2020 Seat Leon warning light

Operation
Opening and closing Set of v ehicl
e keys
Vehicle key Fig. 80
Vehicle key Fig. 81
Centre console: vehicle key socket. Key to the
››

› Fig. 80
Unlock the vehicle
1 Lock the vehicle
Unl
ock only the r

ear lid. Press the button
until all the turn signals on the vehicle
flash briefly. You have 2 minutes to open
the rear lid. Once this time has passed, it
will lock again. In addition, the lamp on
the key flashes.
Control lamp
Alarm button*. Only press in the event of
an emergency! When the alarm button is
pressed, the vehicle's sounds and the turn
signals light up for a short time. Press
again to disconnect.
With the vehicle key the vehicle may be
locked or unlocked remotely ››› page 101
.
The vehicle key includes an emitter and bat-
tery. The receiver is in the interior of the vehi-
cle. The range of the vehicle key with remote
control and new battery is several metres
around the vehicle.
If it is not possible to open or close the vehicle
using the remote control key, this should be
re-synchronised ››› page 100
or the battery
changed ››› page 100
.
Different keys belonging to the vehicle may
be used.
Control lamp on the vehicle key
When a button on the vehicle key is briefly
pressed, the indicator lamp flashes 4 ›››
Fig. 80 once briefly, but if the butt
on is
2 3
4
5 held down for a longer period it will flash sev-
er
al times, such as f
or convenience opening.
If the vehicle key control lamp does not light
up when the button is pressed, replace the
key's battery ››› page 100
.
Key socket*
Depending on the version there is a socket for
the key close to the start button ››› Fig. 81
.
Warning! Do not confuse with the location for
the emergency start ››› page 222
.
Spare key
To obtain a spare key and other vehicle keys,
the vehicle ID number is required.
Each new key contains a microchip which
must be coded with the data from the vehicle
electronic immobiliser. A vehicle key will not
work if it does not contain a microchip or the
microchip has not been encoded. This is also
true for keys which are specially cut for the
vehicle.
The vehicle keys or new spare keys can be
obtained from a SEAT Official Service, a spe-
cialised workshop or an approved key service
qualified to create this kind of key.
New keys or spare keys must be synchronised
before use ››› page 100
.
98

Lights
WARNING
Improper or lack of use of the turn signals,
or f or
getting to deactivate them can con-
fuse other road users. This could result in a
serious accident.

Operation
7. Always take the vehicle key with you when you l eav
e the vehicle.
All turn signals flash simultaneously when the
hazard warning lights are switched on. The
two turn signal turn signal lamps   and the
turn signal lamp in the switch  will flash at
the same time. The simultaneous hazard
warning lights also work when the ignition is
switched off.
Emergency braking warning
If the vehicle brakes suddenly and continu-
ously at a speed of more than 80 km/h (50
mph), the brake light flashes several times per
second to warn the vehicles driving behind. If
you continue braking, the hazard warning
lights will come on automatically when the
vehicle comes to a standstill. They switch off
automatically when the vehicle starts to
move again. WARNING

Operation
USB power sockets
Depending on the equipment and the coun-
try, the v ehicl
e may also have USB connec-
tions exclusively for charging or as a power
socket.
These USB ports are located at the rear of
the console, between the front seats . These
connectors can work at a maximum power of
up to 10.5 W per port.
They are not intended for file playback.
230 volt power socket*
With the engine running, the power socket
››› Fig. 148 activates automatically as soon
as a connector is plugged in. If there is
enough power available, the socket can still
be used while the engine is off ››› Connect an electrical device: Open the co
v-
er and insert the plug int
o the power socket
as far as possible to unlock the built-in child
lock. The socket only supplies power once
the child lock is unlocked. LED on the power socket
Steady green
light: The childproof lock is unlocked.
The sock
et is r

eady to operate. LED on the power socket
Flashing green
light: The ignition is switched off, but
ther
e is enough po

wer available
to continue supplying the socket
with current for a maximum of 10
minutes. If the connector is un-
plugged before this time elap-
ses, the socket is disconnected
and cannot be used again until
the ignition is switched on again.
Flashing red
light: There is an anomaly, e.g. dis-
connection due t
o a curr

ent
surge or overheating. Disconnection due to overheating
When the t
emper

ature exceeds a certain val-
ue, the 230 volt socket inverter is automati-
cally disconnected. The disconnection pre-
vents overheating when the power consump-
tion of the connected devices is excessive or
the ambient temperature is very high. The
230-volt power supply can be used once
again after a cooling time. First unplug the
connector of the connected device and then
plug it back in again. This prevents the elec-
trical device from being switched on again if
this is not wanted. WARNING
The electrical system is under high voltage!

Driving
level. The rest is kept until the end of the
journey.
The Int elligent Hybrid
App allows the user to
save electrical energy until reaching home
(charging point) with just “one click”. If this
option is not selected, the maximum amount
of electrical energy will be consumed until
the selected destination is reached. If the
user has no active route, the function will offer
the activation of a predictive route and BMA
mode from the widget itself with just one
click.
Show the active operating mode
The operating mode active at any given time
is displayed on the instrument cluster display,
e.g. B. WARNING
Switching to a different operating mode
whil e driving can distr

act you from traffic
conditions and cause accidents. Note
Information about the operating mode that
is curr ently activ

e is displayed on the in-
strument cluster display, along with the
charge level of the high-voltage battery. Troubleshooting
@
The E-MODE oper
ating mode is not
av
ailable
The indicator lamp lights up in white.
The E-MODE operating mode N (driving in
electric mode) cannot be used temporarily
because one or more conditions are not met.

Driving
 – P
arking l ock
When the P button is pressed, the drive
wheels are locked. Only press P when the ve-
hicle is stationary ››› .
T o pr

ess the P button you must press the
brake pedal simultaneously.
 – Reverse gear
Reverse gear must be engaged only when
the vehicle is stationary and the engine is
idling ››› .
T o engage r

everse gear R, you must press the
brake pedal simultaneously. The reverse
lights switch on when the reverse gear R is
selected and the ignition is on.
 – Neutral
In this position, the gear is in neutral.
Press the brake pedal to move the lever from
N to D/S when the vehicle is stationary or at
speeds below 3 km/h (2 mph) ››› .
 – P
ermanent f

orward drive position
The D/S position enables the gears to be op-
erated in normal mode (D) or sport mode (S).
To select Sport mode S, move the lever back-
wards. Pushing the lever again will select nor-
mal mode D. The selected driving mode is
displayed on the instrument panel screen.
In normal mode (D), the gearbox selects the
best gear ratio. This depends on the engine load, the road speed and the dynamic gear
control pr

ogramme (DCP).
Sport mode (S) should be selected for a
sporty driving style. This setting makes use of
the engine's maximum power output. When
accelerating the gear shifts will be noticea-
ble.
Under certain circumstances (e.g. on moun-
tain roads) it can be advantageous to switch
tiptronic mode ››› page 231
, to adapt the
gears to suit the road conditions.
Selector lever lock
In N, the lever lock prevents a gear range
from being engaged, and prevents the vehi-
cle from moving off accidentally.
Press and hold the brake pedal with your left
foot with the engine running.
As a reminder to the driver, when the lever is
in position N the following indication will be
shown on the screen:
When stationary, apply footbrake
while selecting a gear.
The lever is not locked if it is moved quickly
through position N (e.g. when shifting from R
to D). This makes it possible, for instance, to
“rock the vehicle backwards and forwards” if
it is stuck in snow or mud. The lever lock en-
gages automatically if the brake pedal is not
pressed and the lever is in position N for more than about one second at a speed of less
than 5 km/h (3 mph). WARNING

Driving
Steering Inf ormation r
elating to different ve-
hicle processes. Electro-mechanical power steering adapts
el
ectr

onically to the speed of the car, torque
and steering angle.
Even if the power steering fails or the engine
is stopped, it is possible to continue to rotate
the steering wheel as long as the key remains
in the ignition, but more force must be ap-
plied.
Progressive steering
Depending on the vehicle’s features, it may or
may not incorporate a progressive steering
system.
In city traffic you do not need to turn so much
on parking, manoeuvring or in very tight turns.
On the road or on the motorway, progressive
steering transmits, for example, in bends, a
sportier, more direct and noticeably more dy-
namic driving sensation. Control lamp v
It lights up red
Faulty steering.
Do not continue driving, stop the v
ehicle as soon as
possible and in a safe manner.
Take the vehicle to a specialised workshop and have
the fault repaired as soon as possible. v
It lights up yellow
Limited steering operation.
Driv e car

efully to a specialised workshop to have the
steering checked.
If the warning light does not come on again after re-
starting the engine and driving a short distance, it is
not necessary to check the steering.
OR: The 12-v olt batt
ery was disconnected and re-
connected.
Drive a short distance at 15-20 km / h (9-12 mph). v
It flashes yellow
The steering column is jammed.
When st opped, t

urn the steering wheel in both direc-
tions.
OR: The st eering column does not unlock or lock.
T
urn off the ignition and turn it on again. Consider the
messages shown on the instrument panel display.
Do not continue driving if the steering column re-
mains locked after switching on the ignition. Seek
specialist assistance. The control lamp should light up for a few
seconds when the ignition is s
wit

ched on. It
should go out once the engine is started. WARNING
Never ignore the warning lamps or messag-
es.

Driving
Note
If the lane departure warning with rear
cr oss tr
affic alert does not work as descri-
bed in this chapter, stop using it and con-
tact a specialised workshop. Control lamp
Fig. 188
Control lamp of the lane departure
w arning. Fig. 189
Control lamp of the lane departure
w arning. It lights up
It turns on once briefly: the lane departure warning is
activ at

ed and ready to operate, i.e. when activating
the system.
It lights up continuously: the lane departure warning
has det ect

ed a vehicle in the blind spot. Flashes
A vehicle has been detected in the adjacent lane and
the t urn signal has been engaged in the dir

ection of
the detected vehicle