2021 AUDI Q2 turn signal

Navigation
- The route calculated by the navigation sys­
tem is a recommendation of how best to
reach a destination. Pay attention to traffic

lights,
no stopping signs, lane change re­
strictions, one-way streets, etc.
© CAUTION
-Should the navigation directions contradict
the current traffic regulations, you must al­
ways follow the traffic regulations.
- The volume should only be set at a level
which enables you to hear distant police and
emergency vehicles clearly - failure to do so
could result in an accident.
© Note
- Snow or other obstructions on the GPS aer­
ial or interference caused by trees or large
buildings could affect the reception of the
satellite signals and make positioning
diffi­

cult. GPS reception and vehicle positioning
can also be adversely affected by deactiva­
tion or a malfunction of several satellites.
- Road names can change; therefore the
names stored on the MMI may be different
from the actual names in exceptional cases.
Entering a destination
Searching for navigation destinations
Applies to: vehicles with navigation system
With the search function, you can use the MMI
touch
pad*
or the speller for letters/numbers to
enter navigation destination information in any
order (e.g. Forest Road 20 London).
You
can
search for special destinations, contacts, recent
destinations or favourites in the same way to
help you navigate to the desired address.
Press the |NAV/MAP| button repeatedly untiL the
Enter destination menu is displayed
opage
207,
Fig. 172.
• Push the rotary pushbutton upwards. The entry
field will be displayed
@ ^>page
207, Fig. 172.
- Enter one or more search terms in the entry

field.

- If appropriate, confirm an autocomplete
sug­

gestion*
or a suggested word*. Refer to

^page
159, Speller for letters/numbers.
- Turn the rotary pushbutton clockwise to switch
to the results list.
- Select a destination from the results list and
confirm it.
- Select and confirm Start route guidance.
The route will be displayed as an overview on the

map.
Route guidance is already active.
Narrowing the search area
All countries are preselected for the search func­
tion at the factory.
-In the input menu
(T)<=>page207,
Fig. 172, se­
lect the right controL button > Country selec­

tion.

- Select the country flvj) which you would Like to
search in. This will limit the number of results
and speed up the search. The entry selected in
the country selection menu will be stored.
© Note
- The terms suggested by the MMI depend on
the destinations to which you have recently

driven.

- Up to 50 entries are stored in the list of des­
tinations to which you have recently driven.
- For more information on the search func­

tion,
please refer to
^>page
160.
Loading last destination
Applies to: vehicles with navigation system

The
destinations you have most recently driven
to are stored automatically and can be loaded
directly as new destinations.
Important: You must have set
a
destination in
the past.

•
Press the |NAV/MAP| button repeatedly until
the Enter destination menu is displayed

opage
207, Fig. 172.
The destinations to which you have recently driv­
en are listed directly in the Enter destination
menu under your home address and marked with
the
symbol®^
page
207, Fig. 172. •
208

System settings

System settings
Setting the time and
date

The
time can be set manually or via
GPS*

• Select:
|MENU|
button > Settings
>
left control
button > MMI settings > Date & time.

•
Or: Select:
|MENU|
button > Car
>
left control
button
>
Vehicle settings > Date & time.
Set automatically
The time and date are automatically updated
when this function is switched on
0.

Time
Important: The Set automatically function must
be deactivated.
Press the rotary pushbutton. You can adjust the
time manually by turning and pressing the rotary
pushbutton.
Date
Important: The Set automatically function must
be deactivated.
Press the rotary pushbutton. You can adjust the
date manually by turning and pressing the rotary
pushbutton.
Time zone
When selecting the correct time zone, a list of
corresponding countries is displayed as an exam­

ple.

Automatic time zone*
When this function is activated
(vf,
the time is au­
tomatically adjusted to the relevant time zone.
Automatic summer time*
When this function is activated
0,
the time is au­
tomatically adjusted from normal time to sum­
mer time.
Time format
When this option is set to 24h, for example
13:00 will be displayed as the time. When
it
is
set to AM/PM, for example 1:00 PM will be dis­

played.

Date format
When this option is set to DD.MM.YYYY, for ex­
ample
31.08.2017
will be displayed as the date.
When
it
is set to MM/DD/YYYY, for example

08/31/2017
will be displayed. When
it
is set to
YYYY-MM-DD, for example
2017-08-31
will be

displayed.

MMI settings

•
Select:
|MENU|
button > Settings > left control
button > MMI settings.
Language
You can change the language of the display along
with the language of the navigation cues* and
the speech dialogue system*.
The number of languages available depends on
the market.
Measurement units
The following measurement units are available:
- Speed (km/h or
mph)

- Distance (km or miles)
- Temperature (°C or °F)
- Consumption
(ltr/100
km,
mpg
(US),
mpg
(UK)
or
km/ltr)

- Capacity (litres, gallons)
Reminder signal
Applies to: vehicles with Audi phone box
Important: Your mobile phone must be Qi com­

patible1^,
or
it
must be connected to the Audi
music interface
(l) ^page
177, Fig. 161 using a
USB adapter cable.
You can use the reminder signal to keep yourself
informed of the charging status of the mobile
•

CO

<
O
rN
iv
rN
t-H
o < 00

1}
The Qi standard enables you to charge your mobile phone
wirelessly.
255

System settings
phone in the Audi phone box*. The following set­
tings are available:
- off: Switches the reminder signal off.
-
sound:
A sound is played as the reminder
sig­

nal.

- spoken: The reminder signal is spoken by the

system.

Reminder signal volume: You can adjust the
vol­

ume of the reminder signal by turning the rotary
pushbutton.
Switch off pop-up: This function is switched off
at the factory. When this function is switched on

fcTf,
the messages about the charging status of
the mobile phone in the Audi phone box* on the
infotainment display will not appear. The re­
minder not to forget the mobile phone when
leaving the vehicle will also be switched off.
Usage tips
Your MMI dispLays usage tips when this function
is switched on
5f.
They will appear less often as
time goes by.
Speech dialogue system
Applies to: vehicles with speech dialogue system
The following functions are available depending
on the equipment installed in your vehicLe:
Command display: The MMI displays possible
voice commands in the corresponding menu
when this function is switched on
Sf.

Short dialogue: When this function is switched
on
(vj,
the spoken cues are shortened.
Command during speech dialogue*: This option
is activated when the vehicle leaves the factory.
When this option is activated
(vf,
you can say a
new command while the system is giving a spo­
ken cue, rather than waiting for the beep. When
this option is deactivated
O,
wait until you hear
the beep to say
a
command.
Volume: You can adjust the volume of the spoken
cues by turning the rotary pushbutton.
Individual speech training (only possibLe when
the vehicle is stationary): You can use the individ­
ual speech training to adapt the speech dialogue
system to your voice or pronunciation so that the
speech dialogue system can then better recog­
nise what you are saying. The individual speech
training prompts you to repeat 20 spoken phra­
ses that consist of certain commands and blocks
of digits. If
you
would like to delete the stored
speech training setup, you can use the function
Reset individual speech training.
Display brightness
Display brightness: You can adjust the bright­
ness of the infotainment display by turning the
rotary pushbutton.
Factory settings
You can reset the following functions to the fac­
tory settings:
- Sound settings
- Radio
- Media settings
-Jukebox*
- Directory
-Telephone
- Bluetooth and Wi-Fi*
- Navigation settings*
- Navigation and online memory*
- Speech dialogue system*
- Message settings*
- Apps*
-Usage tips
-Audi connect*
- Audi smartphone interface*
You can select the desired options individually or
mark Select all entries. SeLect and confirm Re­
store factory settings.
Please note that not only settings will be de

Leted
when you do this; saved data may also
be erased
256

Safe driving
Safe driving
General notes
Safety is the first priority
The safety features in your vehicle are harmon­
ised to provide you and your passengers with the
best possible protection in accident situations.
However, they can only be effective if you and
your passengers sit in the correct position and
adjust and use the safety equipment properly.
For these reasons, this chapter explains why
these safety features are so important, how they
can protect you, what you need to remember
when using them, and
how
you and your passen­
gers can gain the most benefit from them. There
are also a number of important safety warnings
which you and your passengers should always ob­
serve in order to minimise the risk of injury.
WARNING
- The information in this chapter is important
for the driver of the vehicle and all passen­

gers.
The other chapters in this manual

(and,
where applicable, in the other litera­
ture supplied with the vehicle) contain fur­
ther important notes which you should read
and observe for your own safety and that of
your passengers.
- Ensure that the complete vehicle wallet is
always in the vehicle. This is especially im­
portant when you lend or sell the vehicle to
others.

CO

<
O
rN
iv
rN
i—i
o < 00
Before every trip
The driver is responsible for the safety of the
passengers and the safe operation of the vehicle
at all times.

For
your own safety and the safety of your pas­
sengers, always note the following points before
every trip:

•
Make sure that all lights and turn signals are
working properly.

•
Check the tyre pressures.

•
Make sure that all windows are clean and give
good visibility to the outside.

•
Secure all luggage and other items carefully

•=>
page 272.
• Make sure that no objects can interfere with
the pedals.

•
Adjust the front seat, head restraint and mir­
rors correctly.
• Applies to: adjustable head restraints: Make
sure that the front passenger's head restraint is
adjusted to the correct position.
• Applies to: adjustable head restraints: Make
sure that the head restraints for the rear pas­
sengers are in the fully raised position.

•
Make sure that children are protected with suit­
able safety seats and properly worn seat belts

•=>
page 267.

•
Sit in the correct position in your seat. Make
sure
that
your passengers are sitting in the cor­
rect positions
^>page
58.

•
Fasten your seat belt correctly. Make sure that
your passengers do the same
^page
275.
What factors can impair your safety?
Safety on the road is directly related to
how
you
drive, and can also be affected by the passengers
in the vehicle.
• The driver is responsible for the safety of the
vehicle and all its occupants. If your ability to
drive is impaired in any way, you endanger
yourself and other road users
,=>^.
Therefore:
• Do not let yourself be distracted by passengers
or by using a mobile phone, etc.

•
Never drive when your driving ability is im­
paired (by medication, alcohol, drugs, etc.).
• Obey all traffic regulations and speed limits
and always maintain a safe distance to the
vehi­

cle in front.

•
Always adjust your speed to suit the
road,
traf­
fic and weather conditions.

•
Take frequent breaks on long trips. Do not drive
for more than two hours without a stop.

•
If possible, avoid driving when you are tired or

stressed.
•
263

Mobility

CO

rN
IV
rN
•-i

00
Additional notes on towing by breakdown
truck
If one of the axles has to be raised in order to
tow the vehicLe, please refer to the following ta­
ble to determine the appropriate axle
for
your
gearbox/drive combination:
Manual
gearbox
Automatic
gearbox
Front-wheel
drive
Front or rear
axle
Front axle
Four-wheel
drive
Front or rear
axle
Front axle
Applies to vehicles with four-wheel drive: If the
vehicle is to be towed with one of the axles

raised,
the ignition must be switched off; other­
wise the drive train can be damaged.
Notes on tow-starting
Applies to vehicles with automatic gearbox: For
technical reasons, your vehicle must not be tow-

started.

Applies to vehicles with manual gearbox: As a
general rule, tow-starting is not recommended.
If the engine will not start, it is best to try start­
ing it using the battery of another vehicle

*>page
326 before attempting to tow start. If
this is not possible, you can try to push-start or
tow-start the vehicle
*page
330, Tow-starting.
A WARNING
There is a high risk of accidents when towing/
tow-starting, as the towed vehicle can easily
be driven into the towing vehicle.

UTION

- If it is not possible to tow the vehicle as de­
scribed above (e.g. due to a gearbox failure
or if the vehicle has to be towed further
than 50 km), it must be transported on a
special car transporter or trailer.
- Towing a vehicle with the wrong axle raised
can cause serious damage to the gearbox.
- Applies to vehicles with automatic gearbox:
It is not possible to move the selector lever
out of position
P
if the electrical power sup­
ply fails. Before the vehicle can be recov­
ered/manoeuvred you must manually re­
lease the selector lever; left-hand drive
vehicles
*page
93, right-hand drive
vehicles
*page
94.
- Please observe the relevant regulations
when towing or tow-starting.
Towing away
Please observe the important safety warnings on

*
page 328.
Preparations
• Attach the tow-rope or the tow-bar only to the
towing anchorages provided
for
this purpose

opage
330,
*page
331.
• Please ensure that the tow-rope is not twisted
as it could otherwise unscrew the towline an­
chorage while the vehicle is being towed.
• The hazard warning lights of both vehicles
must normally be switched on
*page
52. How­
ever, observe any regulations to the contrary.
Towing vehicle (front)
• Ensure that the tow-rope is taut before you
drive off.
• Manual gearbox: Engage the clutch very gently
when starting to move and accelerate with par­
ticular care.
• Automatic gearbox: Accelerate slowly and
grad­

ually.
• Avoid unnecessary braking and manoeuvres.
Vehicle being towed (rear)
• Ensure that the ignition is switched on, the
steering wheel is not locked, and
that
you can
operate the turn signals, horn or windscreen
wipers if necessary
<=>/t\-

• The brake servo only works when the engine is

running.
The power steering only works when
329

Mobility
the ignition is on and the vehicle is moving1'.
Otherwise you will need to press the brake
ped­

al significantly harder and apply more force to
move the steering wheel.
• Please ensure that the steering wheel is un­
locked and that it moves freely.
• Release the parking brake
*page
82.
• Applies to vehicles with manual gearbox: Put
the gear lever in neutral.
• Applies to vehicles with automatic gearbox:
Move the selector lever to position N.
• Ensure that the tow-rope remains taut at all
times when towing.
© CAUTION
A WARNING
If the vehicle has no electrical power, do NOT
use a tow-bar or tow-rope to tow the vehicle
© Note
You can use the turn signals to indicate a
change of direction (or lane) even when the
hazard warning lights are on. The hazard
warning lights will be interrupted temporari-

Ly.

Tow-starting
Please observe the important safety warnings on

*page
328.
Important: Your vehicle must be fitted with a
manual gearbox. If your vehicle has a petrol en­

gine,
it must not be towed further than 50 me­
tres
*(J).

• Attach the tow-rope or the tow-bar only to the
towing anchorages provided
for
this purpose

*page
330,
*
page 331.
• Engage second or third gear before moving off.
• Press the clutch and hold the pedal down.
• Switch on the ignition.
• Once both vehicles are moving, release the

clutch.

• As soon as the engine starts, press the clutch
pedal and put the gear lever in neutral.
When tow-starting the vehicle, do not tow it
further than 50 metres; otherwise the cata­
lytic converter could be damaged.
Front towline anchorage

»

Fig.
271 Front bumper (right side): Removing cover cap

Fig.
272 Front bumper (right side): Towline anchorage
screwed in
The screw connection for the towline anchorage
is located behind a cover cap on the right side of
the front bumper.
• Take the towline anchorage out of the vehicle's
tool kit
*
page 319.
• Press the cover cap briefly but firmly inwards
-arrow-, detach it from the bumper and take it

out*Fig.
271.
• Screw the towline anchorage into the screw
connection as far as
it
will go
*Fig.
272 and
tighten it with the box spanner.
• Put the towline anchorage back in the tool kit
after use.

11
Important: The vehicle battery must be adequately charg­

ed.

330

Fuses and bulbs

CO

rN
IV
rN
•-i

00
- Make sure that the covers are correctly seat­
ed on the headlights and the rear lights.
This will ensure that water cannot enter the
housings and cause the lights to malfunc­

tion.

- Do not touch the glass part of the bulb with
your bare hands; use a cloth or paper towel

instead.
Otherwise, the fingerprints left on
the glass will vaporise as a result of the heat
generated by the bulb, be deposited on the
reflector and impair its surface.
© CAUTION
When removing or installing the rear light,
take care not to cause any damage.
- Removing the rear light in particular can
lead to the paintwork or rear light becoming

damaged.
This is another reason why we
recommend having the bulbs changed by a
qualified workshop.
- Never use metal tools (e.g. a screwdriver) or
sharp or pointed plastic tools to lever out
the rear light - risk of damaging the paint.
- Make sure you have a soft cloth ready to
place under the glass on the rear light, to
avoid any scratches.
® For the sake of the environment
A qualified workshop can advise you how to
dispose of used bulbs in the proper manner.
© Note
- Please check at regular intervals that
alL

lighting (especially the exterior Lighting) on
your vehicle is functioning properly. This is
not only in the interest of your own safety,
but also in that of all other road users.
- Before changing a bulb, make sure you have
the correct new bulb.
Bulbs at front of vehicle
Applies to: vehicles with halogen headlights

Fig.
279 Halogen headlights: Overview of left side of
vehi­

cle
You must only replace a bulb with a bulb of the
same type. Information regarding e.g. the wat­
tage can be found on the base of the bulb.
The description for changing the bulb refers to
the left headlight; the procedure for the right
headlight is similar.
Halogen headlights
The following bulbs can be changed:
Bulb (12 V)

(T)Main
beam headlight
© Dipped headlight
© Daytime running light
© Turn signal
Version

H7LL(55
W)

H7LL(55W)

PW24W
PWY24W
Bulbs at rear of vehicle
Applies to: vehicles with bulbs

Fig.
280
Rear
of
vehicle:
Bulbs on
leftside
of vehicle
335

Fuses and bulbs
You must only replace a bulb with a bulb of the
same type. Information regarding e.g. the wat­
tage can be found on the glass or base of the

bulb.

The description for changing the bulb refers to
the Left rear light unit; the procedure for the
right rear Light unit is similar.
You can change the
foLLowing
bulbs yourself:
Changing bulb for turn signals
Applies to: vehicles with halogen headlights
Bulb (12 V)

©Tail
light
© Brake light
© Reversing Light

(4)
Turn signal

©Rearfog
light3'

Version
W16W
P21W
W16W
PY21W
W16W

a'
The bulb for the rear fog light is fitted on one side only. It
is located on the left side on LHD vehicles and on the right
side on RHD vehicles.
Changing headlight
bulbs
Removing cover (engine compartment)
Applies to: vehicles with halogen headlights

^

Fig.
281 Headlight: Cover for turn signal and main beam
headlight
• Switch off the ignition and the lights.
• Open the bonnet.
• Turn the headlight cover anti-clockwise

*Fig.
281 and remove it
*/^
in General notes
on page 334.
• Change the bulb for the turn signal

*page
336 or the main beam headlight

*page
337.

Fig.
282 Headlight: Plastic connector for turn signal

Fig.
283 Headlight: Fitting plastic connector for turn
sig­

nal
Removing
• Pull the plastic connector together with the
buLb out of the headlight housing
*Fig.
282.
• Disconnect the plastic connector from the base
of the bulb
*^
in General notes on page 334.
Installing
• Push the new bulb into the plastic connector so
that it is securely seated
*^
in General notes
on page 334.
• Insert the bulb into the headlight housing.
•
Fit
the plastic connector
*Fig.
283 into the
housing and press it in until the side catches
engage.
• Put the cover back on.
• Check whether the new bulb is working.
336