2021 MERCEDES-BENZ A-CLASS HATCHBACK engine

R
Electric lines tothe ignition coils and the fuel
injectors &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
W ARNING
ARNING Risk of injury from using the
windscreen wipers when the bonnet is
open
If th e windscreen wipers start moving when
th e bonnet is open, you could be trapped by
th e wiper linkage. #
Always switch o. the windscreen wipers
and theve hicle /r stifyo u need toopen
th e bonnet. Opening t
Opening t
he bonnet
he bonnet #
Torelease the bonnet, pull on handle 1. #
Push yellow handle 1onthe bonnet catch to
th e leT as far as it will go (palm down wards).
LiT the bonnet until it is automatically raised
by the pneumatic spring.
Closing t
Closing t he bonnet
he bonnet #
Lowe rth e bonnet and let it drop from a height
of appr oximately 20 cm. Maintenance and care
333
333

#
Ifth e bonnet can still be liTed slightl y,open
th e bonnet again and close it with a little force
until it engages cor rectl y. Engine oil
Engine oil
Chec
Chec
king t
king t he engine oil lev
he engine oil lev el using t
el using the on-board
he on-board
com
com put
puter
er
R
R eq
eq uir
uir ements:
ements:
R The engine has been warmed up.
R The vehicle is par ked on a le vel sur face.
R The engine is running at idle speed.
R The bonnet is closed.
The engine oil le vel is de term ined during driving.
De term ining the engine oil le vel can take up to
30 minutes with a normal driving style and even
longer with an active driving style. On-board computer:
4 Service 5
Engine oil level
One of thefo llowing message s will appear onthe
inst rument displa y:
R Engine oil level Measuring now: measu rement
of the oil le vel is not yet possible. #
Repeat there qu est aTer a maximum of
30 minutes' driving.
R Engine oil level OK andthe bar display for
indicating the oil le vel on the inst rument dis-
play is green and is between "min" and "max":
th e oil le vel is cor rect.
R Engine oil level Add 1,0 l andthe bar display
fo r indicating the oil le vel on the inst rument
display is orange and is below "min": #
Add 1 l of engine oil.
R Reduce engine oil level andthe bar display for
indicating the oil le vel on the inst rument dis-
play is orange and is abo ve"max": #
Drain o. any excess engine oil that has been
added. Todo so, consult a quali/ed specialist
wo rkshop.
R For engine oil level turn on ignition #
Switch on theve hicle tocheck the engine oil
le ve l.
R Engine oil level System inoperative: The oil
leve l sensor is defective or not connected. #
Consult a quali/ed specialist workshop.
R Engine oil level System currently unavail. #
Close the bonnet.
T T opping up engine oil
opping up engine oil &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. 334
334
Maintenance and care

&
W
W ARNI NG
ARNI NGRisk of /re and injury from
engine oil
If engine oil comes into contact with hot com-
ponent parts in the engine compartment, it
may ignite. #
Make sure that no engine oil is spilled
next tothe /ller opening. #
Allow the engine tocool o. and thor-
oughly clean the engine oil from compo-
nent parts before starting theve hicle. *
N
NO OTE
TE Engine damage caused byan inco r-
re ct oil /lter, incor rect oil or additi ves #
Do not use engine oils or oil /lters which
do not cor respond tothe speci/cations
ex plicitly prescribed forth e service inter-
va ls. #
Follow the inst ructions on the service
inter val display forch anging the engine
oil and obser vethe prescribed change
inter vals. #
Do not use additives. *
N
NOOTE
TE Damage caused bytopping up too
much engine oil To
o much engine oil can damage the engine or
th e catalytic con verter. #
Have excess engine oil remo ved at a
qu ali/ed specialist workshop. %
Depending on driving st yle, theve hicle con-
sumes up to0.8 litre of oil per 1000 km. The
oil consum ption may be higher than this when
th eve hicle is new or if you frequently drive at
high engine speeds. #
Turn cap 1anti-clockwise and remo veit. #
Top up the engine oil. #
Replace cap 1and turn it clockwise until it
engages. #
Check the oil le vel again (/ page 334). Maintenance and care
335
335

Chec
Chec
king t
king t he coolant lev
he coolant lev el
el &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. &
W
WARNING
ARNING Risk of scalding from hot cool-
ant
If yo u open the cap, you could be scalded. #
Let the mo tor cool down before opening
th e cap. #
When opening the cap, wear pr otective
glo ves and saf ety glasses. #
Open the cap slo wlytorelease pressure. #
Park theve hicle on a le vel sur face. #
Check the coolant temp erature display in the
inst rument cluster.
The coolant temp erature must be below 70°C. #
Slowly turn cap 1anti-clockwise torelease
ove rpressure. #
Continue turning cap 1anti-clockwise and
re mo veit. The coolant le
vel is cor rect in thefo llowing cases:
R Ifth e engine is cold, the coolant is up to
mar ker bar 2.
R Ifth e engine is warm,th e coolant is up to
1.5 cm overth e mar ker bar 2. #
If necessar y,top up with coolant that has
been appr ovedfo r Mercedes-Benz.
% Further information on coolant (/ page 401) T
T
opping up t
opping up t he windscr
he windscreen w
een washer syst
asher syst em
em &
W
WARNING
ARNING Risk of burns from hot compo-
nent parts in the engine compartment
Cer tain component parts in the engine com-
partment can be very hot, e.g. the engine, the
cooler and parts of theex haust system. #
Allow the engine tocool down and only
to uch component parts described in the
fo llowing. 336
336
Maintenance and care

&
W
W ARNI NG
ARNI NG‑ Risk of /re and injury due to
windscreen washer concent rate
Wi ndsc reen washer concent rate is highly 0am-
mable. It could ignite if it comes into contact
with hot engine component parts or the
ex haust system. #
Make sure that no windscreen washer
concent rate spills out next tothe /ller
opening. #
Remo vecap 1bytheta b. #
Top up thewa sher 0uid.
% Further information about the windscreen
wa sher 0uid (/ page 402) K K
eeping t
eeping t he air
he air-w
-wat
ater duct fr
er duct fr ee
ee #
Keep the area between the bonnet and the
windscreen free of deposits, e.g. ice, snow
and lea ves. Cleaning and care
Cleaning and care
Inf
Inf
or
ormation on w
mation on w ashing t
ashing the v
he vehicle in a car w
ehicle in a car w ash
ash &
W
WARNING
ARNING Risk of an accident due to
re duced braking po wer aTer washing the
ve hicle
Braking e1ciency is reduced aTer washing the
ve hicle. #
ATer theve hicle has been washed, brake
carefully while paying attention tothe
tra1c conditions until braking po wer has
been fully restored. Maintenance and ca
re
337
337

R
The wind ows and the sliding sunroof are
closed.
R The air conditioning system is set toair-recir-
culation mode.
R Parking Assist PARKTRONIC is deactivated.
R V
Vehicles wit
ehicles wit h 360° Camer
h 360° Camer a:
a:the front image is
activated aTer appr ox. eight seconds.
If one of the settings cannot be selected, this is
displa yedby a% behind there specti veset-
ting.
Ab ove a speed of 20 km/h Car wash mode is
automatically deacti vated.
The following settings are reset when car wash
mode is deacti vated:
R The outside mir rors are folded out.
R The rain sensor is activated.
R The rear wind owwiper is activated.
R The air conditioning system is set tofresh air
mode.
R Parking Assist PARKTRONIC is reset tothe
pr ev iously selected setting. R
The windo wsand the sliding sunroof remain
closed.
R V
V ehicles wit ehicles wit h 360° Camer
h 360° Camer a:
a:the front image is
deactivated at speeds abo ve18 km/h. A
A
ctiv
ctiv ating/deactiv
ating/deactiv ating aut
ating automatic car w
omatic car w ash mode
ash mode R
R
eq
eq uir
uir ements:
ements:
R theve hicle is stationar y.
R the engine is running.
Multimedia system: 4 © 5
Settings 5
Quick access
A
A ctiv
ctiv ating aut
ating aut omatic car w
omatic car w ash mode
ash mode #
Select Car wash mode . #
Select Start.
If one of the settings cannot be selected, this is
displa yedby a% behind there specti veset-
ting.
% For an overview of the settings made when
activating automatic car wash mode
(/ page 337). Deactiv Deactiv
ating aut
ating aut omatic car w
omatic car w ash mode
ash mode #
Select Stop.
The automatic car wash settings are reset.
% The automatic car wash mode is automatically
deacti vated as soon as a speed of 20 km/h is
ex ceeded. Inf
Inf
or
ormation on using a high-pr
mation on using a high-pr essur
essure cleaner
e cleaner &
W WARNING ARNING Risk of an accident when using
high-pressure cleane rswith round-spr ay
nozzles
The water jet can cause extern ally invisible
damage.
Components damaged in this wa y may un ex-
pectedly fail. #
Do not use a high-pressure cleaner with
round-spr aynozzles. #
Have damaged tyres or chassis parts
re placed immediatel y. Maintenance and ca
re
339 339

To
avo id damage toyour vehicle, obser vethefo l-
lowing when using a high-pressure cleaner:
R The key is at a minimum dis tance of 3 m away
from theve hicle. Otherwise theta ilgate could
open unintentionall y.
R Maintain a distance of at least 30 cm tothe
ve hicle.
R V
V ehicles wit
ehicles with decor h decorativ
ative f
e foil:
oil: Parts of your
ve hicle are co vered with a decorative foil.
Maintain a distance of at least 70 cm between
th efo il-co vered parts of theve hicle and the
nozzle of the high-pressure cleaner. Mo vethe
high-pressure cleaner nozzle around whilst
cleaning. The waterte mp erature of the high-
pressure cleaner must not exceed 60°C.
R Obser vethe information on the cor rect dis-
ta nce in the equipment manufacturer's oper-
ating inst ructions.
R Do not direct the nozzle of the high-pressure
cleaner directly at sensitive parts, such as
tyres, gaps, electrical components, batteries,
light sources and ventilation slits. W W
ashing t
ashing t he v
he vehicle b
ehicle b y hand
y hand *
N
NOOTE
TE Engine damage due towa ter ing ress #
Take care not topoint thewa ter jet
directly towa rdsth e air inlet grille below
th e bonnet. obser
vethe legal requ irements, e.g. in a number
of countries, washing byhand is only permitted in
special lydesignated wash ba ys. #
Use a mild cleaning agent, e.g. car shampoo. #
Washtheve hicle with luk ewarm water using a
soT car sponge. When doing so, do not
ex pose theve hicle todirect sunlight. #
Carefully hose theve hicle o. with water and
dry using a chamois.
% Obser vethe no tes on the care of car parts
(/ page 342). N
No
ot
tes on paintw
es on paintw or
ork/matt
k/matt /nish
/nishpaintw
paintw or
ork care
k care To
avo id damaging the paintwork and inter fering
with the driving assistance systems, please
obser vethefo llowing no tes: P
P
aint
aint
R Insect remains: soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: soak with water and rinse o.
aTer wards.
R Tree resin, oils, fuels and greases: remo veby
ru bbing gently with a clo thsoaked in petro-
leum ether or lighter 0uid.
R Coolant and brake 0uid: remo vewith a damp
clo thand clean water.
R Tar stains: use tarre mo ver.
R Wax: use silicone remo ver.
R Do not attach sti ckers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a quali/ed specialist workshop.
R Remo vedirt immediatel y,where possible.
Matt
Matt /nish
/nish
R Only use care products appr ovedfor
Mercedes-Benz.
R Do not attach stic kers, /lms or similar materi-
als. Only ha ve/lm attached tothe bumper at
a qu ali/ed specialist workshop. 340
340
Main
tenance and ca re

R
Do not polish theve hicle and light-alloy
wheels.
R Only use car washes that cor respond tothe
latest engineering standards.
R Do not use car wash prog rammes with a /nal
hot wax treatment.
R Do not use paint cleaners, bu1ng or polishing
products, gloss preser vers, e.g. wax.
In theev ent of paintwork damage:
R Always ha vepaintwork repairs car ried out at a
qu ali/ed specialist workshop.
R Make sure thera dar sensors function
(/ page 220). N
No
ot
tes on cleaning decor
es on cleaning decor ativ
ative f
e foils
oils Obser
vethe no tes on matt /nish care in thech ap-
te r "No tes on paintwork/matt /nish paintwork
care" (/ page 340). They also apply tomatt dec-
orative foils.
Obser vethe no tes on cleaning decorative foils to
av oid vehicle damage. Cleaning
Cleaning
R For cleaning, use plenty of water and a mild
cleaning agent without additives or abrasive
substances, e.g. a car shampoo appr ovedfor
Mercedes-Benz.
R Remo vedirt immediatel y,where possible,
whilst avoiding rubbing too hard. There is oth-
erwise a risk of damaging the decorative foil
ir re parabl y.
R Ifth ere is dirt on the /nish or if the decorative
fo il is dull: Use thePa int Cleaner recommen-
ded and appr ovedfo r Mercedes-Benz.
R Insect remains: Soak with insect remo ver and
ri nse o. the treated areas aTer wards.
R Bird droppings: Soak with water and rinse o.
aTer wards.
R Topreve ntwa ter stains, dry a foil-wrapped
ve hicle with a soT, absorbent clo thaTer every
car wash.
Av Av oiding damag
oiding damag e t
e to t
o t he decor
he decor ativ
ative f
e foil
oil
R The service life and colouring of decorative
fo ils are impaired by:
- Sunlight -
Tempe rature, e.g. hot air blo wer
- Weather conditions
- Stone chippings and dirt
- Chemical cleaning agents
- Oily products
R Do not use polish on matt decorative foil. Po l-
ishing will ha vethe e.ect of shining thefo il-
wrapped sur face.
R Do not treat matt or st ructured decorative
fo ils with wax.Pe rm anent stains may occur.
Scratches, cor rosive deposits, areas a.ected by
cor rosion and damage caused byincor rect care
cannot alw ays be comple tely re paired. In such
cases, visit a quali/ed specialist workshop.
Yo u can obtain more information on care and
cleaning products from the manufacturer.
In the case of foil-wrapped sur faces, optical di.er-
ences may occur between the sur faces that we re
not pro tected bya decorative foil aTer removing a
decorative foil. Maintenance and care
341
341