2020 TESLA MODEL 3 Owner's Manuals

Fluid Reservoirs
Removing the Maintenance Panel
To check

Topping Up Windshield Washer
Fluid
The only reservoir into which you can add

Jacking and Lifting
Jacking Procedure
Follow the steps below to lift Model 3. Ensure
that any non-Tesla repair facility is aware of
these lifting points.
1. Position Model 3 centrally between the lift
posts.
2. Position the lift arm pads under the
designated body lift points at the
locations shown.
Warning: DO NOT position the lift
arm pads under the Battery or side
rails, as shown in red.
3. Adjust the height and position of the lift
arm pads to ensure that they are correctly
located.
4. With assistance, raise the lift to the
desired height, ensuring the lift arm pads remain in their correct positions.
5. Engage any lift safety locks. Follow the lift
manufacturer

Parts and Accessories
Parts, Accessories, and
Modifications
Use only genuine Tesla parts and accessories.
Tesla performs rigorous testing on parts to
ensure their suitability, safety, and reliability.
Purchase these parts from Tesla, where they
are professionally installed and where you can receive expert advice about modifications to
Model 3. Accessories are available for
purchase from Tesla stores or online at www.tesla.com .
Note: Some accessories may not be available
in your market region.
Tesla is unable to assess parts manufactured
by other distributors and therefore accepts no responsibility if you use non-Tesla parts onModel 3.
Warning: Installing non-approved parts
and accessories, or performing non- approved modifications, can affect the
performance of Model 3 and the safety of
its occupants. Any damage caused by
using or installing non-approved parts, or by performing non-approved
modifications, is not covered by the
warranty.Warning: Tesla does not accept liability
for death, personal injury or damage that
occurs if you use or install non-approved
accessories or make non-approved
modifications.Accessory Wheels and Tires
If your Model 3 is fitted with Tesla accessory
wheels or tires, the Gross Axle Weight Rating
(GAWR), wheel, tire, and loading information
may be different from the labels shown on the
vehicle. Refer to the relevant following section
for updated information.
Note: If your vehicle is not fitted with Tesla
accessory wheels or tires (it is fitted with the
factory original wheels and tires, including
Tesla genuine replacement parts), refer to the
labels attached to the center door pillar for
the most accurate information for your Model 3.
20" Sport WheelsWheelsLocationWidth (in)Offset(mm)20"Front/Rear8.540Tires (front/rear)SizeTire
PressureMichelin, Pilot
Sport 4S (PS4S)235/35ZR2 042 PSI
(290 kPa)**Increase the tire pressure to 44 PSI (300
kPa) prior to driving 136 mph (220 kph) or faster.GAWRFront2407 lbs1,092 kgRear2,767 lbs1,255 kg
Parts and Accessories
Maintenance179

19" Sport WheelsWheelsLocationWidth(in)Offset(mm)19"Front/Rear8.540Tires (front/rear)SizeTire
PressureContinental,
ProContact RX235/40R1942 PSI
(290 kPa)*Hankook Ventus
S1 Evo3235/40R1942 PSI
(290 kPa)*Pirelli Winter
Sottozero 3235/40R1942 PSI
(290 kPa)*Increase the tire pressure to 44 PSI (300
kPa) prior to driving 134 mph (215 kph) or
faster.GAWRFront2,447 lbs1,110 kgRear2,767 lbs1,255 kg19" Gemini Wheels (Performance)
See Removing and Installing Aero Covers on
page 167 for information on how to remove
and install Gemini wheel covers.WheelsLocationWidth (in)Offset(mm)19"Front/Rear8.535Tires (front/rear)SizeTire
PressureHankook Ventus
S1 Evo3235/40R1942 PSI
(290 kPa)*Pirelli Winter,
Sottozero 3235/40R1942 PSI
(290 kPa)**Increase the tire pressure to 44 PSI (300
kPa) prior to driving 136 mph (220 kph) or faster.GAWRFront2510 lbs1,141 kgRear3,023 lbs1,374 kg
Parts and Accessories
180Model 3 Owner

18" Aero WheelsWheelsLocationWidth(in)Offset(mm)18"Front/Rear8.540Tires (front/rear)SizeTire
PressureMichelin, Primacy
MXM4235/45R1842 PSI
(290 kPa)Michelin, Pilot
Sport 4 (PS4)235/45R1842 PSI
(290 kPa)Pirelli Winter
Sottozero Serie II235/45R1842 PSI
(290 kPa)GAWRFront2,447 lbs1,110 kgRear2,840 lbs1,288 kgBody Repairs
If your Model 3 is in a collision, contact Tesla
or a Tesla-approved Body Shop to ensure that
it is repaired with genuine Tesla parts. Tesla
has selected and approved body shops that
meet strict requirements for training,
equipment, quality, and customer satisfaction.
Some repair shops and insurance companies
might suggest using non-original equipment or salvaged parts to save money. However,
these parts do not meet Tesla

1.Get isopropyl alcohol and test it on a non-
visible painted surface of your vehicle to
confirm that it does not damage or
remove the paint.
2. Clean the mounting site with isopropyl
alcohol and allow to dry for at least one
minute.
3. Fully remove the protective tape from the
adhesive at the top of the bracket and
partially remove the tape from the top of
the adhesive on each side. Leave the
bottom half of the tape on the sides in
place and fold the unattached tape
outward for easy removal after aligning
the bracket to the bumper.
4. While tilting the top of the license plate
bracket away from the bumper (to prevent adhering it to the wrong location),
align the bottom center of the license
plate bracket with the middle of the grille
as shown.
Note: Be as precise as possible when
aligning the bracket because you will be
unable to reposition it once adhered to
the bumper.
5. While correctly aligned, move the top of
the bracket against the bumper and applypressure so that it is held in place by the
adhesive.
6. Remove the remaining tape from the sides
of the bracket then press the entire
bracket firmly against the bumper,
ensuring the bracket is held in place by all
adhesive areas.
7. Once the bracket is securely mounted, use
the four supplied screws to attach your
license plate to the bracket (tighten to 3
Nm/2.2 ft-lbs).
Parts and Accessories
182Model 3 Owner

Specifications
Identification
Labels
Vehicle Identification Number
You can find the VIN at the following
locations: