▼Tires and Wheels
CAUTION
When inspecting or adjusting the tire air
pressures, do not apply excessive force to
the stem part of the wheel unit. The stem
part could be damaged.
Changing tires and wheels
The following procedure allows the TPMS
to recognize a tire pressure sensor's unique
ID signal code whenever tires or wheels
are changed, such as changing to and from
winter tires.
NOTE
Each tire pressure sensor has a unique ID
signal code. The signal code must be
registered with the
TPMS before it can
work. The easiest way to do it is to have
an Authorized Mazda Dealer, change your
tire and complete ID signal code
registration.
When having tires changed at an
Authorized Mazda Dealer
When an Authorized Mazda Dealer,
changes your vehicle's tires, they will
complete the tire pressure sensor ID signal
code registration.
When changing tires yourself
If you or someone else changes tires, you
or someone else can also undertake the
steps for the TPMS to complete the ID
signal code registration.
1. After tires have been changed, switch the ignition ON, then back to ACC or
OFF.
2. Wait for about 15 minutes.
3. After about 15 minutes, drive the vehicle at a speed of at least 25 km/h
(16 mph) for 10 mi nutes and the tire
pressure sensor ID signal code will be
registered automatically.
NOTE
If the vehicle is driven within about 15
minutes of changing tires, the tire pressure
monitoring system warning light will flash
because the sensor ID signal code would
not have been registered. If this happens,
park the vehicle for about 15 minutes,
after which the sensor ID signal code will
register upon driving the vehicle for 10
minutes.
Replacing tires and wheels
CAUTION
When replacing/repairing the tires or
wheels or both, have the work done by
an Authorized Mazda Dealer, or the tire
pressure sensors may be damaged.
The wheels equipped on your Mazda are
specially designed for installation of the
tire pressure sensors. Do not use
non-genuine wheels, otherwise it may
not be possible to install the tire pressure
sensors.
Be sure to have the tire pressure sensors
installed whenever tires or wheels are
replaced.
When having a tire or wheel or both
replaced, the following types of tire
pressure sensor installations are possible.
The tire pressure sensor is removed
from the old wheel and installed to the
new one.
When Driving
Tire Pressure Monitoring System
4-225
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07
▼Schedule 1
U.S.A. and Puerto Rico residents - En
gine oil flexible maintenance interval
Use when the maintenance monitor for “Oil Change” is set to “Flexible”. For details,
see maintenance monitor. (page 6-16)
Maintenance Interval Number of months or kilometers (miles), whichever comes first.
Months 12 24 36 48 60 72 84 96
×1000 km 12 24 36 48 60 72 84 96
×1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
SKYACTIV-G 2.0, SKYACTIV-G 2.5, AND SKYACTIV-G 2.5T
Spark plugs SKYACTIV-G
2.5T
Replace every 64,000 km (40,000 miles).
Except SKY-
ACTIV-G
2.5T Replace every 120,000 km
(75,000 miles).
Air filter RR
Drive belts II
SKYACTIV-D 2.2
Air filter CCRCCRCC
Fuel filter RR
Diesel exhaust fluid for SCR system
*1 *1 *2 *1 *1 *2 *1 *1
Glow plug*3
Drive belts II
SKYACTIV-G 2.0, SKYACTIV-G 2.5, SKYACTIV-G 2.5T, AND SKYACTIV-D 2.2
Engine oil & filter
*4Replace when wrench indicator light is ON. (Max interval: 12 months or 12,000 km (7,500 miles))
Engine coolant
*5Replace at first 192,000 km (120,0 00 miles) or 10 years; after
that, every 96,000 km (60,000 miles) or 5 years.
Fuel lines and hoses
*6IIII
Hoses and tubes for emission
*6II
Brake lines, hoses and connections I I I I
Disc brakes IIIIIIII
Tire (Rotation) Rotate every 12,000 km (7,500 miles).
Steering operation and linkages II II
Front and rear suspensi on, ball joints and wheel
bearing axial play IIII
Rear differential oil
*7
Transfer oil*7
Driveshaft dust boots II II
Maintenance and Care
Scheduled Maintenance
6-5
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07
ItemFeatureFactory Set-
ting Available
Settings Set-
tings
Chan ge
Meth od
Lane-keep Assist
System (LAS) &
Lane Departure
Warning System
(LDWS) (page
4-162) The system can be changed so that the steering
wheel assist does not operate.
On On/Off A
―
When the steer-
ing wheel opera-
tion assistance is
turned onThe system can be changed so
that the Lane Departure Warning
does not activate.
On On/Off A
―
The cancel sensitivity of the steer-
ing assistance for the Lane-keep
Assist System (LAS) & Lane De-
parture Warning System (LDWS)
can be changed. High High/Low A
―
When the steer-
ing wheel opera-
tion assistance is
turned offThe warning timin
g in which the
system determines that the vehicle
may be deviating from its lane
can be changed. At At/Before A
―
The sensitivity of the warning for
the system can be changed. Often Often/Rare A
―
Lane-keep Assist
System (LAS) &
Lane Departure
Warning System
(LDWS) (page
4-162)The type of Lane-keep Assist System (LAS) & Lane
Departure Warning System (LDWS) warning can be
changed.
Vi b r a t i o n
Vibration/
Beep/Rumbl. A
―
The warning in-
tensity/volume
of the system
can be changed. Vibration Low High/Low A
―
Rumbl.LowHigh/Mid/Lo
w A
―
Beep Low High/Low A―
Blind Spot Monitor-
ing (BSM) (page
4-128)The system can be changed
so that Blind Spot Mon-
itoring (BSM) does not operate.*1On On/Off A ―
Warning beep volume*2HighHigh/
Low/ Off A
―
Distance Recogni-
tion Support System
(DRSS) (page 4-139) The system can be changed so that Distance Recog-
nition Support System (D
RSS) does not operate.*1On On/Off A ―
The distance at which the vehicle ahead and your
vehicle indicated in the display flashes in white can
be changed. Near
Far/Med./
Near A
―
Specifications
Personalization Features
9-12
CX-5_8HX6-EA-19I_Edition2_old 2019-9-19 9:26:07
