2021 JEEP PATRIOT Owner handbook (in English)

Select Another Mobile Phone
This feature allows you to select and start using
another phone paired with the Uconnect Phone.
•Push the Phone
button to begin.
•After the “Ready” prompt and the following
beep, say “Setup Select Phone” and follow
the prompts.
•You can also push the Phone
button at
any time while the list is being played, and
then choose the phone that you wish to
select.
•The selected phone will be used for the next
phone call. If the selected phone is not
available, the Uconnect Phone will return to
using the highest priority phone present in or
near (approximately within 30 ft. [9 m]) the
vehicle.
Delete Uconnect Phone Paired Mobile
Phones
To delete mobile phones paired with the
Uconnect phone using Voice Commands:
1. Push the Phone
button to begin.2. After the “Ready” prompt and the following
beep, say “Setup Phone Pairing.”
3. At the next prompt, say “Delete” and follow
the prompts.
•You can also push the Phone
button at
any time while the list is being played, and
choose the phone you wish to delete.
Things You Should Know About
Your Uconnect Phone
Uconnect Phone Tutorial
To hear a brief tutorial of the system features,
push the Phone
button and say “Uconnect
Tutorial.”
Voice Training
For users experiencing difficulty with the system
recognizing their voice commands or numbers,
the Uconnect Phone Voice Training feature may
be used. To enter this training mode, follow one
of the two following procedures:
•From outside the Uconnect Phone mode
(e.g., from radio mode), push and hold the
Voice Command
button for five seconds
until the session begins, or,•Push the Voice Command
button and say
the “Voice Training,” “System Training,” or
“Start Voice Training” command.
You can either push the Uconnect Phone button
to restore the factory setting or repeat the words
and phrases when prompted by the Uconnect
Phone. For best results, the Voice Training
session should be completed when the vehicle
is parked with the engine running, all windows
closed, and the blower fan switched off.
This procedure may be repeated with a new
user. The system will adapt to the last trained
voice only.
Reset
To Reset all settings using Voice Command:
1. Push the Phone
button.
2. After the “Ready” prompt and the following
beep, say “Setup,” then “Reset.”
•This will delete all phone pairing, phone
book entries, and other settings in all lan-
guage modes. The System will prompt you
before resetting to factory settings.
77

Voice Command
•For best performance, adjust the rearview
mirror to provide at least ½ inch (1 cm) gap
between the overhead console (if equipped)
and the mirror.
•Always wait for the beep before speaking.
•Speak normally, without pausing, just as you
would speak to a person sitting a few feet/
meters away from you.
•Make sure that no one other than you is
speaking during a Voice Command period.
•Performance is maximized under:
•low-to-medium blower setting
•low-to-medium vehicle speed
•low road noise
•smooth road surface
•fully closed windows
•dry weather condition
•The system may not always work for some
accents.•When navigating through an automated sys-
tem such as voice mail, or when sending a
page, at the end of speaking the digit string,
make sure to say “Send.”
•Storing names in the phonebook when the
vehicle is not in motion is recommended.
•It is not recommended to store similar sound-
ing names in the Uconnect Phonebook.
•Phonebook (Downloaded and Uconnect
Phone Local) name recognition rate is opti-
mized when the entries are not similar.
•Numbers must be spoken in single digits.
“800” must be spoken “eight-zero-zero” not
“eight hundred.”
•You can say “O” (letter “O”) for “0” (zero).
•Even though international dialing for most
number combinations is supported, some
shortcut dialing number combinations may
not be supported.
•In a convertible vehicle, system performance
may be compromised with the convertible top
down.Far End Audio Performance
Audio quality is maximized under:
•Low-to-medium blower setting
•Low-to-medium vehicle speed
•Low road noise
•Smooth road surface
•Fully closed windows
•Dry weather conditions
•Operation from the driver’s seat
•Performance, such as audio clarity, echo,
and loudness to a large degree rely on the
phone and network, and not the Uconnect
Phone
•Echo at the phone far end can sometimes be
reduced by lowering the in-vehicle audio
volume
Recent Calls
If your phone supports “Automatic Phonebook
Download,” Uconnect Phone can list your Out-
going, Incoming and Missed Calls.
78

Voice Text Reply
Uconnect Phone can read or send new mes-
sages on your phone.
Read Messages:
If you receive a new text message while your
phone is connected to Uconnect Phone, an
announcement will be made to notify you that
you have a new text message. If you wish to
hear the new message:
1. Push the Phone
button.
2. After the “Ready” prompt and the following
beep, say “SMS Read” or “Read Messages.”
3. Uconnect Phone will play the new text mes-
sage for you.
After reading a message, you can “Reply” or
“Forward” the message using Uconnect Phone.
Send Messages:
You can send messages using Uconnect
Phone. To send a new message:
1. Push the Phone
button.2. After the “Ready” prompt and the following
beep, say “SMS Send” or “Send Message.”
3. You can either say the message you wish to
send or say “List Messages.” There are 20
preset messages.
To send a message, push the Voice Command
button while the system is listing the mes-
sage and say “Send.” Uconnect Phone will
prompt you to say the name or number of the
person you wish to send the message to.
List of Preset Messages:
1. Yes.
2. No.
3. Where are you?
4. I need more direction.
5. L O L.
6. Why?
7. I love you.
8. Call me.9. Call me later.
10. Thanks.
11. See you in 15 minutes.
12. Iamonmyway.
13. I’ll be late.
14. Are you there yet?
15. Where are we meeting?
16. Can this wait?
17. Bye for now.
18. When can we meet?
19. Send number to call.
20. Start without me.
79

Turn Voice Text Reply Incoming Announce-
ment ON/OFF
Turning the Voice Text Reply Incoming An-
nouncement OFF will stop the system from
announcing the new incoming messages.
To turn Voice Text Reply incoming announce-
ment on or off using Voice Command:
1. Push the Phone
button.2. After the “Ready” prompt and the following
beep, say “Setup Incoming Message An-
nouncement,” you will then be given a
choice to change it.
Bluetooth Communication Link
Mobile phones have been found to lose connec-
tion to the Uconnect Phone. When this hap-
pens, the connection can generally be reestab-lished by switching the phone off/on. Your
mobile phone is recommended to remain in
Bluetooth ON mode.
Power-Up
After switching the ignition key from OFF to
either the ON or ACC position, or after a lan-
guage change, you must wait at least 15 sec-
onds prior to using the system.
80

81

82

83

Voice Commands
Primary Alternate (s)
zero
one
two
three
four
five
six
seven
eight
nine
asterisk (*) star
plus (+)
hash (#)
all all of them
Breakdown service
callPrimary Alternate (s)
cancel
confirmation
promptsconfirmation
continue
delete
dial
download
Dutch Nederlands
edit
emergency
English
delete all erase all
Espanol
Francais
German Deutsch
help
homePrimary Alternate (s)
Italian Italiano
language
list names
list phones
main menu return to main menu
mobile
mute
mute off
new entry
no
other
pair a phone
phone pairing pairing
phonebook phone book
previous
redial
select phone select
84