2020 KIA CADENZA ignition

CADENZA FEATURES & FUNCTIONS GUIDE6*IF EQUIPPED
REMINDERS:
• If HDA is enabled, Lane Following Assist (LFA) automatically activates To disable LFA temporarily, press the LFA button on the Steering Wheel controls E
• Current highway speeds and controlled or limited access roads information may vary Future navigation updates may change this information See owner’s manual for more information
• If the driver changes the speed while in automatic speed setting mode, it deactivates and enters a manual mode
• When the ignition is cycled, the system returns to its previous state, on or off
B
Highway Driving Assist is not a substitute for safe driving, may not detect all objects around the vehicle, and only functions on certain federal highways. Always drive safely and use caution. See the Owner’s Manual for more detailed information, limitations and conditions.
Images are for illustrative purposes only and may not reflect actual feature or operation.
mph
60mph
Highway Driving Assist (HDA)*†6a
The Highway Driving Assist (HDA) system is designed to adjust the speed of the vehicle when driving on limited/
controlled access highways The system can adjust the vehicle’s speed based on available highway speed information
The automatic speed setting mode is designed to set the speed automatically by adjusting to the current speed limits
of the highway vehicle is travelling on
To enable the HDA system, go to Vehicle Settings* in the audio head unit Go to Drive Assistance > Driving Assist
> Highway Driving Assist
To activate the HDA, turn Smart Cruise Control (SCC) on by pressing the Cruise button A on the Steering Wheel controls
The HDA system will operate only when these conditions are met:
• When the SCC speed is set to current highway and controlled/limited access roads
•The vehicle is traveling slower than 95 mph
•
When driving on limited access highways, such as, Interstate, Federal and State freeways
•
When SCC is on and operating
When the HDA system is activated and the conditions are met, the Instrument Cluster indicator light B will
illuminate green If the conditions are not met, the HDA system will be in standby mode and the indicator light B
will illuminate white
When in operation, and if both lanes are recognized, a display C will show the lanes illuminated white and the steering
wheel indicator illuminated green
If HDA is activated, conditions are met and the SCC speed is set by the driver (at the posted highway speed limit), the
HDA system will enter the automatic speed setting mode The set speed will be displayed D in green and an audible
alert will sound
AIRBAG
CRUISEA
E
C
D
( Type B Steering Wheel controls)
INSTRUMENT CLUSTER

CADENZA FEATURES & FUNCTIONS GUIDE10*IF EQUIPPED
SMART, ECO, COMFORT and SPORT drive modes A may be changed
according the driver’s preference or road conditions To cycle through
drive modes, rotate the DRIVE MODE knob B
COMFORT Mode – The system’s default mode is COMFORT mode and may
not display on the instrument cluster nor the audio system’s screen (If set to
ECO and ignition is cycled, the system will return to ECO mode)
ECO Mode – An ECO indicator will illuminate on the instrument cluster To
deactivate, rotate the DRIVE MODE knob B again to change the selection
to another setting
SPORT Mode – A SPORT indicator will illuminate on the instrument cluster
To deactivate, rotate the DRIVE MODE knob B again to change the
selection to another setting
SMART Mode – When SMART mode is activated, the system automatically
selects the drive mode best suited to the current driving style (economic,
average, spirited) A SMART indicator will illuminate on the instrument cluster
and change colors or shades, depending on the current driving style To
deactivate, rotate the DRIVE MODE knob B again to change the selection
to another setting
3
/ %
1
"650)0-%
%3*7&.0%&
Drive Mode Integrated Control System Video
To view a video on your mobile device, snap this QR Code or visit the listed website
Refer to page 2 for more information
QR CODE
www.youtube.com/KiaFeatureVideos
For more information on ECO Mode, refer to your Owner’s Manual or contact your local dealership.
When the Engine Start/Stop button is turned off, the system will default to COMFORT mode if the vehicle was last in Sport mode
To help improve your fuel economy:
•Drive at a moderate speed, accelerating smoothly and at a moderate rate •Keep tires inflated to the recommended pressure •Be sure the wheels are properly aligned
QUICK TIPS
ECO Mode (Active ECO)
The Active ECO system is designed to
improve fuel economy by controlling several
vehicle components When activated, it
modifies drivetrain operations such as engine
power and transmission
To turn ON, rotate the DRIVE MODE knob B
and scroll through options until in the ECO
mode The ECO mode indicator light in the
LCD cluster will illuminate, indicating that
the vehicle is in ECO mode and Active ECO is
operating The Active ECO system will remain
on even when the ignition is cycled
To turn the Active ECO system OFF, rotate the
DRIVE MODE knob B again and change to
another mode
Drive Mode Integrated Control System
REMINDERS: •
When ECO mode is selected, the following may occur to help improve fuel economy: – Acceleration may be slightly reduced even when the accelerator is fully depressed – Air conditioner performance may be limited – Shift pattern of the automatic transmission may change – Engine noise may increase – System’s power will be limited when driving uphill •
Steering effort may be slightly increased in Sport mode •
When SPORT mode is selected, fuel economy may decrease
ECO
SMARTCOMFORT
SPORT
DRIVE MODE
SMART
ECO
(Knob located below Gear Shift)
B
A
VEHICLE SETTINGS

CADENZA FEATURES & FUNCTIONS GUIDE12*IF EQUIPPED
(Button panel located left of Steering Wheel)
A
Electronic Stability Control (ESC)*†8
The ESC system is designed to help stabilize the vehicle during certain
cornering maneuvers It is a good idea to keep the ESC turned on for
daily driving whenever possible
Press ESC button A to disable Traction Control in ESC (a “Traction
Control Disabled” message appears)
To turn OFF both the Traction Control and Stability Control, press and
hold for more than 3 seconds Press again to turn ON
REMINDERS:
•
ESC is active by default at vehicle start-up When ignition is cycled, ESC will turn ON again
•
The ESC Indicator Light in the instrument cluster will illuminate whenever the ESC is in operation
For more information on Electronic Stability Control (ESC) and its specific features and operations, please refer to your Owner’s Manual.
Hill-Start Assist Control (HAC)*†8
HAC is designed to prevent the vehicle from rolling backwards when
accelerating from a stop while on a steep incline The HAC automatically
activates whether the ESC is OFF or ON but does NOT activate when the
ESC has malfunctioned
REMINDER: The HAC does not operate when the gear shift is in the P (Park) or the N (Neutral) position HAC does not replace the need to apply brakes while stopped on an incline
When HAC is active (e g , during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator
QUICK TIP
DRIVER'S PANEL

13ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
B
Blind-Spot Collision-Avoidance Assist (BCA)†6a
The BCA system is designed to help alert the driver before changing lanes The BCA
system uses a camera on the front windshield and rear radar sensors in the rear
bumper to help alert the driver and temporarily apply braking in certain situations if
it detects an approaching vehicle in the driver’s blind spot area
To turn the BCA system on, go to Vehicle Settings* on the audio head unit Select Driver
Assistance > Blind Spot Safety Then select Active Assist, Warning Only or Off
Deactivate the BCA system by pressing the BCA off button A on the Driver’s Panel
Warning Only – The Warning Only setting will activate the 1st and 2nd stage alerts:
1st-stage: When another vehicle is detected within the BCA system warning
boundary B, a yellow indicator will illuminate on the outside rearview mirrors C
2nd-stage: When the 1st stage alert is on and the driver activates a turn signal, a
flashing yellow indicator will illuminate on the outside rearview mirrors and the system
will sound an alert
To set the initial warning activation time, go to the settings > Driver Assistance >
Warning Time Then select the Normal or the Late option
Active Assist – When Active Assist is selected in the settings, the BCA may activate
the Electronic Stability Control (ESC) and temporarily apply braking power when an
approaching vehicle is detected within a certain distance next to or behind the vehicle
A warning message may appear on the Instrument Cluster LCD
Conditions for the BCA system to operate:
• Warnings - When the vehicle is traveling faster than 20 mph
• Active Assist - When the vehicle is traveling at least 40 mph
• Other vehicle detected on the side of or the rear of the vehicle
The BCA system is a supplemental system. Do not solely rely on this system and always pay attention to the road and its conditions.
For more information, please refer to the Owner’s Manual.
Images are for illustrative purposes only and may not reflect actual operation.
C
REMINDERS: •
The BCA system will not issue a warning if the vehicle speed is 6 mph or more above the surrounding vehicles
•
When BCA is ON and the ignition is cycled, the BCA system returns to its previous state

The BCA Warning Volume can be adjusted in the Vehicle Settings on the audio head unit
QUICK TIP
Blind-Spot Collision- Avoidance Assist (BCA) Video
To view a video on your mobile device, snap this QR Code or visit the listed website
Refer to page 2 for more information
www.youtube.com/KiaFeatureVideos
QR CODE
A
DRIVER'S PANEL

CADENZA FEATURES & FUNCTIONS GUIDE14*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
A
Rear Cross-Traffic Collision-Avoidance Assist (RCCA)†6
If the RCCA system sensors detect approaching vehicles from the left or right side A,
the system will sound an audible alert, the warning indicators on the outside rearview
mirror will illuminate and a message will appear on the LCD screen B
RCCA is designed to operate under the following conditions::
• When the gear shift is in moved into (R) Reverse
• When the vehicle is moving less than 6 mph
REMINDERS:
•
When the BCW system is ON and the ignition is cycled to OFF then ON again, the BCW system returns to ON
•The RCCA feature can be turned OFF/ON in User Settings and will remain in OFF/ON as selected
•When vehicle power is cycled, the RCCA will remain in the previous state
•
The RCCA system will show a warning if the approaching vehicle speed is between 2 5-22 mph within sensing range See owner's manual for other conditions
The RCCA system is a supplemental system. Do not solely rely on this system and always pay attention to the road and its conditions. For more information, please refer to the Owner’s Manual.
Above images are for illustrative purposes only and may not reflect actual operation.
Watch for traffic
B
DRIVER'S PANEL

CADENZA FEATURES & FUNCTIONS GUIDE16*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
Lane Keeping Assist (LKA)†6
With the Engine Start /Stop button
in the ON position, press the LK A
button A to turn system ON The
instrument cluster indicator
will initially illuminate white It
will remain white when vehicle is
traveling less than 40 mph and the
system does not detect the lane
markers When system detects the lane markers and can assist the
steering, the LK A icon will illuminate green
If the LK A detects that you are moving outside of your lane, the system
may give an audible warning and display a Lane Departure Warning
(LDA) alert on the instrument cluster If the vehicle continues to move
outside of the lane, the LK A may apply steering inputs, trying to prevent
the vehicle from moving outside its lane
LK A is the operating mode by default when the button is depressed to
ON To switch between LK A modes, go to Vehicle Settings on the audio
head unit, select Vehicle, Driver Assistance and Lane Safety Then
select Lane Keeping Assist / Lane Departure Warning / Off
All systems will operate under the following conditions:
•The vehicle exceeds approximately 40 mph
•The LK A system recognizes both lane markers the vehicle is
traveling in
•The vehicle is between the lane markers
When the LK A sensor does not detect the lane traveling in the lanes are not illuminated
When the LK A sensor detects the vehicle moving outside of the lane traveling in, a yellow indicator will illuminate either on the left or right lane (shown in both images above)
Lane Keeping AssistLane Keeping Assist
Lane Keeping Assist
Lane Keeping Assist
Lane Keeping Assist
Lane Keeping Assist
Lane Keeping AssistLane Keeping Assist
Lane Keeping AssistLane Keeping Assist
Lane Keeping Assist
Lane Keeping Assist
Lane Keeping Assist
Lane Keeping Assist
Lane Keeping AssistLane Keeping Assist
When the LK A sensor detects the lane traveling in, both lanes are illuminated
REMINDERS:
•
LK A will not issue a warning if the turn signal or hazard signal is activated
•
If the LK A button is ON and ignition is cycled, the system will turn ON again If the LK A button is OFF, the system remains OFF
•
The LK A /LDW are not substitutes for safe and proper driving Always drive safely and use caution
•
LK A /LDW may not always alert the driver if the vehicle about to be driven outside of its lane Refer to the Owner’s Manual for more information
Lane Keeping Assist (LKA) Video
To view a video on your mobile device, snap this QR Code or visit the listed website Refer to page 2 for more information
QR CODE
www.youtube.com/KiaFeatureVideos
(Button panel located left of Steering Wheel)
A
The Lane Keeping Assist (LKA) / Lane Departure Warning are not substitutes for safe and proper driving. Always drive safely and use caution. LKA/LDW may not always alert the driver if the vehicle is about to be driven outside of its lane.
Images are for illustrative purposes only and may not reflect actual feature or operation.

The LK A Warning Volume can be adjusted in the Vehicle Settings on the audio head unit
QUICK TIP
DRIVER'S PANEL

17
(Button on right of steering wheel)
Lane Following Assist (LFA)†6
The Lane Following Assist (LFA) system monitors lane lines and adjusts
the steering to help position the vehicle in the center of the lane
To enable or disable the LFA system, go to Vehicle Settings on the audio
head unit Press Settings, Vehicle > Driver Assistance > Driving Assist
> Lane Following Assist
To activate or deactivate the LFA system press the LFA button A on the
Steering Wheel
When the LFA system is activated and detects lane markers and/or a
preceding vehicle, the LFA indicator will illuminate green if the
steering assist mode is on, or white if the steering assist mode is off
The LFA system will operate only when these conditions are met:
•When the Smart Cruise Control is on and operating
•The vehicle is traveling slower than 95 mph
A
AIRBAG
CRUISE
Images are for illustrative purposes only and may not reflect actual feature or operation.
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
REMINDERS:
•
If the ignition is cycled, the LFA returns to its previous state, on or off
•The LFA system recognizes the lane the vehicle is traveling in
•
The LFA system is not a substitute for safe and proper driving Always drive safely and use caution
See the Owner’s Manual for more detailed information, limitations and conditions.
A
DRIVER'S PANEL

23ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS *IF EQUIPPED
M I S T: Single wipe
OFF: Wiper off
AUTO: Auto Control wipe
LO: Slow wipe
HI: Fast wipe
FRONTA
B
Windshield Wipers & Washers
To o p e r a t e :
• Move lever Up/Down to change Wiper modes
• Press button A to adjust intermittent Wipe
• Pull lever to spray and wipe
Auto Control (Rain Sensing)
The rain sensor located on the upper end of the windshield
glass is designed to sense the amount of rainfall and controls
the wiping cycle for the proper interval The more it rains, the
faster the wiper operates When the rain stops, the wiper stops
To adjust the Auto Rain Sensing speed setting, move the speed
control switch A up/down
Lifting Wipers / Wiper Service Mode
To inspect or replace the windshield wiper blades to prevent damaging the hood, the
blades need to be moved to the service position A
With the ignition ON, then turning the ignition OFF, within 20 seconds move the wiper
switch to the MIST position B and hold the switch for more than two seconds until the
wiper blade is in the fully up position
To return wipers to normal position, turn the ignition ON, then activate MIST

•With the ENGINE START/STOP button in the ON position and the wiper switch is in AUTO mode, the wiper will operate once to perform a self-check of the system
•Moving lever to HI increases Intermittent wipe frequency and wipe speed Moving lever to LO decreases frequency of wipes
•When in AUTO mode, pressing button A up increases Intermittent wipe frequency and wipe speed Pressing button down decreases frequency of wipes
•Set the wiper to OFF position when the wiper is not in use
QUICK TIPS
STEERING WHEEL CONTROLS