2020 TOYOTA CAMRY display
[x] Cancel search: displayPage 36 of 52
34
TOYOTA SAFETY SENSE™
TURNING THE LDA SYSTEM ON/OFF
Press the LDA switch to turn the LDA system on. Depress again to turn it off.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
Refer to the Toyota Owner’s Manual for additional information on LDA operation,
settings adjustments, limitations, and precautions before attempting to use it.
LANE DEPARTURE ALERT
LDA function display
Steering assist indicator
LDA indicatorLane markers
(2) (1) - B O F % F Q B S U V S F " M F S U - % "
J O E J D B U P S T J M M V N J O B U J P O T I P X T U I F T Z T U F N P Q F S B U J P O
status.
Page 37 of 52
35 The LDA function
E J T Q M B Z T X I F O U I F . V M U J * O G P S N B U J P O % J T Q M B Z . * %
J T T X J U D I F E
to the driving assist system information screen.
5 I F T Z T U F N E J T Q M B Z T X I J U F T P M J E M J O F T B O E B X I J U F - % " J O E J D B U P S X I F O W J T J C M F M B O F
markers on the road are detected and system is operating. Both the LDA indicator
and a side line flashes yellow to alert the driver when the vehicle deviates from its
lane.
5 I F - % " J O E J D B U P S J T H S F F O X I F O T U F F S J O H B T T J T U G V O D U J P O J T P Q F S B U J O H
5 I F T Z T U F N E J T Q M B Z T P V U M J O F T P O U I F - % " J O E J D B U P S X I F O M B O F N B S L F S T P O U I F S P B E
are not detected or the function is temporarily cancelled.
Note: When operation conditions are no longer met, a function may be
temporarily canceled. However, when the operation conditions are met again,
operation of the function is automatically restored. For example, LDA may not
function on the side(s) where white/yellow lines are not detectable.
Refer to the Toyota Owner’s Manual for additional information on LDA operation,
settings adjustments, limitations, and precautions before attempting to use it.
ADJUSTING LDA ALERT SENSITIVITY
DISABLING STEERING ASSIST
5 I F E S J W F S D B O B E K V T U U I F T F O T J U J W J U Z P G U I F - % " X B S O J O H
G V O D U J P O G S P N U I F
. V M U J * O G P S N B U J P O % J T Q M B Z . * %
D V T U P N J [ B U J P O T D S F F O
High - Is designed to warn approximately before the front
tire crosses the lane marker.
Normal - Is designed to warn approximately when the front
tire crosses the lane marker.
1 S F T T i
” switches and select or from the Multi-Information Display
. * %
1 S F T T i
” switches and select the “Alert sensitivity” setting function and then
press “
.”
1 S F T T i
” each time to change the setting.
1 S F T T i
” to go back to the menu.
1 S F T T i
” switches and select or from the Multi-Information Display
. * %
1 S F T T i
” switches and select the “Steering Assist” setting function and then
press “
.”
1 S F T T i
” each time to change the setting.
1 S F T T i
” to go back to the menu.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
- " / & % & 1 " 3 5 6 3 & " - & 3 5 $ 0 / 5 * / 6 & %
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Page 38 of 52
36
TOYOTA SAFETY SENSE™
SWAY WARNING SYSTEM
SWS is a function of LDA and is designed to detect swaying based on the vehicle
location in the lane and the driver’s steering wheel operation. To help prevent
swaying, the system alerts the driver using a buzzer sound and a warning displays
in the MID.
Continuous lane deviations from
swaying.
Gentle swaying from driver’s
inattentiveness.
Acute steering wheel operation after the
number of operations decrease due to driver’s
inattentiveness.
1 S F T T i” switches and select or from the Multi-Information Display
. * %
1 S F T T i
” switches and select the “Sway sensitivity” setting function and then
press “
.”
1 S F T T i
” each time to change the setting.
1 S F T T i
” to go back to the menu.
1 S F T T i
” switches and select or from the Multi-Information Display
. * %
1 S F T T i
” switches and select the “Sway warning” setting function and then
press “
.”
1 S F T T i
” each time to change the setting.
1 S F T T i
” to go back to the menu.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
ADJUSTING SWAY ALERT SENSITIVITY
DISABLING LDA SWAY WARNING SYSTEM
Page 39 of 52
37
Dynamic Radar Cruise Control (DRCC) or
Full-Speed Range* DRCC
TURNING SYSTEM ON/OFF
ADJUSTING SET SPEED
Vehicle will cruise at a set speed, decelerate to maintain selected distance from a
slower vehicle traveling in front and accelerate back up to the selected speed if the
vehicle in front changes lanes or speeds up.
(1) Push “
” to turn DRCC system ON.
(2) Use the steering wheel controls to increase speed by pushing “+RES” or
decrease the speed by pushing “-SET”. Push and hold to make a large
B E K V T U N F O U P S Q V T I F B D I U J N F U P N B L F G J O F B E K V T U N F O U T N Q I < L N I > P S
L N I < N Q I > J O D S F N F O U T
(3) Push “Cancel” to cancel the adjusting speed operation.(1)
(2) (3)
DRCC helps maintain a pre-set distance to a preceding vehicle when the preceding
vehicle is traveling at a lower speed. This mode is always selected first when the cruise
control button is depressed. Constant speed cruise control mode is also available.
DRCC is designed to function at speeds between approximately 30 to 110 MPH and is
intended for highway use. Full-Speed Range* DRCC is designed to function at speeds
between 0 to approximately 110 MPH and is intended for highway use.
Resume/
Set speed
Cruise control
Set speed*If equipped.
Cancel
Cruise control
switches
1 V T I P O D F 0 O
1 V T I U X J D F 0 G G
Refer to page 39 for switching to Constant Speed (Cruise) Control Mode.
1 5 I F T F U T Q F F E N B Z C F S F T V N F E P O D F W F I J D M F T Q F F E F Y D F F E T N Q I L N I
2 The set speed may also be cancelled by depressing the brake pedal.
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Display
Set speedDynamic Radar Cruise Control
vehicle-to-vehicle distance button
Indicators
Increase speed/Resume1
Cancel2
Decrease speed
Page 41 of 52
39
4 8 * 5 $ ) * / ( 5 0 $ 0 / 4 5 " / 5 4 1 & & % $ 3 6 * 4 &
$ 0 / 5 3 0 - . 0 % &
4 & 5 5 * / ( $ 0 / 4 5 " / 5 4 1 & & % $ 3 6 * 4 &
$ 0 / 5 3 0 -
Note: When your vehicle is too close to a vehicle ahead, and sufficient automatic
deceleration via the cruise control is not possible, the display will flash and the
buzzer will sound to alert the driver. An example of this would be if another driver
cuts in front of you while you are following a vehicle. Depress the brake pedal to
ensure an appropriate vehicle-to-vehicle distance.
If you are already using DRCC “”, push button again to turn the system off
first, then push and hold button for at least 1.5 seconds to switch.
Note: When the engine is turned off, it will automatically default to DRCC.
Acceleration when there are no longer any preceding vehicles driving
slower than the set speed
The system accelerates until the set speed is reached. The system then
returns to constant speed cruising.
1.5 seconds
" % + 6 4 5 * / ( % * 4 5 " / $ & $ 0 / 5 * / 6 & %
Refer to the Toyota Owner’s Manual for additional information on DRCC operation,
settings adjustments, limitations, and precautions before attempting to use it.To adjust speed or cancel, see steps (2) and (3) of ADJUSTING SET SPEED on
page 37.
Increase speed
Decrease speed
OVERVIEW FEATURES & OPERATIONS TOYOTA SAFETY SENSE SAFETY & EMERGENCY FEATURES
Page 44 of 52
42
SAFETY & EMERGENCY FEATURES
Safety Connect® (if equipped)
Tire Pressure Monitoring (warning) System (TPMS)
The tire pressure detected by the tire pressure warning system can
C F E J T Q M B Z F E P O U I F N V M U J J O G P S N B U J P O E J T Q M B Z . * %
Refer to the load label on the door jamb or the Owner’s Manual for tire inflation
specifications.
If the tire pressure indicator flashes for more than 60 seconds and then remains on,
take the vehicle to your local Toyota dealer.
NOTE: The warning light may come on due to temperature changes or
changes in tire pressure from natural air leakage. If the system has not been
initialized recently, setting the tire pressures to factory specifications should
turn off the light.
The tire pressure warning system can be selected on “” of the multi-
J O G P S N B U J P O E J T Q M B Z . * %
System rest initialization
4 F M F D U “Vehicle Settings” and then push “” J O D I E J T Q M B Z
“” and then
push and hold “
w J O D I E J T Q M B Z
4 F M F D U i 5 1 8 4 w B O E U I F O Q V T I i
”.
4 F M F D U i 4 F U 1 S F T T V S F w U I F O Q V T I B O E I P M E i
” until the warning light blinks
three times.
Safety Connect is a subscription-based telematics service that uses Global
1 P T J U J P O J O H 4 Z T U F N ( 1 4
E B U B B O E F N C F E E F E D F M M V M B S U F D I O P M P H Z U P Q S P W J E F T B G F U Z
and security features to subscribers. Safety Connect is staffed with live agents at
the Toyota response center, which operates 24 hours per day, 7 days per week.
Services for subscribers include:
• Automatic collision notification
• Stolen vehicle locator
t & N F S H F O D Z B T T J T U B O D F i 4 0 4 w C V U U P O
• Enhanced roadside assistance
For additional information refer to the “Owner’s Manual” or visit www.Toyota.com/
connected-services.
Microphone
LED Indicators“SOS” button
4.2-inch display 7-inch display
Page 49 of 52
47
To begin the Bluetooth® Pairing process, press the HOME button on the faceplate of
your multimedia system.
Bluetooth® Pairing for your phone
Pairing your phone is the first step in connecting with your Toyota. This pairing
process is quick and easy. All you have to do is setup the phone and multimedia
system to form a connection.
1
Select "Bluetooth", then select
"Add New Device"on display
screen. Ensure Bluetooth is turned on for
your device.
Select "Device Name".
iPhone bluetooth MenuAndroid bluetooth Menu
1
Some Android devices may have slightly different SETTINGS screen layout depending on manufacturer of device and Android OS version.
Check the display on your smart
phone. Does the PIN XXXX
match the PIN displayed? If it
does select "Pair".
Press [MENU] on the audio system faceplate, then select "Setup" on display
screen.STEP 1
STEP 2
STEP 4
STEP 3
STEP 5
Audio / Audio Plus / Premium Audio
Page 50 of 52
48
BLUETOOTH® DEVICE PAIRING
Bluetooth® Pairing for your phone (cont.)
"Connecting" displays while
device is forming the connection
to your multimedia system. & O B C M F / P U J G J D B U J P O T U F Y U
N F T T B H F
8 I J M F Q B J S J O H Z P V S
phone a message will be
E J T Q M B Z F E
"You may need to allow
message access on your
phone".
/ P U F : P V N B Z B M T P T F M F D U
"Skip" on display screen to skip
enabling notifications. If skipped
proceed to
Step 8.
Turn on "Show Notifications" for
iPhone or "ON" for Android.A confirmation will appear once
your phone has been paired and
connected.
iPhoneAndroid
STEP 6
STEP 8
STEP 7
STEP 9