2021 MERCEDES-BENZ A-CLASS SALOON battery

%
When using a CCS (Combined Charging Sys-
te m) charging cable tocharge with direct cur-
re nt at a combo vehicle soc ket, bo thvehicle
soc ket connections 1and 2are used for
ch arging.
Charging options forth e high-voltage battery
(mode 2, 3 or 4):
R Charging through recuperation while theve hi-
cle is in motion
R Charging with alternating cur rent when sta-
tiona ry:
- at a mains soc ket (mode 2)
- at a wallbox or charging station (mode 3)
R Charging with direct cur rent when stationary
(vehicles with combo vehicle soc kets):
- at a fast charging station (mode 4)
Depending on the count ry-speci/c vehicle equip-
ment and your vehicle's charging cable, single
phase ACcharging is also possible.
Obser vethe di.erent grid requ irements of your
cur rent location when charging. Only use charging
cables which conform tothegr id requiremen ts.Consult a
quali/ed elect rician or your local grid
operator if you ha veany questions.
It is recommended that youch arge the high-volt-
age battery at a wallbox or charging station due to
th e impr ovedch arging per form ance and better
ch arging e1ciency o.ered.
S
S t
to
o wing t
wing t he c
he char
harging cable
ging cable
Alw ays st owtheve hicle charging cable in the
ch arging cable bag pr ovided and secure it in the
boot or load compartment of your vehicle.
Otherwise, thech arging cable is not su1ciently
secured.
Syst Syst em limits
em limits
The po wer output of the high-voltage battery may
be impaired bythefo llowing:
R High or low outside temp eratures
R Electrical auxiliary consumers in theve hicle
being switched on, e.g. operating the air con-
ditioning system
R Extended periods without charging The
charging time of the high-voltage battery may
be increased bythefo llowing:
R High or low outside tempe ratures
R Extended periods without charging
R The maximum available charge cur rent of the
ch arging facility
R The charging cur rent set (mode 2) in the multi-
media system (/ page 292) N
No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at t
y at t he
he
mains soc ke
mains soc ket (mode 2)
t (mode 2) &
D
DAN
AN GER
GER Risk of fatal injury from incor-
re ctly ins talled component parts
Connecting thech arging cable toa mains
soc ket using incor rectly ins talled component
parts could cause a /re or an electric shoc k,
fo rex ample. #
Only connect thech arging cable to a
mains soc ketth at:
R Has been proper lyinstalled and 190
190
Driving and parking

R
Has been inspec tedby aqu ali/ed elect ri-
cian #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable. #
Purchase these parts at a Mercedes-
Benz Service Centre and obtain advice
th ere.
Mercedes-Benz thoroughly tests these original
ch arging cables forth eir suitability for high-
vo ltage charging of your vehicle. #
Never use a damaged charging cable. #
Do not use:
R Extension cables
R Extension reels
R Multiple soc kets #
Never use soc ket ada pters toconnect
th ech arging cable tothe mains soc ket.
The only exception being if the adap ter
has been tested and appro vedby the manufacturer
forch arging the high-volt-
age battery of an electric vehicle. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth e soc ket ada pter. Only
thefo llowing charging cables may be used:
R The charging cable supplied with theve hicle.
R Ach arging cable that has been appr ovedfor
th eve hicle.
The charging process can vary depending on the
po we r supply equipment.
Shor terch arging times can be achie ved in thefo l-
lowing ways:
R Charging at a wallbox.
R Charging at a charging station.
When doing so, alw ays obser vethe local informa-
tion.
Do not lea vethech arging cable cont rols hanging
loose from a mains soc ket. Do not liT
the controls bythefo llowing compo-
nent parts:
R The charging cable connector.
R The mains plug.
When charging, pr otect thech arging cable cont rol
element from excessive heat such as direct sun-
light. Otherwise, thech arging process may be
cancelled. N No
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
oltag
age batt
e batt er
ery at a
y at a
w
w allbo
allbo x or c
x or c har
har ging st
ging st ation (mode 3)
ation (mode 3) &
D
DAN
AN GER
GER Risk of fatal injury from incor-
re ctly ins talled component parts
Connecting thech arging cable toawa llbox
using incor rectly ins talled component parts
could cause a /re or an electric shoc k,for
ex ample. #
Only connect thech arging cable to a
wa llbox that:
R Has been proper lyinstalled and Driving and parking
191
191

R
Has been inspec tedby aqu ali/ed elect ri-
cian #
For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer forch arg-
ing the high-voltage battery in an electric
ve hicle. #
Never use damaged charging cables. #
Do not extend thech arging cable. #
Do not use adap ters. #
Obser vethe saf ety no tes in the operat-
ing inst ructions forth ewa llbox. If
ch arging at a wallbox without pre-ins talled
cable, use the optionally available charging cable
fo rwa llbox and charging station (mode 3). The
ch arging cable is st owed in a bag in the boot/
luggage compartment.
Only use charging cables that ha vebeen tested
and appro vedby the manufacturer forch arging
th e high-voltage battery in an electric vehicle. &
D DAN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable.
R Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The amount of ene rgy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when
ch arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. 192
192
Driving and parking

N
N
o
ot
tes on c
es on c har
harging t
ging t he high-v
he high-v olt
olt ag
age batt
e batt er
ery at a
y at a
f
f as
ast c t c har
har ging st
ging st ation (mode 4)
ation (mode 4) &
D
D AN
AN GER
GER Risk of fatal injuries due todam-
aged components
Connecting thech arging cable toach arging
station using a damaged component part
could cause a /re or an elect ric shoc k,for
ex ample. #
Forch arging stations with a preinstalled
ch arging cable:
R Perform a visual check of thech arg-
ing station for obvious faults, such as
massive damage tothe housing or
ch arging cable. #
Forch arging stations without a preinstal-
led charging cable:
R For saf etyre asons, only use charging
cables that ha vebeen tested and
appro vedby the manufacturer for
ch arging the high-voltage battery in
an electric vehicle.
R Never use damaged charging cables.
R Do not extend thech arging cable. R
Do not use adap ters. #
Make sure toobser vethe saf ety in form a-
tion on thech arging station. Most
charging stations must be activated before
th ech arging process, e.g. using an RFID card.
Obser vethe on-site operator's inst ructions forthe
ch arging station.
The charging cable forth eve hicle must not be
lon gerth an 30 m due tothe legal requ irements in
some countries. This is toprev ent the inter fer-
ence of signals being received byradio communi-
cation devices in theve hicle or in close pr oximity
to thech arging station. Be awarethat parts of the
ch arging cable may be routed under ground. If in
doubt, ask thech arging station operator if this is
th e case before charging the high-voltage batter y.
The amount of energy dispensed forth ech arging
process, shown bythech arging station, may be
higher than the amount of energy actually absor-
bed bythe high-voltage batter y.This is there sult
of di.erent le vels of charging losses and is descri-
bed as rech arge e1ciency. Charging losses occur,
fo rex ample, due toheat that builds up when ch
arging or from auxiliary consumers that are
switched on. Further information on rech arge e1-
ciency can be obtained at a quali/ed specialist
wo rkshop. Se
Se
tting t
tting t he maximum per
he maximum per missible c
missible char
harging cur-
ging cur-
r
r ent f
ent f or c
or char
harging at a mains soc ket
ging at a mains soc ket *
N
NO
OTE
TE Overloading the mains soc ket due
to excessive charging cur rent If
th ech arging cur rent is too high, the fuse
could be tripped or theex tern al mains supply
could overheat. #
Make sure that theex tern al mains supply
has been designed tohandle the set
ch arging cur rent. #
If necessar y,reduce the set charging
cur rent or use a di.erent mains soc ket. #
For saf etyre asons, only use thech arging
cable supplied with theve hicle or an
original Mercedes-Benz charging cable.
Mercedes-Benz thoroughly tests these
original charging cables forth eir suitabil- Driving and parking
193
193

Combo 2
vehicle soc ket #
Press the centre rear section of soc ket 0ap
1 and swing the soc ket 0ap forw ards and
open.
The % indicator lamp 2and status dis-
play 3light up white. %
When theve hicle is switched on (the õ
displ ayis lit in the Instrument Display), soc ket
0ap 1cannot be opened. #
Press cat ch7 tothe leT and fold open
soc ket co ver5.
% Vehicles with a vehicle soc ket combo requ ire
only connection 8forth ech arging cable
connector. Open only the upper part of soc ket
co ver5. #
Tocharge at a mains soc ket, insert the mains
plug into the mains soc ket of theex tern al
po we r source tothe stop and set the maxi-
mum charging cur rent if requ ired
(/ page 193). #
Insert thech arging cable connector into vehi-
cle soc ket connection 8tothe stop. If the
wa llbox/charging station is not equipped with
a ch arging cable, inse rtthe plug of theve hi-
cle's charging cable into thewa llbox/charging
station soc ketto the stop.
Make sure that thech arging cable is not taut
when inser ted. The
# indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d.
% Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as
needed or when electrical consumers are
activated (e.g. the pre-entry climate control). Driving and parking
199 199

Combo 1
vehicle soc ket Combo 2
vehicle soc ket #
Press the centre rear section of soc ket 0ap
1 and swing the soc ket 0ap forw ards and
open.
The % indicator lamp 2and status dis-
play 3light up white. %
When theve hicle is switched on (the õ
displ ayis lit in the Instrument Display), soc ket
0ap 1cannot be opened. #
Press cat ch7 tothe leT and fold open
soc ket co ver5.
% The CCS charging cable connector requ ires
connections 6and 8. Therefore, it is nec-
essary toopen bo thparts of soc ket co ver5. #
Insert the CCS charging cable connector into
th eve hicle soc ketto the stop.
Make sure that thech arging cable is not taut
when inser ted.
The # indicator lamp 4and status dis-
play 30ash orange and, as soon as the high-
vo ltage battery is charge d, green.
When thech arging cable is connected totheve hi-
cle, theve hicle cann otbe star ted or mo ved.
At the start of thech arging process, thech arge
le ve l display is shown in the Instrument Display
with a charging prediction. The charging predic-
tion either refers to the predicted charge leve l at
th e set departure time, or the time at which the
high- voltage battery will be fully charge d. Driving and parking
203 203

%
Depending on thete mp erature, thefa n and
bat tery cooling system may audibly switch on
during thech arging process.
% Ifth eve hicle is idle for lengt hyperiods and
connected tothe mains suppl y,the high-volt-
age battery will be rech arge d automatically as
needed or when electrical consumers are
activated (e.g. the pre-entry climate control). Ending t Ending t
he dir
he direct curr
ect curr ent c
ent c har
harging pr
ging pr ocess (mode
ocess (mode
4)
4) R
R
eq
eq uir
uir ements:
ements:
R The distance between theke y and theve hicle
does not exceed 1 m. Combo 1 v
Combo 1 v
ehicle socket
ehicle soc ket #
Press charging inter ruption button 3.
The charging process is ended. The %indi-
cator lamp 1lights up white. The vehicle
soc ket is unloc ked. #
Press and hold button 2onthech arging
cable connector and remo vethech arging
cable connector from theve hicle soc ket. %
Ifyo u cannot remo vethech arging cable con-
nector, unlock theve hicle and repeat the pro-
cedure. If thech arging cable connector is still
loc ked, contact a quali/ed specialist work-
shop. #
Close the soc ket co ver and the soc ket 0ap.
Combo 2 v
Combo 2 v ehicle socket
ehicle soc ket 204
204
Driving and parking

%
The electric parking brake is only securely
applied if there d! indicator lamp is lit
continuousl y.
R
R eleasing eleasing #
Switch on theve hicle. #
Pull handle 1.
The red! indicator lamp in the inst rument
clus ter goes out.
Emerg
Emerg ency br
ency br aking
aking #
Press and hold handle 1.
As long as theve hicle is in motion, the
Release parking brake message is displayed
and there d! indicator lamp 0ashes.
When theve hicle has been braked toa stand-
still, the electric parking brake is applied. The
re d! indicator lamp lights up in the inst ru-
ment clus ter. Inf
Inf
or
ormation on collision det
mation on collision det ection on a park
ection on a park ed
ed
v
v ehicle
ehicle If a collision is de
tected when theto w- awa y pro-
te ction is primed on a loc kedve hicle, you will re
ceive a noti/cation in the multimedia system
when you switch theve hicle on.
Yo u will receive information about thefo llowing
points:
R The area of theve hicle that may ha vebeen
damaged.
R The forc e of the impact.
The following situation can lead toinadver tent
activation:
R The par kedve hicle is mo ved, forex ample, in a
two-s tore yga rage.
% Deactivate tow- awa y protection in order to
pr ev ent inadver tent activation. If you deacti-
va te to w-awa y protection, collision de tection
will also be deactivated.
Syst
Syst em limits em limits
De tection may be restric ted in thefo llowing situa-
tions:
R theve hicle is damaged without impact, for
ex ample, if an outside mir ror is torn o. or the
paint is damaged byakey
R an impact occurs at low speed R
the electric parking brake is not applied N No
ot
tes on par
es on par king up t
king up the v
he vehicle
ehicle If
yo u lea vetheve hicle par ked up for longer than
six weeks, it may su.er damage thro ugh disuse.
The 12 V battery may also be impaired or dam-
aged byheavy discharging.
V
V ehicles wit
ehicles wit h aut
h automatic tr
omatic tr ansmission:
ansmission: do not dis-
connect the 12 V battery even if theve hicle is leT
idle for a lengt hyperiod.
% Further information can be obtained at a
qu ali/ed specialist workshop. S
S
t
tandb
andb y mode (e
y mode (e xt
xtension of t
ension of t he st
he start
arter batt
er batt er
ery's
y's
per
per iod out of use)
iod out of use) S
S
t
tandb
andb y mode function
y mode function
% This function is not available for all models.
If standby mode is activated, energy loss will be
minimised during extended periods of non-opera-
tion. 212
212
Driving and parking