171
(Continued)
For example: If approaching the left side
of the lane the steering wheel will turn to
the right.
When the LaneSense system senses the
lane has been approached and is in a lane
departure situation, the left thick lane line
flashes yellow (on/off) and the left thin
line remains solid yellow. The LaneSense
telltale changes from solid yellow to
flashing yellow. At this time torque is
applied to the steering wheel in the oppo-
site direction of the lane boundary.For example: If approaching the left side
of the lane the steering wheel will turn to
the right.
NOTE:
The LaneSense system operates with the
similar behavior for a right lane departure.
Changing LaneSense Status
The LaneSense system has settings to adjust
the intensity of the torque warning and the
warning zone sensitivity (early/late) that you
can configure through the Uconnect system
screen.
Refer to “Uconnect Settings” in “Multi -
media” in the Owner’s Manual for further
information. NOTE:
When enabled, the system operates above
37 mph (60 km/h) and below 112 mph
(180 km/h).
Use of the turn signal suppresses the
warnings.
The system will not apply torque to the
steering wheel whenever a safety system
engages (Anti-Lock Brakes, Traction
Control System, Electronic Stability
Control, Forward Collision Warning, etc.).
PARKVIEW REAR BACK UP
CAMERA — IF EQUIPPED
Your vehicle may be equipped with the
ParkView Rear Back Up Camera that allows
you to see an on-screen image of the rear
surroundings of your vehicle whenever the
gear selector is put into REVERSE. The
image will be displayed in the touchscreen
display along with a caution note to “check
entire surroundings” across the top of the
screen. After five seconds this note will
disappear. The ParkView camera is located
on the rear of the vehicle above the rear
license plate. NOTE:
The ParkView Rear Back Up Camera has
programmable modes of operation that may
be selected through the Uconnect System.
Refer to “Uconnect Settings” in “Multi
-
media” in the Owner’s Manual for further
information.
WARNING!
Drivers must be careful when backing up
even when using the ParkView Rear Back
Up Camera. Always check carefully behind
your vehicle, and be sure to check for
pedestrians, animals, other vehicles,
obstructions, or blind spots before backing
up. You are responsible for the safety of
your surroundings and must continue to
pay attention while backing up. Failure to
do so can result in serious injury or death.
CAUTION!
To avoid vehicle damage, ParkView
should only be used as a parking aid. The
ParkView camera is unable to view every
obstacle or object in your drive path.
2020_JEEP_CHEROKEE_UG_RHD_UK.book Page 171
195(Continued)
NOTE:
The jack handle attaches to the side of the
jack with two attachment points. When the
jack is partially expanded, the tension
between the two attachment points holds the
jack handle in place.
7. Remove the spare tire.
Preparations For Jacking
1. Park the vehicle on a firm level surface asfar from the edge of the roadway as
possible. Avoid icy or slippery areas. 2. Turn on the Hazard Warning flasher.
3. Apply the parking brake.
4. Place the gear selector into PARK (P)
(automatic transmission) or REVERSE
(R) (manual transmission).
5. Turn the ignition OFF.
6. Chock both the front and rear of the wheel diagonally opposite of the jacking
position. For example, if changing the
right front tire, chock the left rear wheel.
Wheel Chocks NOTE:
Passengers should not remain in the vehicle
when the vehicle is being raised or lifted.
Jacking Instructions
WARNING!
A loose tire or jack thrown forward in a
collision or hard stop could endanger the
occupants of the vehicle. Always stow the
jack parts and the spare tire in the places
provided. Have the deflated (flat) tire
repaired or replaced immediately.
WARNING!
Do not attempt to change a tire on the side
of the vehicle close to moving traffic. Pull
far enough off the road to avoid being hit
when operating the jack or changing the
wheel.
WARNING!
Carefully follow these tire changing
warnings to help prevent personal injury or
damage to your vehicle:
Always park on a firm, level surface as
far from the edge of the roadway as
possible before raising the vehicle.
Turn on the Hazard Warning flasher.
Chock the wheel diagonally opposite the
wheel to be raised.
Apply the parking brake firmly and set an
automatic transmission in PARK; a
manual transmission in REVERSE.
Never start or run the engine with the
vehicle on a jack.
Do not let anyone sit in the vehicle when
it is on a jack.
Do not get under the vehicle when it is
on a jack. If you need to get under a
raised vehicle, take it to a service center
where it can be raised on a lift.
2020_JEEP_CHEROKEE_UG_RHD_UK.book Page 195
IN CASE OF EMERGENCY
206
3. Place the transmission in PARK (P) (autotransmission) or in Gear (manual trans -
mission) and place the ignition in the
OFF position.
4. Apply the parking brake.
(B) Setting Up To Use Tire Service Kit:
1. Push in the Mode Select Knob and turn to the Sealant Mode position.
2. Uncoil the Sealant Hose and then remove the cap from the fitting at the end of the
hose.
3. Place the Tire Service Kit flat on the ground next to the deflated tire.
4. Remove the cap from the valve stem and then screw the fitting at the end of the
Sealant Hose onto the valve stem.
5. Uncoil the Power Plug and insert the plug into the vehicle’s 12 Volt power outlet.
NOTE:
Do not remove foreign objects (e.g., screws
or nails) from the tire.
(C) Injecting Tire Service Kit Sealant Into
The Deflated Tire:
Always start the engine before turning ON
the Tire Service Kit.
NOTE:
Manual transmission vehicles must have the
parking brake engaged and the gear selector
in NEUTRAL.
After pushing the Power Button, the
sealant (white fluid) will flow from the
Sealant Bottle through the Sealant Hose
and into the tire.
NOTE:
Sealant may leak out through the puncture in
the tire. If the sealant (white fluid) does not flow within
0 – 10 seconds through the Sealant Hose:
1. Push the Power Button to turn Off the
Tire Service Kit. Disconnect the Sealant
Hose from the valve stem. Make sure the
valve stem is free of debris. Reconnect
the Sealant Hose to the valve stem.
Check that the Mode Select Knob is in
the Sealant Mode position and not Air
Mode. Push the Power Button to turn On
the Tire Service Kit.
2. Connect the Power Plug to a different 12 Volt power outlet in your vehicle or another
vehicle, if available. Make sure the engine is
running before turning ON the Tire Service
Kit.
3. The Sealant Bottle may be empty due to previous use. Call for assistance.
NOTE:
If the Mode Select Knob is on Air Mode and
the pump is operating, air will dispense from
the Air Pump Hose only, not the Sealant
Hose.
If the sealant (white fluid) does flow through the
Sealant Hose: 1. Continue to operate the pump until
sealant is no longer flowing through the
hose (typically takes 30 - 70 seconds). As the sealant flows through the Sealant
Hose, the Pressure Gauge can read as
high as 70 psi (4.8 Bar). The Pressure
2020_JEEP_CHEROKEE_UG_RHD_UK.book Page 206
213
You can also turn the temperature control
to maximum heat, the mode control to
floor and the blower control to high. This
allows the heater core to act as a supple-
ment to the radiator and aids in removing
heat from the engine cooling system.GEAR SELECTOR OVERRIDE
If a malfunction occurs and the gear selector
cannot be moved out of the PARK position,
you can use the following procedure to
temporarily move the gear selector:
1. Turn the engine OFF.
2. Apply the parking brake.
3. Using a screwdriver or similar tool, care-
fully separate the shifter bezel and boot
assembly from the center console, and
raise it up to access the gear selector
mechanism.
4. Press and maintain firm pressure on the brake pedal. 5. Insert a small screwdriver or similar tool
down into the gear selector override
access hole (at the left front corner of the
gear selector assembly), and push and
hold the override release lever down.
Override Access Hole
6. Move the gear selector to the NEUTRAL position.
7. The vehicle may then be started in NEUTRAL.
8. Reinstall the gear selector boot.
WARNING!
You or others can be badly burned by hot
engine coolant (antifreeze) or steam from
your radiator. If you see or hear steam
coming from under the hood, do not open
the hood until the radiator has had time to
cool. Never try to open a cooling system
pressure cap when the radiator or coolant
bottle is hot.
2020_JEEP_CHEROKEE_UG_RHD_UK.book Page 213
IN CASE OF EMERGENCY
214
FREEING A STUCK VEHICLE
If your vehicle becomes stuck in mud, sand
or snow, it can often be moved using a
rocking motion. Turn the steering wheel right
and left to clear the area around the front
wheels. For vehicles with automatic trans-
mission, push and hold the lock button on
the gear selector. Then shift back and forth
between DRIVE and REVERSE (with auto -
matic transmission) or SECOND GEAR and
REVERSE (with manual transmission), while
gently pressing the accelerator.
NOTE:
For vehicles with automatic transmission:
Shifts between DRIVE and REVERSE can
only be achieved at wheel speeds of 5 mph
(8 km/h) or less. Whenever the transmission
remains in NEUTRAL for more than two
seconds, you must press the brake pedal to
engage DRIVE or REVERSE.
Use the least amount of accelerator pedal
pressure that will maintain the rocking
motion without spinning the wheels or racing
the engine. NOTE:
Push the “ESC OFF” switch (if necessary), to
place the Electronic Stability Control (ESC)
system in “Partial Off” mode, before rocking
the vehicle. Refer to “Electronic Brake
Control System” in “Safety” for further infor
-
mation. Once the vehicle has been freed,
push the "ESC OFF" switch again to restore
“ESC On” mode.
CAUTION!
Racing the engine or spinning the wheels
may lead to transmission overheating
and failure. Allow the engine to idle with
the transmission in NEUTRAL for at
least one minute after every five
rocking-motion cycles. This will mini -
mize overheating and reduce the risk of
clutch or transmission failure during
prolonged efforts to free a stuck vehicle.
When “rocking” a stuck vehicle by
shifting between DRIVE/SECOND GEAR
and REVERSE, do not spin the wheels
faster than 15 mph (24 km/h), or drive -
train damage may result.
Revving the engine or spinning the
wheels too fast may lead to transmission
overheating and failure. It can also
damage the tires. Do not spin the wheels
above 30 mph (48 km/h) while in gear
(no transmission shifting occurring).
WARNING!
Fast spinning tires can be dangerous.
Forces generated by excessive wheel
speeds may cause damage, or even failure,
of the axle and tires. A tire could explode
and injure someone. Do not spin your
vehicle's wheels faster than 30 mph
(48 km/h) or for longer than 30 seconds
continuously without stopping when you
are stuck and do not let anyone near a
spinning wheel, no matter what the speed.
2020_JEEP_CHEROKEE_UG_RHD_UK.book Page 214
215
TOWING A DISABLED VEHICLE
This section describes procedures for towing a disabled vehicle using a commercial towing service.
Proper towing or lifting equipment is
required to prevent damage to your vehicle.
Use only tow bars and other equipment
designed for this purpose, following equip-
ment manufacturer’s instructions. Use of
safety chains is mandatory. Attach a tow bar
or other towing devices to main structural
members of the vehicle, not to bumpers or
associated brackets. State and local laws
regarding vehicles under tow must be
observed.
NOTE:
You must ensure that the Auto Park Brake
feature is disabled before towing this
vehicle, to avoid inadvertent Electric Park
Brake engagement. The Auto Park Brake feature is enabled or disabled via the
customer programmable features in the
Uconnect Settings.
Vehicles with a discharged battery or total
electrical failure when the electric park
brake (EPB) is engaged, will need a wheel
dolly or jack to raise the rear wheels off the
ground when moving the vehicle onto a
flatbed.
If you must use the accessories (wipers,
defrosters, etc.) while being towed, the igni -
tion must be in the ON/RUN mode, not the
ACC mode. NOTE:
The Safehold feature will engage the Electric
Park Brake whenever the driver's door is
opened (if the battery is connected, ignition
is ON, transmission is not in PARK, and
brake pedal is released). If you are towing
this vehicle with the ignition in the ON/RUN
mode, you must manually disable the Elec
-
tric Park Brake each time the driver's door is
opened, by pressing the brake pedal and
then releasing the EPB.
If the vehicle’s battery is discharged, refer to
“Gear Selector Override” in this section for
instructions on shifting the automatic trans -
mission out of PARK so that the vehicle can
be moved.
Towing Condition Wheels OFF The
GroundFWD MODELS
4X4 MODELS
Flat Tow NONENOT ALLOWED NOT ALLOWED
Wheel Lift Or Dolly Tow Rear NOT ALLOWED NOT ALLOWED
Front OK NOT ALLOWED
Flatbed ALLBEST METHOD ONLY METHOD
2020_JEEP_CHEROKEE_UG_RHD_UK.book Page 215
323
Brake System ............................ 234, 255
Anti-Lock (ABS) ............................. 255 Fluid Check ........................... 235 , 265
Master Cylinder .............................. 235
Parking ......................................... 141
Warning Light .................................. 64
Brake/Transmission Interlock .............. 147
Bulb Replacement ............................. 183
Bulbs, Light ...................................... 137
C
Camera, Rear .................................... 171
Capacities, Fluid................................ 261
Caps, Filler Oil (Engine) ............ 229 , 230 , 231 , 232
Car Washes ....................................... 252
Certification Label ............................. 177
Change Oil Indicator ............................ 60
Changing A Flat Tire .................. 194 , 241
Checking Your Vehicle For Safety ........ 134
Checks, Safety .................................. 134
Child Restraint .................................. 118
Child Restraints Child Seat Installation .................... 129
How To Stow An unused ALR Seat Belt ............................ 129
Cleaning Wheels .......................................... 248
Climate Control ................................... 36 Clock Settings ................................... 269
Compact Spare Tire ........................... 247
Cooling System ................................. 234
Cooling Capacity ............................ 261
Inspection ..................................... 234
Selection Of Coolant (Antifreeze) .........................261 , 262
Cruise Control (Speed Control) .....160 , 161
Cruise Light ............................. 72 , 73 , 74
Customer Assistance .......................... 308
Cybersecurity .................................... 268
D
Daytime Running Lights ....................... 30
Dealer Service ................................... 237
Defroster, Windshield......................... 136
Diagnostic System, Onboard ................. 74
Diesel Display Messages ............................. 61
Dipsticks Oil (Engine) ................................... 233
Disabled Vehicle Towing .................... 215
Do Not Disturb ...........................297 , 305
Door Ajar .......................................65 , 66
Door Ajar Light ...............................65 , 66
Doors ................................................. 19
Drag And Drop Menu ..................273 , 278
Driver’s Seat Back Tilt ......................... 22 E
Easy Entry Seats ..................................24
Electric Brake Control System ...............77
Anti-Lock Brake System ....................76
Electronic Roll Mitigation ............ 78 , 87
Electric Parking Brake ........................141
Electrical Power Outlets ........................55
Electronic Speed Control
(Cruise Control) .......................... 160 , 161
Electronic Stability Control (ESC) ..........79
Electronic Throttle Control Warning
Light ...................................................65
Emergency Braking ..............................93
Emergency Gas Can Refueling .............212
Emergency, In Case Of Gear Selector Override ....................213
Hazard Warning Flasher ..................182
Jacking .................................. 194 , 241
Jump Starting ................................209
Emissions..........................................266
Engine .......................229 , 230 , 231 , 232
Break-In Recommendations .............140 Checking Oil Level ..........................233
Coolant (Antifreeze) ........................262
Cooling ..........................................234Fuel Requirements ................. 257 , 261
Jump Starting ................................209
2020_JEEP_CHEROKEE_UG_RHD_UK.book Page 323
324
INDEX
Oil ........................................ 261, 262
Oil Filler Cap .......... 229 , 230 , 231 , 232
Oil Selection .................................. 261
Overheating ................................... 212
Enhanced Accident Response
Feature ..................................... 115 , 217
Exterior Lights ............................. 30 , 137
F
Filters Air Conditioning ............................... 47
Engine Oil ..................................... 262
Flashers Hazard Warning ............................. 182Turn Signals ............................ 73 , 137
Flash-To-Pass ...................................... 31
Flat Tire Changing ..................... 241 , 246
Flat Tire Stowage ....................... 241 , 246
Fluid Capacities................................. 261
Fluid Leaks ....................................... 137
Fluid Level Checks Brake ............................................ 235
Engine Oil ..................................... 233
Fluid, Brake ...................................... 265
Fluids And Lubricants ........................ 262
Fob, Key ............................................. 13
Fog Lights ..................................... 32 , 71
Fog Lights, Rear .................................. 32 Fold-Flat Seats .................................... 22
Forward Collision Warning .................... 90
Four Wheel Drive ............................... 150
Freeing A Stuck Vehicle ..................... 214
Fuel
Additives ....................................... 257
Consumption ................................. 266
Light............................................... 68
Materials Added............................. 257
Octane Rating................................ 262
Requirements ................................ 261
Specifications................................ 262
Tank Capacity................................ 261
Fueling ......................................172 , 173
Fuses ............................................... 184
G
Gasoline Particulate Filter (GPF) ........... 58
Gear Ranges ..............................144 , 148
Gear Selector Override ....................... 213
Glass Cleaning .................................. 254
GVWR .............................................. 178
H
Hazard Warning Flashers .................... 182
Head Restraint Removal ....................... 26
Head Restraints .................................. 26
Head Rests ......................................... 26 Headlights ...........................................30
Automatic ........................................31
Automatic High Beam .......................31
High Beam................................. 30 , 31
High Beam/Low Beam Select Switch ..... 31
On With Wipers ................................31
Passing...................................... 30 , 31
Switch .............................................30 Time Delay.......................................32
Heated Seats ................................. 24 , 25
Heated Steering Wheel .........................28
Hill Descent Control .............................83
Hill Descent Control Indicator ...............83
Hill Start Assist....................................81
Hood Prop ...........................................52
Hood Release ......................................52
I
Ignition ...............................................15 Switch .............................................15
Instrument Cluster ...............................60 Descriptions .....................................73
Display ............................................59Menu Items .....................................61
Instrument Panel Lens Cleaning ..........254
Interior Appearance Care ....................253
Introduction ..........................................1
Inverter Power ..............................................56
2020_JEEP_CHEROKEE_UG_RHD_UK.book Page 324