2020 SUBARU BRZ Quick Guide

AUDIO CONTROLS
1Source
2Volume Up
3Volume Down
4Preset Skip
5Phone Send
6Phone End
MULTI-INFORMATION DISPLAY CONTROL
1Return
2Scroll Up/Down
3Scroll Left/Right
4Enter
5Voice Recognition
CONTROLS
15

CRUISE CONTROL
1RES:To resume your speed after
canceling, push the lever up to the “RES”
side.
2CANCEL:To cancel the cruise control,
pull the lever toward you, push the brake
pedal or press the “ON-OFF” button. If
you have a manual transmission, you can
push in the clutch pedal.
3SET:Press the accelerator pedal until your vehicle reaches the desired speed. Push
the lever down to the “SET” side and release. Ease off the accelerator pedal. Your
vehicle will maintain the desired speed.
4ON/OFF:To activate the cruise control, press the “ON-OFF” button. The cruise
control indicator light on the instrument panel will turn on. To deactivate cruise
control, press the “ON-OFF” button again.
Increase speed
Push the lever up to the “RES” side; hold until your vehicle reaches the desired speed and
release. To increase speed using the accelerator pedal, press the pedal until you reach the
desired speed. Push the lever down to the “SET” side to set the speed.
Decrease speed
Push the lever down to the “SET” side; hold until your vehicle slows to the desired speed
and release. To decrease the speed using the brake pedal, press the pedal to release
cruise control temporarily. When the speed decreases to the desired speed, push the lever
down to the “SET” side to set the speed.
LIGHT CONTROLS
1AUTO:If equipped, rotate the end of the
lever to automatically turn your headlights
on or off, depending on the level of
outside light.
2Daytime Running Lights:Rotate the end
of the lever to turn on the instrument
panel lights, parking lights, side marker
lights, tail lights, and license plate lights.
3Headlights:Rotate the end of the lever to
turn on the headlights, instrument panel
lights, parking lights, side marker lights,
tail lights, and license plate lights.
CONTROLS
16

4High Beams:Push the lever forward to change from low beam to high beam. Pull the
lever back to center to return to low beam. If equipped, this also activates the High
Beam Assist (HBA) system.
5Fog Lights:If equipped, rotate the dial to turn on the fog lights.
Illumination Brightness
While the light switch is on, rotating the dial on
the instrument panel upward will make the
illumination brighter. When the dial is fully
rotated upward (dots aligned), the instrument
panel illumination stays at full brightness.
Rotating the dial downward dims the
instrument panel illumination.
For map equipped vehicles this setting also
affects the day/night view and illumination
level.
Daytime Running Lights
The daytime running lights automatically turn on when the engine has started, the parking
brake is fully released, the light switch is in the Off, “AUTO” (if equipped) or “
”
position, and the select lever is not in the “P” position. Always turn on the headlights when
it’s dark outside by rotating the dial to the “
” or “AUTO” position.
TURN SIGNALS
Push slightly up for right lane change or fully
up for right turn signal. Push slightly down for
left lane change or fully down for left turn
signal.
CONTROLS
17

WINDSHIELD WIPERS
To turn on the wipers, press the wiper control
lever down one position for intermittent, two
positions for low speed, or three positions for
high speed. To turn the wipers off, return the
lever to the “OFF” position. For a single wipe,
move the lever up one position.
When the lever is in the intermittent position,
rotate the dial to adjust the operating interval
of the wipers.
Pull the lever toward you to spray washer fluid. The washer will spray until you release the
lever, then wipe twice.
INSTRUMENT PANEL SWITCHES(LOWER LEFT)
1Illumination brightness control (p. 17)
2Trunk Release (p. 26)
km/h - MPH, ODO - TRIP and DISP Buttons
There are three buttons to the left of the
instrument cluster to change the display.
1km/h – MPH:Press this button to change
the digital display from km/h to MPH.
Press again to switch back.
2ODO – TRIP:Press this button to cycle
through the odometer, trip meter A, trip
meter B, the setting screen for the
tachometer needle or the setting screen
for the shift position indicator.
3DISP:For BRZ Premium, press this button to cycle through the outside temperature,
current fuel consumption or average fuel consumption.
CONTROLS
18

OVERHEAD PANEL
1Interior Light Switch
2Light
CONTROLS
19

GAUGES
1Tachometer
2Speedometer
3Digital Speedometer
4Fuel gauge
5Multi-Information Display
WARNING AND INDICATOR LIGHTS
Red lights indicate immediate attention is required. Some examples are:
Seatbelt
warningDoor
openBrake system
Yellow lights indicate caution. Some examples are:
Low fuelEngine oil
level warning
lightTire pressure
warning light
Green and blue lights are for information. Some examples are:
Headlight
indicator
lightCruise
ControlHigh beam
indicator
light
GAUGES AND WARNING LIGHTS
20

PUSH-BUTTON IGNITION SWITCH
Each time you press the ignition switch
without depressing the brake pedal, the
ignition position will change as follows: ACC,
ON, OFF.
ACC (Accessory):Provides power to the radio
and accessory power outlets. Orange indicator
illuminates.
ON:All electrical systems will be available.
Orange indicator illuminates.
OFF:Power off and indicator off.
STARTING THE ENGINE
With Push-button Ignition
To start the engine:
1. Sit in the driver’s seat with the access key fob.
2. Make sure the select lever is in the “P” position or “N” for manual transmission vehicles.
3. Depress the brake pedal (and clutch pedal for manual transmission models).
4. While depressing the brake pedal (and clutch pedal for manual transmission models),
briefly press and release the ignition switch.
DRIVING THE VEHICLE
6-Speed Manual Transmission
This manual transmission is a fully
synchronised 6-forward and 1-reverse speed
transmission. Before you can shift into reverse
gear, you must raise the slider ring and hold it
in that position. Only pull the slider ring up
when shifting into reverse gear.
OPERATING THE VEHICLE
21

Automatic Transmission Shift Mode(if equipped)
The transmission is electronically controlled
and provides two different driving modes:
normal and manual.
Normal Mode
When the select lever is in the “D” (Drive)
position, the transmission is in normal shift
mode. The select lever position indicator in the
Combination Meter Display (CMD) shows “D”
and the transmission automatically shifts into a
suitable forward gear.
Manual Mode
In manual mode, you select the desired gear
position to obtain necessary acceleration and engine braking. Move the selector lever left
from the “D” position into the “M” position to select manual mode. The gear position
indicator in the Combination Meter Display (CMD) shows the currently selected gear.
Arrow-shaped indicators show when upshifting or downshifting is available. To shift, use
the paddle shift control switches behind the steering wheel.
Paddle Shift Control Switches
• You can shift gears using the paddle shift control
switches. To upshift to the next higher gear, pull the
“+” paddle on the right toward you. To downshift to
the next lower gear, pull the “–” paddle on the left
toward you.
• You can temporarily shift gears even when the
selector lever is in the “D” position by pulling either
the “+” or “–” paddle toward you. Once vehicle
speed stabilizes, the transmission will switch back to normal mode.
OPERATING THE VEHICLE
22