2021 MERCEDES-BENZ CLA COUPE light

R
Frequent operation in mountainous terrain or
on poor road sur faces
R When the engine is oTen leT idling for long
periods
R Operation in particular lydusty conditions
and/or if air-recirculation mode is frequently
used
In these or similar operating conditions, ha vethe
interior air /lter, air /lter, engine oil and oil /lter,
fo rex ample, changed more frequentl y.The tyres
must be checked more frequently if theve hicle is
operated under increased loads. Further informa-
tion can be obtained at a quali/ed specialist work-
shop. Batt Batt
er
ery disconnection per
y disconnection per iods
iodsThe AS
SYST PLUS service inter val display can cal-
culate the service due date only when the battery
is connected. #
Display and no tedown the service due date
on the inst rument display before disconnect-
ing the battery (/ page 327). Engine com
Engine com
par
partment
tment A
A
ctiv
ctiv e bonne
e bonne t (pedes
t (pedestr trian pr ot
ian pr otection)
ection) Oper
Oper
ation of t
ation of t he activ
he active bonne
e bonne t (pedes
t (pedestr trian pr ot
ian pr otec-
ec-
tion)
tion)
In cer tain accident situations, the actuation of the
active bonnet reduces therisk of injury topedes-
trians. The rear area of the bonnet is raised by
appr oximately 70 mm.
Fo rth e drive tothewo rkshop, reset the actuated
active bonnet yourself (/ page 328).
ATer the active bonnet has been actuated, pedes-
trian pr otection may be limited.
Ha ve the full functionality of the active bonnet
re stored in a quali/ed specialist workshop.
R
R ese ese tting t
tting t he activ
he activ e bonnet
e bonnet &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. #
With your hand 0at, push down active bonnet
1 inthe area around the hinges on bo th
sides (ar rows ).
In doing so, the actuator is depressurised and
yo u may hear a hissing sound.
The engine bonnet must engage in position. #
Ifth e active bonnet can be raised slightly at
th ere ar in the area of the hinges, repeat the
step until it engages co rrectl y. 328
328
Maintenance and care

#
Ifth e bonnet can still be liTed slightl y,open
th e bonnet again and close it with a little force
until it engages cor rectl y. Engine oil
Engine oil
Chec
Chec
king t
king t he engine oil lev
he engine oil lev el using t
el using the on-board
he on-board
com
com put
puter
er
R
R eq
eq uir
uir ements:
ements:
R The engine has been warmed up.
R The vehicle is par ked on a le vel sur face.
R The engine is running at idle speed.
R The bonnet is closed.
The engine oil le vel is de term ined during driving.
De term ining the engine oil le vel can take up to
30 minutes with a normal driving style and even
longer with an active driving style. On-board computer:
4 Service 5
Engine oil level
One of thefo llowing message s will appear onthe
inst rument displa y:
R Engine oil level Measuring now: measu rement
of the oil le vel is not yet possible. #
Repeat there qu est aTer a maximum of
30 minutes' driving.
R Engine oil level OK andthe bar display for
indicating the oil le vel on the inst rument dis-
play is green and is between "min" and "max":
th e oil le vel is cor rect.
R Engine oil level Add 1,0 l andthe bar display
fo r indicating the oil le vel on the inst rument
display is orange and is below "min": #
Add 1 l of engine oil.
R Reduce engine oil level andthe bar display for
indicating the oil le vel on the inst rument dis-
play is orange and is abo ve"max": #
Drain o. any excess engine oil that has been
added. Todo so, consult a quali/ed specialist
wo rkshop.
R For engine oil level turn on ignition #
Switch on theve hicle tocheck the engine oil
le ve l.
R Engine oil level System inoperative: The oil
leve l sensor is defective or not connected. #
Consult a quali/ed specialist workshop.
R Engine oil level System currently unavail. #
Close the bonnet.
T T opping up engine oil
opping up engine oil &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. Maintenance and care
331
331

To
avo id damage toyour vehicle, obser vethefo l-
lowing when using a high-pressure cleaner:
R The key is at a minimum dis tance of 3 m away
from theve hicle. Otherwise the boot lid could
open unintentionall y.
R Maintain a distance of at least 30 cm tothe
ve hicle.
R V
Vehicles wit
ehicles with decor h decorativ
ative f
e foil:
oil: Parts of your
ve hicle are co vered with a decorative foil.
Maintain a distance of at least 70 cm between
th efo il-co vered parts of theve hicle and the
nozzle of the high-pressure cleaner. Mo vethe
high-pressure cleaner nozzle around whilst
cleaning. The waterte mp erature of the high-
pressure cleaner must not exceed 60°C.
R Obser vethe information on the cor rect dis-
ta nce in the equipment manufacturer's oper-
ating inst ructions.
R Do not direct the nozzle of the high-pressure
cleaner directly at sensitive parts, such as
tyres, gaps, electrical components, batteries,
light sources and ventilation slits. W W
ashing t
ashing t he v
he vehicle b
ehicle b y hand
y hand *
N
NOOTE
TE Engine damage due towa ter ing ress #
Take care not topoint thewa ter jet
directly towa rdsth e air inlet grille below
th e bonnet. obser
vethe legal requ irements, e.g. in a number
of countries, washing byhand is only permitted in
special lydesignated wash ba ys. #
Use a mild cleaning agent, e.g. car shampoo. #
Washtheve hicle with luk ewarm water using a
soT car sponge. When doing so, do not
ex pose theve hicle todirect sunlight. #
Carefully hose theve hicle o. with water and
dry using a chamois.
% Obser vethe no tes on the care of car parts
(/ page 339). N
No
ot
tes on paintw
es on paintw or
ork/matt
k/matt /nish
/nishpaintw
paintw or
ork care
k care To
avo id damaging the paintwork and inter fering
with the driving assistance systems, please
obser vethefo llowing no tes: P
P
aint
aint
R Insect remains: soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: soak with water and rinse o.
aTer wards.
R Tree resin, oils, fuels and greases: remo veby
ru bbing gently with a clo thsoaked in petro-
leum ether or lighter 0uid.
R Coolant and brake 0uid: remo vewith a damp
clo thand clean water.
R Tar stains: use tarre mo ver.
R Wax: use silicone remo ver.
R Do not attach sti ckers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a quali/ed specialist workshop.
R Remo vedirt immediatel y,where possible.
Matt
Matt /nish
/nish
R Only use care products appr ovedfor
Mercedes-Benz.
R Do not attach stic kers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a qu ali/ed specialist workshop. Main
tenance and ca re
337
337

R
Do not polish theve hicle and light-alloy
wheels.
R Only use car washes that cor respond tothe
latest engineering standards.
R Do not use car wash prog rammes with a /nal
hot wax treatment.
R Do not use paint cleaners, bu1ng or polishing
products, gloss preser vers, e.g. wax.
In theev ent of paintwork damage:
R Always ha vepaintwork repairs car ried out at a
qu ali/ed specialist workshop.
R Make sure thera dar sensors function
(/ page 214). N
No
ot
tes on cleaning decor
es on cleaning decor ativ
ative f
e foils
oils Obser
vethe no tes on matt /nish care in thech ap-
te r "No tes on paintwork/matt /nish paintwork
care" (/ page 337). They also apply tomatt dec-
orative foils.
Obser vethe no tes on cleaning decorative foils to
av oid vehicle damage. Cleaning
Cleaning
R For cleaning, use plenty of water and a mild
cleaning agent without additives or abrasive
substances, e.g. a car shampoo appr ovedfor
Mercedes-Benz.
R Remo vedirt immediatel y,where possible,
whilst avoiding rubbing too hard. There is oth-
erwise a risk of damaging the decorative foil
ir re parabl y.
R Ifth ere is dirt on the /nish or if the decorative
fo il is dull: Use thePa int Cleaner recommen-
ded and appr ovedfo r Mercedes-Benz.
R Insect remains: Soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: Soak with water and rinse o.
aTer wards.
R Topreve ntwa ter stains, dry a foil-wrapped
ve hicle with a soT, absorbent clo thaTer every
car wash.
Av
Av oiding damag
oiding damag e t
e to t
o t he decor
he decor ativ
ative f
e foil
oil
R The service life and colouring of decorative
foils are impaired by:
- Sunlight -
Tempe rature, e.g. hot air blo wer
- Weather conditions
- Stone chippings and dirt
- Chemical cleaning agents
- Oily products
R Do not use polish on matt decorative foil. Po l-
ishing will ha vethe e.ect of shining thefo il-
wrapped sur face.
R Do not treat matt or st ructured decorative
fo ils with wax.Pe rm anent stains may occur.
Scratches, cor rosive deposits, areas a.ected by
cor rosion and damage caused byincor rect care
cannot alw ays be comple tely re paired. In such
cases, visit a quali/ed specialist workshop.
Yo u can obtain more information on care and
cleaning products from the manufacturer.
In the case of foil-wrapped sur faces, optical di.er-
ences may occur between the sur faces that we re
not pro tected bya decorative foil aTer removing a
decorative foil. 338 338
Maintenance and care

Ext
Ext
er
erior lighting
ior lighting
R Clean the lenses with a wet sponge and mild
cleaning agent, e.g. car sha mpoo.
R Only use cleaning agents or cleaning clo ths
th at are suitable for plastic lenses.
V
V ehicle soc ke
ehicle soc ket (high-v
t (high-v olt
oltag
age batt
e batt er
ery)
y)
R Use clean water and a soT clo thtoclean the
ve hicle soc ket.
R Do not use high-pressure cleaners or cleaning
agents, such as soap.
Sensors Sensors
R Clean the sensors in the front and rear bump-
ers with a soT clo thand car shampoo
(/ page 214).
R When using a high-pressure cleaner, main tain
a minimum distance of 30 cm.
Rev
Rev er
ersing camer
sing camer a and 360° Camera
a and 360° Camera
R Open the camera co ver with the multimedia
system (/ page 254).
R Use clean water and a soT clo thtoclean the
camera lens.
R Do not use a high-pressure cleane r.T
T
ailpipes
ailpipes
R Clean with a cleaning agent recommended for
Mercedes-Benz, especially in the winter and
aTer washing theve hicle.
R Do not use acidic cleaning agents.
Tr
Tr ailer hitch
ailer hitch
R Obser vethe no tes on care in the trailer hitch
manufacturer's operator manual.
R Do not clean the ball neck with a high-pres-
sure cleaner or sol vent.
R Remo vetraces of rust on the ball, forex ample,
with a wire brush.
R Remo vedirt with a lint-free clo th.
R ATer cleaning, lightly oil or grease the ball
head.
% Before using trailers with anti-torsional cou-
pling, obser vethe manufacturer's operator
manual. N No
ot
tes on car
es on car e of t
e of the int
he int er
erior
ior &
W
WARNING
ARNING Risk of injury from plastic parts
breaking o. aTer the use of sol vent-based
ca re products
Care and cleaning products containing sol-
ve nts can cause sur faces in the cockpit to
become porous. When the airbags are
deplo yed, plastic parts may break away. #
Do not use any care or cleaning products
containing sol vents toclean the cockpit. &
W WARNING
ARNING Risk of injury or fatal injuries
from bleached seat belts
Bleaching or dyeing seat belts can se verely
we aken them.
This can, forex ample, cause seat belts to tear
or fail in an accident. #
Never bleach or dye seat belts. To
avo id damage totheve hicle, obser vethefo l-
lowing no tes on cleaning and care: 340
340
Main
tenance and ca re

Seat belts
Seat belts
R Clean wi thluk ewa rmand soapy water.
R Do not use chemical cleaning agents.
R Do not dry byheating them toove r 80°C or
ex posing them todirect sunlight.
Display
Display
R Switch o. the display and let it cool down.
R Clean the sur face carefully with a micro/bre
clo thand a suitable displ aycare product (TFT-
LC D).
R Do not use any other agents.
Head-up displ ay
Head-up display
R Clean with a soT, non-static, lint-free clo th.
R Do not use cleaning agents.
Plas
Plastic tr tic tr im
im
R Clean with a damp micro/bre clo th.
R For heavy soiling: Use a cleaner recommen-
ded for Mercedes-Benz.
R Do not attach stic kers, /lms or similar materi-
als. R
Do not allow cosmetics, insect repellent or
sun cream tocome in contact with the plastic
trim.
R
R eal w
eal w ood and tr
ood and tr im elements
im elements
R Clean with a micro/bre clo th.
R Blackpiano-lacquer look: Clean with a damp
clo thand soapy water.
R For heavy soiling: Use a cleaner recommen-
ded for Mercedes-Benz.
R Do not use sol vent-based cleaning agents, pol-
ishes or waxes.
R
R oof lining
oof lining
R Clean with a brush or dry shampoo.
Car
Car pet
pet
R Use a carpet and textile cleaning agent recom-
mended for Mercedes-Benz.
St
St eer
eer ing wheel made of g
ing wheel made of g enuine leat
enuine leat her or DINA-
her or DINA-
MICA
MICA
* NO
NOTE
TEDamage caused bywrong cleaners #
Do not use sol vent-based cleaning
agents such as tarre mo ver or wheel cleaner; neither should
you use polishes
or wa xes. Otherwise you may damage
th e /nish. R
Clean with a damp clo thand 1% soapy water
solution and then wipe with a dry clo th.
R For heavy soiling: Use a cleaner recommen-
ded for Mercedes-Benz.
R Leather care: Use a leather care agent that
has been recommended for Mercedes-Benz.
R Do not allow the leather tobecome too damp.
R Do not use a micro/bre clo th.
% Leather is a natural product. It has natural
surface properties, such as di.erences in
st ru cture, mar kscaused bygrow thand injury
or subtle colour di.erences. These sur face
properties are characteristics of leather and
not material faults. What's more, leather is
subject toa natural ageing process during
which the sur face properties change.
Genuine leat
Genuine leat her seat cov her seat covers
ers
R Clean with a damp clo thand then wipe with a
dry clo th. Maintenance and ca
re
341
341

#
Take care toonly connect battery term i-
nals of identical polarity when receiving
starting assistance. #
Obser vethe sequence described for
connecting and disconnecting the jump
leads when receiving starting assistance. #
Do not connect or disconnect the bat-
te ry term inals while the engine is run-
ning. &
W
W ARNI NG
ARNI NGRisk of explosion due toexplo-
sive mixture of gases
An explosive mixture of gases can escape
from the battery during charging and starting
assis tance. #
Fire , naked 0ames, smoking and creating
spar ksmust be avoided. #
Make sure there is adequate ventilation. #
Do not stand overth e batter y. &
W
WARNI NG
ARNI NGRisk of explosion from a frozen
battery
A dischar ged battery may freeze at temp era-
tures slightly abo veor below freezing point.
During starting assistance or battery charging,
battery gas can be released. #
Always allow a battery tothaw before
ch arging it or per form ing starting assis-
ta nce. If
th e indicator/warning lamps in the inst rument
clus ter do not light up at low temp eratures, it is
ve ry likely that the dischar ged battery has frozen.
In this case you may neither jump-start theve hi-
cle nor charge the batter y.
The service life of a bat tery that has been thawed
may be dramatically shor tened. The starting char-
acteristics may be impaired, especially at low
te mp eratures.
It is recommended that you ha veath awe d battery
ch ecked at a quali/ed specialist workshop. Plug-in h
Plug-in h ybr
ybrid
id
If yo ur vehicle has been star ted with starting
assistance, it may not be possible touse the elec-
tric drive for appr oximately 30 minutes.
St arting assis tance is not considered tobe a nor-
mal operating condition.
All v All v ehicles
ehicles
* NO
NOTE
TEDamage caused bynume rous or
ex tended attem ptsto start the engine Numerous or
extended attem ptsto start the
engine may damage the catalytic con verter
due tonon-combusted fuel. #
Avoid numerous and extended attem pts
to start the engine. Obser
vethefo llowing points during starting assis-
ta nce and when charging the batter y:
R Only use undamaged jump lead/charging
cables with a su1cient cross-section and
insulated term inal clamps.
R Non-insulated parts of thete rm inal clamps
must not come into contact with other me tal Breakd
own assistance
353 353

begin with POSITIVE contact
2onyour own
ve hicle /rst. #
Dur
During st
ing st ar
arting assist
ting assist ance:
ance:startthe engine of
th e donor vehicle and run at idle speed. #
Connect the negative term inal of the donor
battery and ear thpoint 3ofyour ow nve hicle
by using the jump lead/charging cable. Begin
with the donor battery /rst. #
Dur
During st
ing st ar
arting assist
ting assist ance:
ance:startthe engine of
yo ur ow nve hicle. #
Dur
During t
ing t he c
he char
harging pr
ging pr ocess:
ocess: startthech arg-
ing process. #
Dur
During st
ing st ar
arting assist
ting assist ance:
ance:letthe engines run
fo r se veral minutes. #
Dur
During st
ing st ar
arting assist
ting assist ance:
ance:before disconnect-
ing the jump lead, switch on an electrical con-
sumer on your ow nve hicle, e.g. there ar win-
dow heater or lighting.
When the starting assistance/charging process is
comple te, per form thefo llowing steps: #
Firs t, re mo vethe jump lead/charging cable
from ear thpoint 3and the negative term inal of
the donor batter y,then POSITIVE contact
2 and the positive term inal of the donor bat-
te ry. Begin each time with the contacts on
yo ur ow nve hicle /rst. #
ATer removing the jump lead/charging cable,
close co ver1 of POSITIVE contact 2.
Plug-in h
Plug-in h ybr
ybrid:
id:ifyo ur vehicle has been star ted
with starting assis tance, it may not be possible to
use the electric drive for appr oximately 30
minutes.
Fu rther information can be obtained at a quali/ed
specialist workshop. R R
eplacing t
eplacing t he 12 V batt
he 12 V batt ery
ery #
Obser vethe no tes on the 12 V battery
(/ page 350).
Mercedes-Benz recommends that you ha vethe
12 V battery replaced at a quali/ed specialist
wo rkshop, e.g. at a Mercedes-Benz Se rvice
Centre. Obser
vethefo llowing no tes if youwa nttoreplace
th e battery yourself:
R Alwaysre place a faulty battery with a battery
which meets the speci/c vehicle requ ire-
ments.
The vehicle is equipped with an AGMtech nol-
ogy bat tery (Absorbent Glass Mat) or a lith-
ium-ion batter y.Fu llve hicle functionality is
only guaranteed with an AGM bat tery or lith-
ium-ion batter y.Fo r saf etyre asons, Mercedes-
Benz recommends that you only use batteries
which ha vebeen tested and appro vedfo ryo ur
ve hicle byMercedes-Benz.
R Carryove r de tach able parts, such as vent
hoses, elbow /ttings or term inal co vers from
th e battery being replaced.
R Make sure that theve nt hose is alw ays con-
nected tothe original opening on the side of
th e batter y.
Fi t any existing or supplied cell caps.
Otherwise, gases or battery acid could
escape.
R Make sure that de tach able parts are recon-
nected in the same way. Breakd
own assistance
355 355