9-18Maintenance and schedules
110,000 Miles/132 Months/
176,000 Km
Standard maintenance:.Inspect brake lines and cables.Inspect brake pads and rotors.Inspect drive belts (1).Inspect propeller shaft (AWD models).Inspect drive shaft boots (AWD models).Inspect stop lamp switch and brake pedal
position switch (2)
.Inspect transfer fluid.Inspect differential gear oil.Replace engine oil and filter (3).Perform tire rotation (4)
Severe maintenance:
.Inspect brake pads and rotors.Inspect exhaust system.Inspect steering gear and linkage.Inspect axle and suspension parts.Inspect propeller shaft (AWD models).Inspect drive shaft boots (AWD models).Replace brake fluid
(1) Replace the drive belts if found damaged.
(2) Inspect the clearance between the brake pedal
and the switches.
(3) If the oil replacement indicator is displayed,
change the engine oil and filter as soon as
possible. After replacing the engine oil, reset the
display.
(4) If your vehicle is equipped with different sized
tires in the front and rear, tires cannot be rotated.
115,000 Miles/138 Months/
184,000 Km
Standard maintenance:.Perform tire rotation (1)
Severe maintenance:
.Inspect brake pads and rotors.Inspect exhaust system.Inspect steering gear and linkage.Inspect axle and suspension parts.Inspect propeller shaft (AWD models).Inspect drive shaft boots (AWD models)
(1) If your vehicle is equipped with different sized
tires in the front and rear, tires cannot be rotated.
120,000 Miles/144 Months/
192,000 Km
Standard maintenance:.Inspect brake lines and cables.Inspect brake pads and rotors.Inspect drive belts (1).Inspect EVAP vapor lines and fuel lines.Inspect exhaust system.Inspect propeller shaft (AWD models).Inspect drive shaft boots (AWD models).Inspect steering gear and linkage.Inspect axle and suspension parts.Inspect stop lamp switch and brake pedal
position switch (2)
.Inspect transfer fluid.Inspect differential gear oil.Replace air cleaner filter (3).Replace brake fluid.Replace engine oil and filter (4).Replace In-cabin microfilter.Replace Intelligent Key battery.Perform tire rotation (5)
wwwapps.tc.gc.ca/Saf-Sec-Sur/7/
PCDB-BDPP/fc-cp.aspx?lang=fra
(French speakers).
Additional information concerning
motor vehicle safety may be obtained
from Transport Canada’s Road
Safety Information Centre at 1-
800-333-0371 or online at www.tc.
gc.ca/ roadsafety (English speakers)
or www.tc.gc.ca/securiteroutiere
(French speakers).
To notify INFINITI of any safety
concerns please contact our Consu-
mer Information Centre toll free at 1-
800- 361-4792.
WARNING
A vehicle equipped with Intelligent All-
Wheel Drive (AWD) should never be
tested using a two wheel dynamometer
(such as the dynamometers used by
some states for emissions testing), or
similar equipment. Make sure you inform
test facility personnel that your vehicle
is equipped with AWD before it is placed
on a dynamometer. Using the wrong test
equipment may result in transmission
damage or unexpected vehicle move-
ment which could result in serious vehicle
damage or personal injury.
Due to legal requirements in some states/
areas, your vehicle may be required to be in
what is called the “ready condition” for an
Inspection/Maintenance (I/M) test of the
emission control system.
The vehicle is set to the “ready condition”
when it is driven through certain driving
patterns. Usually, the “ready condition” can
be obtained by ordinary usage of the vehicle.
If a powertrain system component is re-
paired or the battery is disconnected, the
vehicle may be reset to a “not ready condi-
tion”. Before taking the I/M test, check the
vehicle’s inspection/maintenance test readi- ness condition. Place the ignition switch in
the ON position without starting the engine.
If the Malfunction Indicator Light (MIL)
comes on steady for 20 seconds and then
blinks for 10 seconds, the I/M test condition
is “not ready”. If the MIL does not blink after
20 seconds, the I/M test condition is
“ready”.
It is recommended you visit an INFINITI
retailer to set the “ready condition” or to
prepare the vehicle for testing.
Technical and consumer information10-23
READINESS FOR INSPECTION/
MAINTENANCE (I/M) TEST (US only)
