2020 MITSUBISHI OUTLANDER ECO mode

Seat belt use during pregnancy 4-26 Seat and restraint systems
4
N00406800134
Seat belts work for
everyone, including preg-
nant women. Like al
l occupants, pregnant
women are more likely to be seriously injuredor killed in an accide
nt if they do not wear
seat belts.
N00417701710
The driver’s and front passenger’s seats each have a seat belt equippe
d with a pre-tensioner
system and force limiter system.
The driver and front pa
ssenger seat
belts are
equipped with a seat
belt pre-tensioner sys-
tem. In a moderate-to-severe frontal or sidecollision or when a rollover or overturning of the vehicle is detected
, the pre-tensioner sys-
tem operates simultane
ously with the deploy-
ment of the front airb
ags, side airbags or
curtain airbags. The seat belt pre-tensioners are located in the driver’s and front passe
nger’s seat belt retrac-
tors (A) and in the front passenger seat’s finalanchor (B). When activated, the pre-tension- ers quickly draw back seat belt webbing and increase seat belt performance. The seat belt pre-tensioner system includes the following components:
The airbag control unit monitors the readiness of the electronic parts of the system whenever the ignition switch or the operation mode is under the following condi
tions. These include
all of the item
s listed above a
nd all related
wiring. [Except for vehicles equipped with theF. A . S . T. - k e y ] The ignition switch is in the “ON” or “START” position. [Vehicles equipped with the F.A.S.T.-key] The operation mode is in ON.
Seat belt use during preg- nancy
WA R N I N G To reduce the risk of serious injury or death to pregnant women and unborn children in an accident, pregnant womenshould always wear
a seat belt. The lap
portion of the seat belt should be worn snug and low across the hips and belowthe rounding. Consult your doctor if you have any additional qu
estions or concerns.
Seat belt pre-tensioner and force limiter systems
Pre-tensioner system
1- SRS warning light 2- Front impact sensors 3- Seat belt pre-tensioner 4- Airbag control unit5- Side impact sensors 6- Seat belt buckle switches
BK0278200US.book 26 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Supplemental Restraint System (SRS) - airbag 4-36 Seat and restraint systems
4
the driver and the passengers on the front seat and the second row outboard seats with pro-tection against head in
juries by deploying the
curtain airbag on the side impacted in moder- ate to severe side im
pact collisions and by
deploying both curtain airbags when a roll- over is detected. The curtain airbags are also designed to help reduce the risk of completeand partial ejection from the vehicle through side windows in both side impact and roll- over type accidents. The SRS airbags are NOT a substitute for use of the seat belts. For maximum protection in all types of accident
s, seat belts must
ALWAYS be worn by everyone who drives or rides in this vehicle (with infants and small children in an appropriate child restraint sys-tem in the rear seat, and older children buck- led in the rear seat). Refer to “Child restraint systems” on page 4-27.
WA R N I N G IT IS VERY IMPORTANT TO ALWAYS WEAR YOUR SEAT BELT PROPERLYEVEN WITH AN AIRBAG.• Seat belts help keep the driver and pas-sengers properly positioned. Thisreduces the risk of injury in all collisions, and reduces the risk of serious injuries or death when the airbags inflate.During sudden braking just before a col- lision, an unrestra
ined or
improperly
restrained driver or front passenger canmove forward into direct contact with, or within close proximi
ty to, the airbag
when it begins to inflate.The beginning stage of
airbag inflation is
the most forceful and can cause serious injuries or death if the occupant comes incontact with the airbag at this time.• Seat belts reduce the risk of injury inrear impact collisions, and in lower- speed frontal collisions because the air- bags are not designed to inflate in thosesituations.• Seat belts reduce the risk of beingthrown from your vehi
cle in a collision or
rollover.
WA R N I N G IT IS VERY IMPORTANT TO BE PROP- ERLY SEATED.• A driver or front passenger sitting too close to the steering wheel or instrument panel during airbag deployment can beseriously injured or killed.• Airbags inflate very quickly and withgreat force. If the driver and front pas- senger are not properly seated and restrained, the airbag may not providethe proper protection, and can cause serious injuries or death when it inflates.• To reduce the risk to the driver of seriousinjury or death due to a deploying driver’s airbag, al
ways properly wear
your seat belt and adjust the driver’s seat as far back as possible, maintaining a position that still allows the driver tohave good control of the steering wheel, brake, accelerator,
and other vehicle con-
trols.• To reduce the risk to the front passengerof serious injury or
death from a deploy-
ing passenger’s airbag, make sure the passenger always wears the seat belt properly, remains seat
ed upright and all
the way back in the
seat, and positions
the seat as far back as possible.• Seat all infants and children in the rearseat, properly restrain
ed in an appropri-
ate child restraint system.
BK0278200US.book 36 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Supplemental Restraint System (SRS) - airbag 4-40 Seat and restraint systems
4
N00418101391
The passenger’s airbag off indicator is located as shown in
the illustration.
The indicator normally comes on when the ignition switch is turned to the “ON” position or the operation mode is put in ON, and goesout a few seconds later.
In the following situ-
ations, the indicator will stay on to show that the passenger front airb
ag is not operational.
 The front passenger’s seat is not occupied.  The system senses that a child is using a child restraint system on the front passen- ger’s seat.
When the passenger’s seat occupant classifi- cation sensor sy
stem sense there is a person
seated in the front passenger’s seat, the indi- cator goes out to show that the passenger’sfront airbag is operational.
• The SRS warning light does not initially come on when the ignition switch or theoperation mode is under the followingconditions. [Except for vehicles equipped with the F. A . S . T. - k e y ]The ignition switch is in the “ON” or “START” position. [Vehicles equipped with the F.A.S.T.-key]The operation mode is in ON.• The SRS warning light does not go outafter several seconds.• The SRS warning li
ght comes on while
you are driving.
 To ensure that the passenger’s seat occu- pant classification sensor system can sense correctly, observe the following instruc- tions. Failure to follow these instructionscan adversely affect
the performance of
the passenger’s airbag system.• Adjust the seat to the correct position,and sit well back
against the seatback.
Refer to “Front seats” on page 4-4.• Do not recline the seatback more thannecessary.• Never have more than one person (adultor child) sitting
on the seat.
• Do not place anything between the seat and the floor console.• When attaching a chil
d restraint system,
secure it firmly.• Do not place luggage or other objects onthe seat.WA R N I N G
• Do not use a seat cover or a cushion.• Do not modify or re
place the seat and
seat belt.• Do not place luggage or other objectsunder the seat.• Do not place and use
an electronic device
such as a computer on the seat.• Do not place heavy obje
cts on the seat or
stick pins, needles, or other objects into it.• Do not remove the seat cushion skin.• If any liquid is spille
d on the seat, wipe it
and dry the seat immediately.
 If the vehicle is involved in a severe impact, have the SRS sensors inspected by an authorized
Mitsubishi Motors dealer as
soon as possible.WA R N I N G
Passenger’s airbag off indicator
BK0278200US.book 40 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

5
Features and controlsECO mode switch ........................................................................ 5-209 Front fog light switch (if so equipped) ......................................... 5-209 Wiper and washer switch ............................................................ 5-210Wiper deicer switch (if so equipped)............................................ 5-215 Electric rear window def
ogger switch ......
...........
...........
............. 5-216
Heated steering wheel switch (if so equipped)............................. 5-217Horn switch ................................................................................. 5-218 Link System ................................................................................. 5-218 USB input terminal ...................................................................... 5-218Sun visors .................................................................................... 5-220 12 V power outlets ...................................................................... 5-221 USB port (for charging) (if so equipped) ..................................... 5-222 HomeLink
® Wireless Control System (if so equipped) ............... 5-223
Interior lights ............................................................................... 5-228 Storage spaces ............................................................................. 5-231Cup holders ................................................................................. 5-235 Bottle holders .............................................................................. 5-236 Cargo area cover (if so equipped) ............................................... 5-237Assist grips .................................................................................. 5-239 Coat hooks ................................................................................... 5-239 Luggage hooks ............................................................................ 5-239BK0278200US.book 2 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Keyless entry system (if so equipped) 5-10 Features and controls
5
2. Using a valid (already registered) remote control transmitter, ac
tivate the registra-
tion mode according to the following steps. Steps ii to iv should be completed within 8 seconds.
3. Within 60 seconds after step 2, complete the following ID code
registration opera-
tion using the next remote control trans- mitter you wish to register within 4 seconds. 4. To register the ID
codes of additional
remote control transmitters, repeat step 3 within 60 seconds after step 3.5. If no ID code of a remote control trans- mitter is registered within 60 seconds after step 3, the regi
stration mode is can-
celed and the normal mode returns.
i) Press and hold the
UNLOCK button (2) for 4 to 8 seconds.
ii) While holding the
UNLOCK button (2), press the LOCK but-ton (1).
iii) While holding the
UNLOCK button (2), release the LOCK but- ton (1).
iv)
Release the UNLOCK button (2).NOTE
 ID codes for all remote control transmitters except for the transmitter used in steps 2 are erased and the answerback function (door is locked and unlocked) informs you that theregistration mode ha
s been activated.
i) Press both the LOCK
and UNLOCK but- tons for 2 seconds.
ii) Release both the
LOCK and UNLOCK buttons for 1 second.
iii)
Press the UNLOCK button.NOTE
 Be sure to press the buttons correctly when performing the procedures. If you perform the procedures incorrectly, the registered ID code information could
be deleted or the set-
tings could be changed
unintentionally. If the
registered ID code in
formation is deleted,
register the remote control transmittersagain.
 For verification purposes, try to lock and unlock the doors after the registration iscompleted.  The indicator light (4) comes on each time a button is pressed.  The keyless entry system does not work if the key is in the ignition switch.  The remote control transmitter can be used from approximately 40
feet (12 m) away.
However, this distance
may change if your
vehicle is near a TV
transmitting tower, a
power station, or
a radio station.
 If the following conditi
ons are observed after
pressing the LOCK (1) or UNLOCK (2) but-ton on the remote control transmitter, the battery in the remote control transmitter may need to be replaced. • The doors and the lift
gate cannot be locked
or unlocked. • The panic alarm
cannot be operated.
• The indicator light
(4) is dim or does not
come on.
 If you lose your remote control transmitter, please contact an au
thorized Mitsubishi
Motors dealer for a replacement.  If you wish to obtain
an additional remote
control transmitter, please contact an autho-rized Mitsubishi Moto
rs dealer. A maximum
of 8 remote control tr
ansmitters can be pro-
grammed for your vehicle.NOTE
BK0278200US.book 10 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-17
5
N00503301077
The operating range is the interior of the vehicle.
N00503401472
While carrying the F.A.S.T.-key, press thedriver’s or front passenger’s door lock/unlockswitch (A), or the liftgate LOCK switch (B) within the operating range to lock all the doors and the liftgate. The turn signal lights will blink once and the buzzer will sound once. Also refer to “Doors locks”, “Power door locks”, “Liftgate” and “Power liftgate” on pages 5-36, 5-38, 5-40 and 5-42 respectively.
 Even if the F.A.S.T.-key is within about 2.3 feet (70 cm) of the handle of the driver’sdoor, front passenger’s door or liftgate, thesystem may not operate if the key is close to the ground or in a high position.  If the F.A.S.T.-key is within the operating range, even a person not carrying the F.A.S.T.-key can lock and unlock the doorsor the liftgate by pressing the driver’s or front passenger’s door lock/unlock switch, the liftgate LOCK switch or the liftgateOPEN switch.
Operating range for starting the engine and changing the opera- tion mode

NOTE
* : Front of the vehicle : Operating range
NOTE
 Even if the F.A.S.T.-key is within the operat- ing range, it may not be possible to start the engine and change the
operation mode if the
key is in a storage space such as the glovecompartment, on top of the instrument panel, or in the door pocket or luggage compart- ment.  Even if the F.A.S.T.-key is inside the vehicle, it may not be possible to
start the engine and
change the operation mode if the key is too close to a door or door window.
To operate using the F.A.S.T.- key

To l o c k

Driver’s and front passenger’s door lock/unlock switches
BK0278200US.book 17 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5-18 Features and controls
5
While carrying the F.A.S.T.-key within the operating range, you can unlock the doorsand the liftgate by using the F.A.S.T.-key operation. The dome light will turn on for 30 seconds.The turn signal lights will blink twice and the buzzer will
sound twice.
Also refer to “Door locks”, “Power door locks”, “Liftgate” and “Power liftgate” onpages 5-36, 5-38, 5-40 and 5-42 respectively. Press the driver’s door lock/unlock switch (A) to unlock only the driver’s door. Within approximately 2 seconds, press thedriver’s door lock/unlock switch one more time to unlock all the
doors and the liftgate.
Press the front passenger’s door lock/unlock switch (B) or the liftgate OPEN switch (C) to unlock all the doors and the liftgate.
NOTE
 On the vehicles equipped with the mirror retractor switch, the out
side rearview mirrors
automatically retract when all doors and lift- gate are locked using the driver’s or front passenger’s door lock/unlock switch (A) orthe liftgate LOCK switch (B).  In cases such as the following, the F.A.S.T.- key does not operate. • There is a F.A.S.T.-key in the passenger compartment • A door or the liftgate is open or ajar• The operation mode
is not in OFF.
 The liftgate OPEN switch (C) can be used to confirm that the vehicl
e is locked properly.
Press the liftgate OPEN switch withinapproximately 3 seconds of locking.  If the liftgate OPEN switch is pressed 3 sec- onds or more after the
vehicle is locked, the
doors and the liftga
te are unlocked.
Liftgate switches
The time within which locking confirmation is possible can be adjusted. See an autho-rized Mitsubishi Motors
dealer for details.
On a vehicle equipped
with the Smartphone-
link Display Audio (SDA
), the function can
be adjusted on the screen. For details, referto the separate owner’s manual.
To u n l o c k

NOTE
NOTE
 On the vehicles equipped with the mirror retractor switch, the out
side rearview mirrors
automatically extend when the driver’s door is unlocked using the
driver’s lock/unlock
switch (A), front passenger’s doorlock/unlock switch (B)
or the liftgate open
switch (C).  Settings can be change
d so that all doors and
the liftgate are unloc
ked automatically by
pressing the driver’s door lock/unlock switchonce. Refer to “Setting of door
and liftgate unlock
function” on page 5-33.Driver’s door lock/unlock switch
BK0278200US.book 18 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-19
5
N00513501216
To prevent vehicle theft, no F.A.S.T.-keys other than those regist
ered in advance can be
used to start the engi
ne. (Electronic immobi-
lizer function)While carrying the F.A.S.T.-key, the engine switch can be used
to start the engine.
NOTE
If the doors and the liftgate are unlocked using the driver’s or front passenger’s doorlock/unlock switch when all doors and the liftgate are locked and no doors or the lift- gate are opened with
in approximately 30
seconds, the doors and th
e liftgate will auto-
matically re-lock.Front passenger’s door lock/unlock switchLiftgate OPEN switch
 The amount of time af
ter unlocking until the
vehicle re-locks au
tomatically can be
adjusted. See an authorized MitsubishiMotors dealer for details. On a vehicle equipped
with the Smartphone-
link Display Audio (SDA), the functions canbe adjusted on the scre
en. For details, refer
to the separate owner’s manual.  The F.A.S.T.-key does not operate when the operation mode is not in OFF.  The doors and the liftgate cannot be unlocked by using the li
ftgate OPEN switch
for approximately 3 seconds after locking.  The time within which locking confirmation is possible can be adjusted. See an autho-rized Mitsubishi Motors
dealer for details.
On a vehicle equipped
with the Smartphone-
link Display Audio (SDA
), the function can
be adjusted on the scre
en. For details, refer
to the separate owner’s manual.  Functions settings can
be modified as stated
below. See an authorized Mitsubishi Motors dealerfor details. On a vehicle equipped
with the Smartphone-
link Display Audio (SDA), the functions canbe modified on the scre
en. For details, refer
to the separate owner’s manual. • Activating the operati
on confirmation func-
tion (blinking of the turn signal lights) only during locking, or only during unlocking.NOTE
• Deactivating the operation confirmationfunction (blinking of th
e turn signal lights)
and buzzer. • Modifying the number of blinks in the operation confirmati
on function (blinking
of the turn signal lights). • Making the buzzer sound when the F.A.S.T.-key is removed from the passenger compartment when all the doors and the liftgate are closed.
Engine switch

NOTE
BK0278200US.book 19 ページ ２０１９年４月１０日　水曜日　午前１０時５９分