2020 Seat Tarraco light

Driving
Automatic gearbox/DSG au-
t omatic gearbo
x*
Introduction Your vehicle is equipped with an electronical-
ly contr
oll

ed manual gearbox. Torque be-
tween the engine and the gearbox is trans-
mitted via two independent clutches. They
replace the torque converter found on con-
ventional automatic gearboxes and allow for
smooth, uninterrupted acceleration of the ve-
hicle.
The Tiptronic system allows the driver to
change gears manually ››› page 230,
Changing gear in Tiptronic mode*.
Control lamps 
It lights up green
The brake is not pressed.
T o sel

ect a gear range, press the brake pedal. 
Flashes green
The selector lever locking button is not engaged.
The v ehicl

e is prevented from moving forwards. En-
gage the selector lever lock. Selector lever positions
Fig. 166
Selector lever lock. Fig. 167
Selector lever lock (hybrid vehicles). The selector lever position is shown when the
corr
esponding sign lights up

. With the selec-
tor lever in the manual gearbox positions M, D
and S, the engaged gear is also shown on the
display. 
– Parking l
ock
When the lever is put in this position, the drive
wheels are locked. The lever must only be put
in P when the vehicle is stationary ››› .
T o put the l

ever in P or take it out of P , the
locking button must be pressed and held and
the brake pedal pressed simultaneously.
 – Reverse gear
Reverse gear must be engaged only when
the vehicle is stationary and the engine is
idling ››› .
T o mo

ve the lever to position R, the lock but-
ton must be pressed and held while pressing
the brake pedal at the same time. The reverse
lights come on when the lever is in the R posi-
tion with the ignition on.
 – Neutral
With the lever in this position, the gear is in
neutral.
Press the brake pedal to move the lever from
N to D/S when the vehicle is stationary or at
speeds below 3 km/h (2 mph) ››› .
 – P
ermanent f

orward drive position
The lever in the D/S position enables the
gears to be operated in normal mode (D) or
sport mode (S). To select Sport mode S,
move the lever backwards. Pushing the lever
again will select normal mode D. The
228

Driving
k
It lights up grey
Hill Descent Control is not active. The system is
s wit
ched on, but is not adjusting. Some control and warning lamps will light up
briefly when the ignition is s
wit

ched on to
check certain functions. They will switch off
after a few seconds. WARNING
Observe the safety warnings ››

› in Con-
tr ol and w
arning lamps on page 85. Description and operation
Hill Descent Control limits the speed on steep
descents by aut
omatically br

aking all four
wheels, both when moving forward and in re-
verse. As the anti-lock brake system remains
active, it prevents the wheels from locking. In
vehicles with manual transmission, the Hill
Descent Control adapts the theoretical
speed without slowing the engine below its
idling speed.
After starting the descent of a slope below
30 km/h (18 mph), speed is limited to a mini-
mum of 2 km/h (1 mph) and a maximum of
30 km/h (18 mph). When appropriate, the
driver may increase or decrease the speed
within the limit by pressing the accelerator or the brake. At this point the function is interrup-
ted and, if necessary, it is then r

eactivated.
Even so, it is imperative that the surface guar-
antees sufficient adhesion. For this reason,
the Hill Descent Control will not fulfil its func-
tion when, for example, descending a slope
with a frozen or slippery surface.
Hill Descent Control is available when the
dash panel display shows the message k .
Hill Descent Control automatically intervenes
if the following conditions are met:

Start and driving
sportier, more direct and noticeably more dy-
namic driving sensation.
St eering assist
This help assists the driv
er in critical situa-
tions. It recommends turning the steering
wheel to perform a corrective manoeuvre
(counter-steering), turning slightly to avoid
skidding ››› .
WARNING
Steering assist helps the driver in critical
sit uations. The driv

er is the person who has
to control the vehicle's steering at all times. Control lamp
v
It lights up red
Faulty steering.
Do not continue driving, st op the v

ehicle as soon as
possible and in a safe manner.
Take the vehicle to a specialised workshop and have
the fault repaired as soon as possible. v
It lights up yellow
Limited steering operation.
Driv e car

efully to a specialised workshop to have the
steering checked.
If the warning light does not come on again after re-
starting the engine and driving a short distance, it is
not necessary to check the steering.
OR: The 12-v olt batt
ery was disconnected and re-
connected.
Drive a short distance at 15-20 km / h (9-12 mph). v
It flashes yellow
The steering column is jammed.
When st opped, t

urn the steering wheel in both direc-
tions.
OR: The st eering column does not unlock or lock.
T
urn off the ignition and turn it on again. Consider the
messages shown on the instrument panel display.
Do not continue driving if the steering column re-
mains locked after switching on the ignition. Seek
specialist assistance. The control lamp should light up for a few
seconds when the ignition is s
wit

ched on. It
should go out once the engine is started. WARNING
Never ignore the warning lamps or messag-
es.

Driving
adhesives, additional headlights or similar
it
ems, as this coul
d have a negative impact
on the operation of the assistants. If the ve-
hicle is not properly repaired or structural
modifications are made to it, the operation
of the assistants may be affected.

Driver assistance systems
unavailable or ACC unavailable warning
lights come on.

Driving
The control lamps light up when the ignition is
s wit
ched on and should turn off after approxi-
mately 2 seconds. This is the time taken for
the function check.
If there are no indications from the control
lamp of the lane departure warning, this
means that the lane departure warning has
not detected any other vehicles at the rear
area ››› .
When the e xt

erior lighting is low, the intensity
with which the control lamps come on is dim-
med. The user can modify the intensity of the
control lamps with up to 5 levels in the info-
tainment system menu. WARNING
If the warning lamps and the corresponding
messages ar e ignor

ed when they light up,
the vehicle may stall in traffic and cause
accidents and severe injuries.

Braking and parking
camera, it can also be accessed by means of
the driv er assist
ance systems key located on
the main beam headlight lever.
Open the Assistants menu.

Driving
Brake blending 1)
The br ak
e energy recuperation can generate
a braking effect. This braking effect depends
on the selected driving programme and the
level of charge of the high-voltage battery.
If the braking effect caused by the recupera-
tion is very intense, the vehicle’s brake lights
with turn on. The electric engine, when oper-
ating as an alternator, can generate braking
torque on the front wheels based on the RPM
and the temperature and charge level of the
high-voltage battery.
These variable parameters cause fluctuating
electric decelerations which are hydraulical-
ly compensated according to the driver’s de-
sires. This function is called “brake blending”
and it combines mechanical braking with the
engine brake effect. WARNING
Driving at high speed on icy, slippery wet
gr ound can r

esult in loss of vehicle control
and serious injury to the driver and passen-
gers.