscreen washer 0uids #
Do not mix MB SummerFit and MB Win-
te rFit with other windscreen washer 0u-
ids. Do not use distilled or de-ionised
water. Other-
wise, the /ll le vel sensor may be triggered er rone-
ous ly.
Re commended windscreen washer 0uid:
R abo vefreezing point: e.g. MB SummerFit
R below freezing point: e.g. MB WinterFit 396
396
Te
ch nical data

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences andM
MSolutions
Solutions
Place the key in the
marked space See Owner's
Manual *K
eydetection is malfunctioning. #
Change the location of theke y in theve hicle. #
Place theke y in the slot for starting the engine with theke y (/ page 160). Lights Lights
Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/conseq uences and
uences andM
MSolutions
Solutions
:
Left dipped beam (examp le) *T
he cor responding light source is defecti ve. #
Drive on carefull y. #
Consult a quali/ed specialist workshop immediatel y.
or #
Check whe ther you are permitted toreplace the light source yourself (/ page 140).
% LED light sources: the display message forth e cor responding light appears only when all the light-emitting diodes
in the light are faulty. Display message
s andwarning/indicator lamps
409
409

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences andM
MSolutions
Solutions
:
Malfunction See Owner's
Manual *T
heexterior lighting is malfunctioning. #
Consult a quali/ed specialist workshop.
*V Vehicles wit ehicles wit h a tr
h a trailer hitc
ailer hitc h:
h:a fuse may ha veblown. #
Stop theve hicle in accordance with the tra1c conditions. #
Check the fuses and replace them if necessary (/ page 362).
:
Automatic driving lights
inoperative *T
he light sensor for automatic driving lights is malfunctioning. #
Consult a quali/ed specialist workshop.
:
Active Light System inoper-
ative *T
he active headlamps are malfunctioning. #
Consult a quali/ed specialist workshop. 410 410
Displ
aymessages and warning/indicator lamps

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences andM
MSolutions
Solutions
:
Switch on headlamps *Y
ou are driving without lo w-beam headlamps. #
Turn the light switch totheL orà position.
:
Switch off lights *Y
ou are leaving theve hicle and the lights are still switched on. #
Turn the light switch totheà position.
:
Intelligent Light System
inoperative *T
he Intelli gent Light System is malfunctioning. The lighting system continues tofunction proper lywithout the functions
of the Intelligent Light System. #
Consult a quali/ed specialist workshop.
Adaptive Highbeam Assist
currently unavailable See
Owner's Manual *A
daptive Highbeam Assist is tempo rarilyuna vailable.
The system limits ha vebeen reached (/ page 135).
Once the cause of the problem is no longer present, the system will be available again. The Adaptive Highbeam
Assist available again displaymessage will appear. #
Drive on Display messages and
warning/indicator lamps
411
411

Displa
Displa
y messag
y messag es P
es Possible causes/conseq
ossible causes/consequences and uences andM
MSolutions
Solutions
Ù
Steering malfunction See
Owner's Manual *T
he elect ric steering lock is malfunctioning. The steering may be loc kedby the electric steering loc k. &
W WARNI NG
ARNI NGRisk of accident if steering capability is impai red
If th e steering does not function as intended, theve hicle's operating saf ety is jeopardised. #
Pull over and stop theve hicle safely as soon as possible, paying attention toroad and tra1c conditions. Do
not continue driving under any circums tances. #
Consult a quali/ed speciali stwo rkshop. #
Stop theve hicle immediately in accordance with the tra1c conditions. Do not continue driving. #
Consult a quali/ed specialist workshop.
û
Before starting the engine,
turn the steering wheel. *T
he elect ric steering lock could not unlock the steering. #
Switch o. theve hicle. #
Tounlock the steering, mo vethe steering wheel slightly tothe leT and right. #
Switch on theve hicle again.
Active bonnet malfunction
See Owner's Manual *T
he active bonn et(pedest rian pr otection) is malfunctioning or inoperative aTer having already been triggered. #
Consult a quali/ed specialist workshop. Displ
aymessages and warning/indicator lamps
425 425