Page 314 of 412
W $ 5N ,N *
Do not attempt to change a tire on the side
of the vehicle close to moving traffic. Pull
far enough off the road to avoid the danger
of being hit when operating the jack or
changing the wheel.
Being under a jacked-up vehicle is
dangerous. The vehicle could slip off the
jack and fall on you. You could be crushed.
Never put any part of your body under a
vehicle that is on a jack. If you need to get
under a raised vehicle, take it to a service
center where it can be raised on a lift.
Never start or run the engine while the
vehicle is on a jack.
The jack is designed to be used as a tool for
changing tires only. The jack should not be
used to lift the vehicle for service purposes.
The vehicle should be jacked on a firm level
surface only. Avoid ice or slippery areas.
CAUTION!
Always lift or jack the vehicle from the correct
jacking points. Failure to follow this informa-
tion could cause damage to the vehicle or
underbody components.
WARNING!
Do not attempt to change a tire on the side of
the vehicle close to moving traffic. Pull far
enough off the road to avoid being hit when
operating the jack or changing the wheel.
Page 316 of 412
WARNING!
Carefully follow these tire changing warnings
to help prevent personal injury or damage to
your vehicle:
Always park on a firm, level surface as far
from the edge of the roadway as possible
before raising the vehicle.
Turn on the Hazard Warning Flashers.
Apply the parking brake firmly and set the
transmission in PARK.
Block the wheel diagonally opposite the
wheel to be raised.
Never start or run the engine with the
vehicle on a jack.
Do not let anyone sit in the vehicle when it
is on a jack.
Do not get under the vehicle when it is on a
jack. If you need to get under a raised
vehicle, take it to a service center where it
can be raised on a lift.
WARNING! (Continuedyf
Page 326 of 412
W $ 5N ,N *
)a Vt V S L Q Q L Qg t L Ue V Fa Q be Ga Qge Uo X V. )o U Fe V
ge Qe Uate G b \ e [ Fe V V L Ye Z Kee O V See G V Pa \
Fa X Ve Ga Page o U e Ye Q Ia L O X Ue o I t Ke a [ Oe
a Q G t L Ue V. $ t L Ue Fo X O G e [ S Oo Ge a Q G L Q M X Ue
Vo Peo Qe. 'o Qot V S L Q \o X U Ye K L F Oe
V Z Kee O V
Ia Vte U t Ka Q 30 P S K 48 k P K \f R U I R U O R Q J H U t Ka Q 30 Ve Fo Q G V Fo Qt L Q Xo X V O \ Z Lt Ko Xt
Vto S S L Qg Z Ke Q \o X a Ue Vt X Fk a Q G Go Qot Oet
a Q \o Qe Qea U a V S L Q Q L Qg Z Kee O Qo Patte U
Z Kat t Ke V See G.
C $U 7 ,ON
Racing the engine or spinning the wheels
may lead to transmission overheating and
failure. Allow the engine to idle with the
transmission in NEUTRAL for at least one
minute after every five rocking-motion
cycles. This will minimize overheating and
reduce the risk of transmission failure
during prolonged efforts to free a stuck
vehicle.
Page 331 of 412
SERVICING AND MAINTENANCE
SC \b \fED SERVICING
Your vehicle is equipped with an automatic oil
change indicator system. The oil change
indicator system will remind you that it is time to
take your vehicle in for scheduled maintenance.
Based on engine operation conditions, the oil
change indicator message will illuminate. This
means that service is required for your vehicle.
Operating conditions such as frequent
short-trips, trailer tow, extremely hot or cold
ambient temperatures, and E85 fuel usage will
influence when the “Oil Change Required”
message is displayed. Severe operating
conditions can cause the change oil message to
illuminate as early as 3,500 miles (5,600 kmyf since last reset. Have your vehicle serviced as
soon as possible, within the next 500 miles
(805 kmyf . An authorized dealer will reset the oil change
indicator message after completing the
scheduled oil change.
NOTE:
Under no circumstances should oil change
intervals exceed 10,000 miles (16,000 kmyf
12 months or 350 hours of engine run time,
whichever comes first. The 350 hours of engine
run or idle time is generally only a concern for
fleet customers.
Severe Duty All Models
Vehicles that are operated in a dusty and
off-road environment, or predominately at idle
or very low engine RPM are known as Severe
Duty vehicles. It is recommended that you
change engine oil at 4,000 miles (6,500 kmyf R U
350 hours of engine run time.
Once A Month Or Before A Long Trip:Check engine oil level
Check windshield washer fluid level
Check the tire pressures and look for unusual
wear or damage
Check the fluid levels of the coolant reservoir,
brake master cylinder and fill as needed
Check function of all interior and exterior
lights
8
21_WK_OM_EN_USC_t.book Page 329
Page 340 of 412
WARNING!
The air induction system (air cleaner, hoses,
etc.yf F D Q S U R Y L G H D P H D V X U H R I S U R W H F W L R Q L Q
the case of engine backfire. Do not remove
the air induction system (air cleaner, hoses,
etc.yf X Q O H V V V X F K U H P R Y D O L V Q H F H V V D U \ I R U
repair or maintenance. Make sure that no
one is near the engine compartment before
starting the vehicle with the air induction
system (air cleaner, hoses, etc.yf U H P R Y H G
Failure to do so can result in serious personal
injury.
1 — Engine Air Cleaner Filter Cover
2 — Spring Clips
1 — Engine Air Cleaner Filter Cover
2 — Engine Air Cleaner Filter
Page 348 of 412
W $ 5N ,N *
You or others can be badly burned by hot
engine coolant (antifreezeyf R U V W H D P I U R P
your radiator. If you see or hear steam
coming from under the hood, do not open
the hood until the radiator has had time to
cool. Never open a cooling system pressure
cap when the radiator or coolant bottle is
hot.
Keep hands, tools, clothing, and jewelry
away from the radiator cooling fan when
the hood is raised. The fan starts automati-
cally and may start at any time, whether the
engine is running or not.
When working near the radiator cooling fan,
disconnect the fan motor lead or turn the
ignition to the OFF mode. The fan is
temperature controlled and can start at any
time the ignition is in the ON mode.
Page 350 of 412
W $ 5N ,N *
Do not open hot engine cooling system.
Never add engine coolant (antifreezeyf Z K H Q
the engine is overheated. Do not loosen or
remove the cap to cool an overheated
engine. Heat causes pressure to build up in
the cooling system. To prevent scalding or
injury, do not remove the pressure cap
while the system is hot or under pressure.
Do not use a pressure cap other than the
one specified for your vehicle. Personal
injury or engine damage may result.
Page 387 of 412
TEC \b \f SPECIFICATIONS
VE \b \fE IDENTIFICATION NUMBER
The Vehicle Identification Number (VINyf L V I R X Q G
on a label located on the left front corner of the
instrument panel pad, visible from outside of
the vehicle through the windshield.
Windshield VIN Label Location
NOTE:
It is illegal to remove or alter the VIN.
BRAKE SYSTEM
Your vehicle is equipped with dual hydraulic
brake systems. If either of the two hydraulic
systems loses normal capability, the remaining
system will still function. However, there will be some loss of overall braking effectiveness. You
may notice increased pedal travel during
application, greater pedal force required to slow
or stop, and potential activation of the Brake
Warning Light.
In the event power assist is lost for any reason
(i.e., repeated brake applications with the
engine offyf W K H E U D N H V Z L O O V W L O O I X Q F W L R Q
However, the effort required to brake the
vehicle will be much greater than that required
with the power system operating.
W \b \f AND TIRE TORQUE SPECIFICATIONS
Proper lug nut/bolt torque is very important to
ensure that the wheel is properly mounted to
the vehicle. Any time a wheel has been removed
and reinstalled on the vehicle, the lug nuts/
bolts should be torqued using a properly
calibrated torque wrench using a six sided (hexyf
deep wall socket.
TORQUE SPECIFICATIONS
**Use only authorized dealer recommended lug nuts/
bolts and clean or remove any dirt or oil before tightening.
Inspect the wheel mounting surface prior to
mounting the tire and remove any corrosion or
loose particles.
Wheel Mounting Surface
Tighten the lug nuts/bolts in a star pattern until
each nut/bolt has been tightened twice. Ensure
that the socket is fully engaged on the lug nut/
bolt (do not insert it half wayyf .
Lug Nut/Bolt Torque **Lug Nut/
Bolt Size Lug Nut/Bolt
Socket Size
130 Ft-Lbs (176 N·myf M14 x 1.50 22 mm
9
21_WK_OM_EN_USC_t.book Page 385
![JEEP GRAND CHEROKEE TRAILHAWK 2020 Owners Manual W $ 5N ,N *
)a Vt V S L Q Q L Qg t L Ue V Fa Q be Ga Qge Uo X V. )o U Fe V
ge Qe Uate G b \ e [ Fe V V L Ye Z Kee O V See G V Pa \
Fa X Ve Ga Page o U e Ye Q Ia L O X Ue o I t Ke a](/manual-img/16/56018/w960_56018-325.png "JEEP GRAND CHEROKEE TRAILHAWK 2020 Owners Manual W $ 5N ,N *
)a Vt V S L Q Q L Qg t L Ue V Fa Q be Ga Qge Uo X V. )o U Fe V
ge Qe Uate G b \ e [ Fe V V L Ye Z Kee O V See G V Pa \
Fa X Ve Ga Page o U e Ye Q Ia L O X Ue o I t Ke a")
