2020 SUZUKI JIMNY display

OPERATING YOUR VEHICLE
TPMS malfunction indicator
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
The TPMS malfunction indicator is com­bined with the low tyre pressure telltale. When the system detects a malfunction, the telltale will flash for about 75 seconds and then remain continuously illuminated. This sequence will continue upon subse­quent vehicle start-ups as long as the mal­function exists.
The TPMS malfunction indicator is not reset even after the engine is turned off; it remains in the ON state until the normal conditions are restored.
When the malfunction indicator is illumi­nated, the system may not be able to detect or signal low tyre pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tyres or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction tell­tale after replacing one or more tyres or wheels on your vehicle to ensure the replacement or alternation of tyres and wheels to allow the TPMS to continue to function properly.
3-67
NOTICE
The tyre pressure sensors can be damaged if you do not take proper precautions.
We highly recommend that you have tyres repaired or replaced by a SUZUKI dealer. The tyre pressure sensors can be damaged by instal­lation or removal of tyres. • Do not use liquid sealants for a flat tyre unless your vehicle is equipped with a flat tyre repair kit instead of a spare tyre.
NOTICE
If the low tyre pressure warning light comes on frequently, there may be something wrong with one or more of the tyres, tyre pressure sensors or the monitoring system.
If the low tyre pressure warning light comes on frequently, have your vehi~ cle inspected by a SUZUKI dealer.
61MM0A199
NOTE: For a cerlain type of instrument cluster only, the information display shows the above warning and indicator message when this light comes on.

TPMS limitations
The tyre pressure monitoring system may not function properly under certain circum­stances. In the following situations, the low tyre pressure warning light may come on and remain on or may blink. When you replace a flat tyre with the spare tyre. When you include a spare tyre during a tyre rotation. When the TPMS sensor is damaged during a tyre replacement or liquid seal­ants are used to repair a flat tyre. When the electronic signal of TPMS sen­sor is disturbed in one of the following ways: -Electric devices or facilities using simi­lar radio wave frequencies are nearby. -A metallic film that may cause radio wave interference is attached on the window. -A lot of snow or ice covers the vehicle, in particular, around the wheels or wheel housings. -Snow tyres that are not installed with genuine TPMS sensors or snow chains are used.
When you use non-genuine SUZUKI wheels or tyres. When the pressure of any tyre is too high. When there is a problem with the receiver of the TPMS controller.
TPMS setting (For instrument clus­ter -Type A)
You can set one of the initial value of tyre pressure below that is indicated on the tyre information label. -Comfort Mode -Load Mode
For details on how to set the mode, refer to "Setting mode" in "BEFORE DRIVING" section.
A WARNING
If the loading weight has changed, adjust the tyre pressure according to the tyre information label and set the initial value via the information dis­play. If the loading weight, tyre pres­sure and initial value do not match, the tyre pressure monitoring system will not function properly.
OPERATING YOUR VEHICLE
TPMS setting (For instrument clus­
ter• Type B)
• You can check the current tyre pressure on the information display. • You can set one of the initial value of tyre pressure below that is indicated on the tyre information label. -Comfort Mode
-Load Mode
A WARNING
If the loading weight has changed, adjust the tyre pressure according to the tyre information label and set the initial value via the information dis­play. If the loading weight, tyre pres­sure and initial value do not nJatch, the tyre pressure monitoring system will not function properly.
3-68

OPERATING YOUR VEHICLE
To check the current tyre pressure
(1)
78RB03016
1) When the ignition switch is turned to "ON" and the vehicle is stationary, push and hold the indicator selector knob (1) on the instrument cluster for a while to change the information display to the setting mode.
Setting mode
78RB03017
3-69
2) Turn the indicator selector knob (1) left or right to select "TPMS" and push the indicator selector knob.
NOTE: If you exit the setting mode, select "Back" and push the indicator selector knob (1 ).
TPMS
78RB03018
3) Turn the indicator selector knob (1) left or right to select "Tyre Press" and push the indicator selector knob.
78RB03019
4) The display shows current tyre pres­sure. NOTE: If the low tyre pressure warning light comes on, the information display will be switched to "Tyre Press" display and the corresponding tyre pressure indication blinks to alert you which tyre(s) is(are) low pressure. The display may not show the tyre pres­sure for about 10 minutes after the vehi­cle begins to move. This is because the TPMS system learns the tyre pressure within this 10 minutes. The display will show the tyre pressure after 10 minutes pass.

If you stop the vehicle and turn the igni­tion switch to "LOCK" position, and leave it for 20 minutes or more, tyre pressure wi/1 be reset and will be indicated as 0 kPa when the engine is restarted. In this case, the current tyre pressure indication will recover after driving for a while. However, if any of tyre pressures has been detected as low pressure before stopping the engine, the tyre pressure indication may not recover and may be indicated as "---".
To set the initial value of tyre pressure
(1)
78RB03016
1) When the ignition switch is in "ON" position and the vehicle is stationary, . push and hold the indicator selector knob (1) on the instrument cluster for a while to change the information display to the setting mode.
OPERATING YOUR VEHICLE
78RB03017
2) Turn the indicator selector knob (1) left or right to select "TPMS" and push the indicator selector knob.
NOTE: If you exit the setting mode, select "Back" and push the indicator selector knob (1 ).
3-70

OPERATING YOUR VEHICLE
78RB03018
3) Turn the indicator selector knob (1) left or right to select "TPMS Mode" and push the indicator selector knob.
78R803020
3-71
4) Turn the indicator selector knob (1) left or right to select the initial value and push the indicator selector knob.
78RB03021
5) When the display shows the message shown in the above illustration, the set­ting is completed.
Replacing tyres and/or wheels
If you got a fiat tyre and replaced it with the spare tyre, SUZUKI recommends that you have a SUZUKI dealer mount a new tyre on the wheel that had the fiat tyre. The TPMS is already set up to recognize the ID code of the original wheel, and normal TPMS operation will be restored.
If you need to replace any wheels on your vehicle, a SUZUKI dealer must check that TPMS sensors are installed in the new wheels and must set up the TPMS to rec­ognize the new sensors.
NOTE:
A TPMS sensor is not installed in the spare tyre. You should use the spare tyre only in an emergency situation, and should replace the spare tyre as soon as possible to restore normal TPMS operation.
A WARNING
Use of tyres or wheels not recom­mended by SUZUKI can result in fail­ure of the TPMS.
When replacing tyres and wheels, use only tyres and wheels recom­mended by SUZUKI as standard or optional equipment for your vehicle. Refer to "tyres" in "INSPECTION AND MAINTENANCE" section for addi­tional information.

OTHER CONTROLS AND EQUIPMENT
Automatic heating and air conditioning system
{climate control)
Description of controls
(5) (4) (9) (7) (8)
MODE OFF
'm' 0 fR """""" --------~ -AIC
(2) (3) (6) (1)
5-23
78RB05036
(1) Temperature selector (2) Blower speed selector (3) Air intake selector (4) Airfiow selector (5) Defrost switch (6) Air conditioning switch (7) "OFF" switch (8) "AUTO" switch (9) Display

Temperature selector (1)
0
~= 0
-A/C
Turn the t 1aRsoso31
the tempe~:R~;',;ature selector (1) to adjust
NOTE: ff you turn the t until "HI" or "LO" emperature selector (1)
the climate controf'ii,~r::n on'fre display, maximum heatin . WI operate at ture of the air fro;,,o;hcoofmg. The tempera­
suddenly while "LO"eo~~!t/~ _ma~ change but this is normal. is displayed,
NOTE: When you change th . in the information di/ unit of temperature
perature in the air coh1f the unit of tern­be changed. Refer t " I ionmg _system will m the "BEFORE o Information display" details. DRIVING" section for
OTHER CONTROLS AND EQUIPMENT
Blower speed selector (2)
The blower s eed raRsoso3s turn on the 6iowe seledctor (2) is used to speed. r an to select blower
If "AUTO" switch (8) · speed will vary aut ,s P~_shed, the blower mate control s oma ,cally as the cli­
selected temperatCr~~m maintains the
Air intake selector (3)
Push the air intake s raRsoso39 between the recircul;;le~tor (3) to change mode. e air and fresh air
If "AUTO" switch (8) · intake will vary autom i5 flushed, the air control system main!} ,ca,hy as the climate perature. ins e selected tem-
NOTE: When the reci I selected, the aut~~ ated air . mode is is deactivated even at;" operaflon system switch (8). 1 you push "AUTO"
5-24

OTHER CONTROLS AND EQUIPMENT
RECIRCULATED AIR (a) When this mode is selected, outside air is shut off and inside air is recirculated. This mode is suitable when driving through dusty or polluted air such as a tunnel, or when attempting to quickly cool down or warm up the interior.
FRESH AIR (b) When this mode is selected, outside air is introduced.
FRESH AIR and RECIRCULATED AIR are selected alternately each time the air intake selector is pushed.
NOTE: If you select RECIRCULATED AIR for an extended period of time, the air in the vehi­cle can become contaminated and the win­dows tend to get misted. Therefore, you should select FRESH AIR whenever possi­ble.
5-25
Air flow selector (4)
(c) ~
!
(d) •~
!
(e) •,J
!
(f) 'f,;
8
~-ffi
78RB05040
Push the air fiow selector (4) to change among the following functions. The indica­tion of the selected mode appears in the display.
If "AUTO" switch (8) is pushed, the air fiow will vary automatically as the climate con­trol system maintains the selected tem­perature.
VENTILATION (c)
... ,.,
78RB05041
Temperature-controlled air comes out of the canter and side outlets.