2021 LEXUS NX300h brake

711-4. Hybrid system
LEXUS NX300h Owners Manual_USA_M78578_en
1
For safety and security
vehicle with at least enough gasoline to
make the low fuel level warning light
( P.393) go off. If th ere is only a small
amount of fuel, the hybrid system may not
be able to start. (The standard amount of
fuel is about 2.7 gal. [10.1 L, 2.2 Imp.gal.],
when the vehicle is on a level surface. This
value may vary when the vehicle is on a
slope. Add extra fuel when the vehicle is
inclined.)
■Electromagnetic waves
●High voltage parts and cables on hybrid
vehicles incorporate electromagnetic
shielding, and ther efore emit approxi-
mately the same amount of electromag-
netic waves as conventional gasoline
powered vehicles or home electronic
appliances.
●Your vehicle may cause sound interfer-
ence in some third party-produced radio
parts.
■Hybrid battery (traction battery)
The hybrid battery (traction battery) has a
limited service life. The lifespan of the
hybrid battery (traction battery) can
change in accordance with driving style and
driving conditions.
WARNING
■High voltage precautions
This vehicle has high voltage DC and AC
systems as well as a 12-volt system. DC
and AC high voltage is very dangerous
and can cause severe burns and electric
shock that may result in death or serious
injury.
●Never touch, disassemble, remove or
replace the high voltage parts, cables
or their connectors.
●The hybrid system will become hot
after starting as the system uses high
voltage. Be careful of both the high
voltage and the high temperature, and
always obey the warning labels
attached to the vehicle.
●Never try to open the service plug
access hole located underneath the
rear seats. The service plug is used
only when the vehicle is serviced and is
subject to high voltage.
■Road accident cautions
Observe the following precautions to
reduce the risk of de ath or serious injury:
●Pull your vehicle off the road, shift the
shift lever to P, apply the parking brake,
and turn the hybrid system off.
●Do not touch the high voltage parts,
cables and connectors.
●If electric wires are exposed inside or
outside your vehicle, an electric shock
may occur. Never touch exposed elec-
tric wires.
●If a fluid leak occurs, do not touch the
fluid as it may be st rong alkaline elec-
trolyte from the hybrid battery (trac-
tion battery). If it comes into contact
with your skin or eyes, wash it off
immediately with a large amount of
water or, if possible, boric acid solu-
tion. Seek immediate medical atten-
tion.
●If a fire occurs in the hybrid vehicle,
leave the vehicle as soon as possible.
Never use a fire extinguisher that is not
meant for electric fires. Using even a
small amount of water may be danger-
ous.

802-1. Instrument cluster
LEXUS NX300h Owners Manual_USA_M78578_en
2-1.Instrument cluster
For the purpose of explanatio n, the following illustration displays all warning lights
and indicators illuminated.
The units used on the meter and some in dicators may differ depending on the tar-
get region.
Warning lights inform the driver of mal-
functions in any of the vehicle’s sys-
tems.
Warning lights and indicators
The warning lights and indicators inform th e driver of the status of the vehicle’s
various systems.
Instrument cluster
Warning lights
(U.S.A.)
Brake system warning light*1
(  P.388)
(Red)
(Canada)
Brake system warning light*1
(  P.388)
Charging system warning
light
*2 (  P.388)
Output control warning light*2
(  P.388, 399)
Low engine oil pressure warn-
ing light
*2 (  P.389)
High coolant temperature
warning light
*2 (  P.389)
(Yellow)
Brake system warning light*1
(  P.389)
(U.S.A.)
Malfunction indicator lamp*1
(  P.389)

812-1. Instrument cluster
LEXUS NX300h Owners Manual_USA_M78578_en
2
Vehicle status information and indicators
*1: These lights turn on when the power
switch is turned to ON mode to indi-
cate that a system check is being per-
formed. They will turn off after the
hybrid system is on, or after a few sec-
onds. There may be a malfunction in a
system if the lights do not turn on, or
turn off. Have the vehicle inspected by
your Lexus dealer.
*2: This light illuminates on the multi-infor-mation display.
*3: The light flashes to indicate a malfunc-tion.
*4: This light illuminates on the center panel.
(Canada)
Malfunction indicator lamp*1
(  P.389)
SRS warning light
*1 (  P.390)
(U.S.A.)
ABS warning light*1 ( P.390)
(Canada)
ABS warning light*1 ( P.390)
(Yellow)
Electric power steering sys-
tem warning light
*1 ( P.390)
(Red)
Electric power steering sys-
tem warning light
*1 ( P.390)
PCS warning light
*1 (  P.391)
(Orange)
LTA indicator*2 (if equipped)
(  P.391)
LDA indicator
*2 (if equipped)
(  P.391)
PKSB OFF indicator
*1, 3 (if
equipped) ( P.392)
Slip indicator light
*1 (  P.392)
Brake hold operated indica-
tor
*1, 3 (  P.392)
(U.S.A.)
Parking brake indicator*3
(  P.392)
(Canada)
Parking brake indicator*3
(  P.392)
Low fuel level warning light
(  P.393)
Driver’s and front passenger’s
seat belt reminder light
( P.393)
Rear passengers’ seat belt
reminder light
*4 (  P.393)
Master warning light
*1
(  P.394)
Tire pressure warning light
*1
(  P.394)
Brake Override Sys-
tem/Drive-Start Control warn-
ing light
*2 (  P.395)
WARNING
■If a safety system warning light does
not come on
Should a safety system light such as the
ABS and SRS airbag warning light not
come on when you start the hybrid sys-
tem, this could mean that these systems
are not available to help protect you in an
accident, which could result in death or
serious injury. Have the vehicle inspected
by your Lexus dealer immediately if this
occurs.

822-1. Instrument cluster
LEXUS NX300h Owners Manual_USA_M78578_en
The indicators inform the driver of the
operating state of the vehicle’s various
systems.
Indicators
Turn signal indicator (P.183)
(U.S.A.)
Headlight indicator ( P.190)
(Canada)
Tail light indicator ( P.190)
Headlight high beam indicator
(  P.192)
Automatic High Beam indica-
tor ( P.193)
Fog light indicator ( P.196)
“READY” indicator ( P.174)
EV indicator ( P.68)
EV drive mode indicator
*2
(  P.178)
“Eco” indicator
*2 (  P.270)
“Sport” indicator
*2 (if
equipped) ( P.270)
“Sport S” indicator
*2 (if
equipped) ( P.270)
“Sport S+” indicator
*2 (if
equipped) ( P.270)
“Custom” indicator
*2 (if
equipped) ( P.270)
Dynamic radar cruise control
indicator
*2 (  P.237)
Cruise control “SET” indica-
tor
*2 ( P.237)
Cruise control indicator
*2
(  P.237)
(White)
LTA indicator*2 (if equipped)
(  P.223)
LDA indicator
*2 (if equipped)
(  P.232)
(Green)
LTA indicator*2 (if equipped)
(  P.223)
LDA indicator
*2 (if equipped)
(  P.232)
(Orange)
LTA indicator*2, 3 (if equipped)
(  P.223)
LDA indicator
*2, 3 (if
equipped) ( P.232)
Intuitive parking assist indica-
tor (if equipped) ( P.248)
PKSB OFF indicator
*1, 4 (if
equipped) ( P.254)
Slip indicator light
*1, 3
(  P.273)
VSC off indicator
*1, 4
(  P.274)
PCS warning light
*1, 4
(  P.213)
(U.S.A.)
Parking brake indicator
( P.184)
(Canada)
Parking brake indicator
( P.184)
Brake hold standby indicator
*1
(  P.187)
Brake hold operated indica-
tor
*1 (  P.187)

872-1. Instrument cluster
LEXUS NX300h Owners Manual_USA_M78578_en
2
Vehicle status information and indicators
■Hybrid System Indicator
Power area
Shows that an Eco-friendly driving
range is being exceeded (during full
power driving etc.)
Eco area
Shows that the vehicle is being driven in
an Eco-friendly manner.
Hybrid Eco area
Shows that gasoline engine power is not
being used very often.
The gasoline engine will automatically
stop and restart under various condi-
tions.
Charge area
Shows that energy is being recovered
via the regenerative brake.
●Hybrid System Indicator is displayed
when the driving mode is in other than
the Sport mode.
●By keeping the indicator needle within
Eco area, more Eco-friendly driving can
be achieved.
●Charge area indicates regeneration* sta-
tus. Regenerated energy will be used to
charge the hybrid battery (traction bat-
tery).
*: When used in this manual, “regeneration”
refers to the conversion of energy cre-
ated by the movement of the vehicle into
electrical energy.
■Tachometer
Hybrid System Indicator switches to the
tachometer when drivin g mode is in Sport
mode. The settings of the tachometer dis-
play can be changed on the multi-informa-
tion display.
■Engine speed
On hybrid vehicles, engine speed is pre-
cisely controlled in order to help improve
fuel efficiency and reduce exhaust emis-
sions, etc.
There are times when the engine speed that
is displayed may differ even when vehicle
operation and driving conditions are the
same.
■Outside temperature display
●In the following situations, the correct
outside temperature may not be dis-
played, or the display may take longer
than normal to change.
• When stopped, or driving at low speeds
(less than 12 mph [20 km/h])
• When the outside temperature has changed suddenly (at the entrance/exit of
a garage, tunnel, etc.)
●When “--” or “E” is displayed, the system
may be malfunctioning.
Take your vehicle to your Lexus dealer.
■Pop-up display
In some situations, a pop-up display will be
temporarily displayed on the multi-informa-
tion display or the odometer/trip
meter/maintenance required information
screen.
The pop-up display function can be set
on/off. ( P.93)
■Liquid crystal display
Small spots or light sp ots may appear on the
display. This phenomenon is characteristic
of liquid crystal disp lays, and there is no
problem continuing to use the display.
■Customization
The meter display can be customized on
A
B
C
D

902-1. Instrument cluster
LEXUS NX300h Owners Manual_USA_M78578_en
will be shown.
Call sending/receiving and history
display
Linked with the hands-free system, sending
or receiving call is displayed. For details
regarding the hands-fr
ee system, refer to
the “NAVIGATION AND MULTIMEDIA
SYSTEM OWNER’S MANUAL”.
■Content displayed as drive infor-
mation
Select to display various drive data.
Items displayed can be switched by
pressing or of the meter con-
trol switches to select and pressing
or .
 Current fuel consumption
*1
Displays the current rate of fuel consump-
tion
Average fuel consumption (after
reset
*2/after start/after refuel)*1
Displays the average fuel consumption
since the function was reset, the hybrid sys-
tem was started, and the vehicle was refu-
eled, respectively
Use the displayed average fuel consump-
tion as a reference.
 Average vehicle speed (after
reset
*2/after start)*1
Displays the average vehicle speed since
the function was reset and the hybrid sys-
tem was started, respectively
Elapsed time (after reset*2/after
start)
*1
Displays the elapsed time since the func-
tion was reset and the hybrid system was
started, respectively
 Distance (driving range/after start)*1
Displays the estimated maximum distance
that can be driven with the quantity of fuel
remaining and the distan ce driven after the
hybrid system was started respectively.
• This distance is computed based on your average fuel consumption. As a result,
the actual distance that can be driven
may differ from that displayed.
• When only a small amount of fuel is added to the tank, the display may not be
updated.
When refueling, turn the power switch
off. If the vehicle is refueled without turn-
ing the power switch off, the display may
not be updated.
*1: Displayed when the it em is set in “Drive
Info 1”, “Drive Info 2” and “Drive Info 3”.
*2: The function can be reset by pressing
the of the meter control switches
for longer than 1 second when the item
to reset is displayed.
If there is more than one item that can
be reset, the item selection screen will
appear.
■Energy monitor
 P.99
■G monitor (if equipped)
Displays the acceleration forces of the
front, back, left and right of the vehicle.
Also displays the turning angle of the
steering wheel, brake oil pressure,
accelerator opening.
 The actual vehicle conditions may
differ from those on the display
Drive information
E

932-1. Instrument cluster
LEXUS NX300h Owners Manual_USA_M78578_en
2
Vehicle status information and indicators
which sounds when the parking support
alert is operated.
■ PKSB (Parking Support
Brake function) (if equipped)
(  P.253)
 PKSB on/off
Select to enable/dis able the parking sup-
port brake function (for static objects).
■ RSA (Road Sign Assist) (if
equipped) ( P.235)
Select to set up the following items.
 Road Sign Assist
Select to enable/disable road sign assist.
Over Speed
Select to set the over speed alert on/off.
Level of Over Speed
Select to set the over speed alert level.
Others
Select to set the other road sign assist.
■Clock
Select to switch between 12-hour dis-
play and 24-hour display.
■Vehicle Settings
 PBD (Power Back Door)
*1
(  P.114)
Select to set up the following items.
•System settings
Select to enable/dis able the power back
door system.
•Volume
Select to set the volume of the buzzer
which sounds when the power back door
system. • Kick Sensor
*2
Select to enable/dis
able the kick sensor.
*1: Vehicles with power back door
*2: Vehicles with Hand s Free Power Back
Door
 TPMS (Tire Pressure Warning Sys-
tem) ( P.359)
Select to initialize the tire pressure warning
system.
 Scheduled Maintenance ( P.339)
Select to initialize the scheduled mainte-
nance.
 Oil maintenance ( P.350)
Select to reset the engine oil maintenance
information (message indicating mainte-
nance is required and distance until the
next oil change) after engine oil mainte-
nance is performed.
■Meter settings
 Language
Select to change the language on the dis-
play.
 Units
Select to change the unit of measure for
fuel consumption.
 EV Indicator ( P.68)
Select to set the EV indicator on/off.
 Switch settings ( P.89)
Displays a procedure to register a desired
screen to
.
You can register 1 screen as a shortcut,
which can be displayed by pressing
.
 Drive information screen ( P.90)

952-1. Instrument cluster
LEXUS NX300h Owners Manual_USA_M78578_en
2
Vehicle status information and indicators
*:If equipped
Head-up display
Display brightness will change automati-
cally according to the brightness of the sur-
rounding area.
Display position adjustment switch
Display brightness adjustment
switch
Display brightness can be adjusted to the
desired level.
“HUD” button
“DISP” button 
Vehicle speed
 Hybrid System Indicator ( P.97)
 Tachometer
 Shift position and shift range
Displays the selected shift position or
selected shift range ( P.180)
 Audio display
Displays audio information for approxi-
mately 3 seconds when the audio system is
operated
Route guidance display (vehicles
with navigation system) ( P.98)
When approaching an intersection while
the navigation system is giving route guid-
ance, an arrow will automatically be dis-
played to indicate the direction of travel.
Lane departure warning display
(LTA [Lane Tracing Assist]) (if
equipped) ( P.218)
 Lane departure warning display
(LDA [Lane Departure Alert with
steering control]) (if equipped)
( P.227)
 Approach warning display
(Dynamic radar cruise control with
full speed range) ( P.243)
 Road signs (RSA [Road Sign
Assist]) (if equipped) ( P.235)
 Pre-collision warning message (Pre-
Collision System) ( P.211)
 Speed limit display (vehicles with
navigation system) ( P.98)
 Parking Support Brake function (for
static objects) (if equipped)
( P.253)
Head-up display*
The head-up display can be used to
project vehicle speed and other
information onto the windshield.
System components
A
B
C
D
E
Head-up display contents