43ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
How to Sync Transmitter with HomeLink®
If programming for the first time, begin with Step 1 (repeating
this step will delete all information)
To program non-rolling and rolling code garage door openers
and other devices:
1 Press and release one of the Homelink® buttons The
indicator light will turn orange
2 Press and hold the desired Homelink® button you’re
programming for 15-25 seconds until the orange indicator
flashes several times Hold the original garage door opener
transmitter approximately 1 to 3 inches away from the
mirror and press and hold the transmitter button The
HomeLink® Indicator light 8 will turn green and flash
rapidly once the frequency signal has been successfully
programmed
To finish programming rolling code garage door openers,
complete these steps:
3 Locate the “learn” or “smart” button on the garage door’s motor head unit Press and
release the button and complete Step 4 within 30 seconds
4 Firmly press and release the programmed HomeLink® button up to three times
Operating HomeLink®: Press one of the programmed HomeLink® buttons
Erasing programmed buttons: Press and hold Homelink® buttons 1 and 3 simultaneously
for approximately 20 seconds, and then release both buttons within 30 seconds The indicator
above the Homelink® buttons will turn orange for about 10 seconds, then turn green and flash
rapidly
HomeLink®†13 with Auto-Dimming
Rearview Mirror
1 Virtual Assist button
2 UVO button
3 Roadside Assist button
4 Homelink® Channel 1 button
5 Homelink® Channel 2 button
6 Homelink® Channel 3 button
7 Garage Door Closing/Closed Status Light
8 Homelink® Operation Light
9 Garage Door Opening/Open Status Light
10 Homelink® User Interface Light
11 Compass Display
The HomeLink® / Auto-Dimming Rearview Mirror is
designed to reduce glare from a vehicle’s headlights
located in the rear and also connect up to three
electronic transmitters into one location
REMINDER: Mirror indicator light 8 will illuminate when automatic dimming is ON
•You can reprogram a single HomeLink® button by repeating Step 2 •Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
HomeLink® Setup Video
To view a video on your mobile device, snap this QR Code or visit the listed website Refer to page 2 for more information
QR CODE
www.youtube.com/KiaFeatureVideos
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.
SE11
123456
79
810
OTHER KEY FEATURES
51ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
Driver Attention Warning (DAW)*†7
The DAW system is designed to detect inattentive driving practices, in
certain situations, can give a warning signal to take a break from driving
The DAW system is set to ON by default To turn the DAW system OFF, turn
the ignition on and go to Vehicle Settings in the audio head unit Select
Vehicle > Driver Assistance > Driver Attention Warning > Inattentive Driving
Warning The Warning Time* can be set
Normal (Default): The Driver Attention Warning system alerts the driver of
his/her inattentive driving practices
Late: The Driver Attention Warning system alerts the driver of his/her
inattentive driving practices later than Normal mode
If the DAW System is activated, the DAW information will appear on the LCD
Display A when you select the ASSIST mode
A message, “Consider taking a break,” appears on the LCD display and
a warning sounds to suggest the driver to take a break when the driver’s
attention level is below one bar B
REMINDERS:
•The set-up of the DAW System will be maintained, as selected, when the ignition is cycled
•
When activated, the DAW System does not display “Consider taking a break” message when the total trip driving time is less than 10 minutes
•
The DAW System will enter a standby mode if the camera does not detect the lanes and/or the driving speed remains under 40 mph
Driver Attention Warn.
System Off
Last Break ——:——Attention Level
LOW HIGH
Last Break 05:27
Attention Level
LOWHIGH
Level Time 05:27
Consider taking a break
22.4
